Mode d’emploi Adler AD 4123 Presse-fruits

Mode d’emploi

5

DESCRIPTION OF DEVICE

1. Pusher 2. Filling hole

3. Pulp container 4. Power cord

5.3-position switch 6. Base with motor

7. Spout 8. Cover

9. Grater and filter basket 10. Juice and pulp separating bowl

11. Safety locking handle

BEFORE FIRST USE

1. Wash the parts of the unit, which will be in contact with food .

2. Try to assemble and disassemble the unit for a few times before start working with the units.

DISMANTLING AND ASSEMBLE

1. Turn the 3 position switch (5) to off, release the safety locking handle (11).

2. Remove the cover (8).

3. Remove the juice and pulp separating bowl (10), then pull the stainless steel grater and filter basket (9) upwards.to assemble device:

4. Place the juice and pulp separating bowl (10) on base with heavy duty 1000 W motor (6), push with both hands on the juice and pulp

separating bowl (10).

5. Insert the cover (8) and stainless steel grater and filter basket (9).

6. Disclose the cover (8) and fasten safety locking handle (11). lain

7. Put on the large pulp container (3) properly, then fix up the set the juice jar.

OPERATING

1. Wash your selection of fruit and vegetables ready for juicing. Most fruit and vegetables such as apples, carrots and cucumbers will not

need to be cut to size as these will fit into the feed chute whole.

2. Ensure the power juicer is correctly assembled. Ensure the stainless steel filter is thoroughly cleaned before each use.

3. Plug the power cord into a properly power outlet and turn the power '1'. Push the two speed switch either in ‘1’ position - for low speed or

‘2’position - for high speed, depending on the type of fruit or vegetable being juiced. Use the speed selector table as a guide for juicing

different fruits and vegetable.

4. With the motor running, place food into the feed chute. Using the food pusher, gently guide food down the feed chute. To extract the

maximum amount of juice, always push the food pusher down slowly.

5. Juice will flow into the juice jug and the separated pulp will accumulate in the pulp container. The pulp container can be emptied during

juicing by turning off the Juicer and then carefully removing the pulp container. (Replace empty pulp container before continuing to juice).

Do not allow the pulp container to overfill - that may damage the unit.

CLEANING AND MAINTENANCE

1. For easy cleaning - immediately after each use rinse removable parts under running water (to remove wet pulp). Allow parts to dry.

2. After disassembling the unit all removable parts may be washed in hot soapy water.

3. The juicer cover , filter bowl surround, pulp container, stainless steel filter basket and juice jar are dishwasher safe (top shelf only).

4. Wipe the motor base with a damp cloth.

5. Do not soak the stainless steel filter basket (9) in bleach.

6. Always treat the filter basket (9) with care as it can be easily damaged.

7. Discoloration of the plastic may occur with strongly colored fruit and vegetables. To help prevent this, wash parts immediately after use.

8. If discoloration does occur, the plastic parts can be soaked in 10% lemon juice and water or they can be cleaned with a non abrasive

cleaner. To assist with cleaning soak the stainless steel filter basket (9) in hot soapy water for approximately 10 minutes immediately after

juicing is completed. If pulp is left to dry on the filter it may clog the fine pores of the filter mesh thereby lessening the effectiveness of the

juicer. For your convenience a nylon cleaning brush has been included with your juicer.

TECHNICAL DATA

Voltage: 220-240 V ~ 50 Hz

Power: 1000 W/150W

Two speeds mode:

Hi - switch in position ‘2’,

Low - switch in position ‘1’.

Safety switch

Short term operation: 3min - 30 minut stop

DEUTSCH

To protect your environment: please separate carton boxes and plastic bags and dispose them in corresponding

waste bins. Used appliance should be delivered to the dedicated collecting points due to hazarsous

components, which may effect the environment. Do not dispose this appliance in the common waste bin.

Évaluation

En savoir plus sur ce mode d’emploi

Nous comprenons qu’il est agréable d’avoir un mode d’emploi papier pour vos Adler AD 4123 Presse-fruits. Vous pouvez toujours télécharger le mode d’emploi depuis notre site Web et l’imprimer vous-même. Si vous souhaitez disposer d’un mode d’emploi original, nous vous recommandons de contacter Adler. Ils pourront peut-être fournir un mode d’emploi original. Recherchez-vous le mode d’emploi de votre Adler AD 4123 Presse-fruits dans une autre langue ? Choisissez votre langue préférée sur notre page d’accueil et recherchez le numéro de modèle pour voir si nous l’avons disponible.

Caractéristiques

Tous les modes d’emploi pour Adler Presse-fruits
Plus de modes d’emploi de Presse-fruits

Foire aux questions sur Adler AD 4123 Presse-fruits

Notre équipe d’assistance recherche des informations utiles sur les produits et des réponses aux questions fréquemment posées. Si vous trouvez une inexactitude dans notre foire aux questions, veuillez nous le faire savoir en utilisant notre formulaire de contact.

Produits connexes

Mode d’emploi

Adler AD 4128 Presse-fruits

Mode d’emploi

Adler AD 4132 Presse-fruits

Mode d’emploi

Adler AD 4124 Presse-fruits

Mode d’emploi

Adler AD 4129 Presse-fruits

Mode d’emploi

Adler AD 4125 Presse-fruits

Mode d’emploi

Adler AD 4127 Presse-fruits

Mode d’emploi

KitchenBrothers KB1004127 Presse-fruits

Mode d’emploi

Trebs 21137 Presse-fruits

Catégories associées