Mode d’emploi Adler AD 4128 Presse-fruits

Mode d’emploi

5

ASSEMBLING THE DEVICE

- Make sure that the grater and filter sieve are not too loose on the base and that they rotate evenly.

3. Close the safety locking handle (11).

4. Insert the large pulp container (3) correctly, place the juice jug on the opposite side of the juicer. NOTE: Before turning the device on,

make sure that all parts are properly installed.

2. Try to assemble and disassemble the unit for a few times before start working with the units.

1. Place the juice and pulp separating bowl (10) on the base (6).

2. Install the stainless steel grater and filter sieve (9) and then put the cover on (8).

- Be careful not to touch the sharp teeth on the bottom of the sieve.

- Make sure that the sieve sits properly on its base, so that the gear on the bottom of the sieve bowl engages the gear in the base.

2. Remove the cover (8).

TECHNICAL DATA

CLEANING AND MAINTENANCE

Voltage: 220-240V ~ 50/60Hz

1. Place the juicer on a smooth, flat and stable surface.

6. Always treat the filter (9) with care as it can be easily damaged.

USE

2. Wash the fruit or vegetables you want to use. In case they do not fit in the feeder (2), cut them into smaller pieces.

1. Turn the 3 position switch (5) to the '0' position. Unplug the power cord of the juicer from the power socket. Release the safety handle

(11).

3. Remove the juice and pulp separating bowl (10), then pull the stainless steel grater and filter basket (9) upwards.

NOTE: The machine is fitted with a safety switch (12). It prevents the juicer from being started unintentionally.

- Make sure that the stainless steel filter (9) has been thoroughly washed.

3. The cover (8) with the feeder (2), juice and pulp separating bowl (10), pulp container (3) and juice jar are dishwasher safe.

1. For easy cleaning - immediately after each use rinse removable parts under running water (to remove wet pulp). Allow parts to dry.

3. Make sure the juicer is assembled correctly.

6. Juice will start to drain into the jug and the pulp will start to collect in the container on the other side. To empty the pulp container (3),

switch off the juicer. Do not empty the container when the device is running and be careful not to overfill it, it may damage the device.

8. If discoloration does occur, the plastic parts can be soaked in 10% lemon juice and water or they can be cleaned with a non-abrasive

cleaner. To assist with cleaning soak the stainless steel grater and filter sieve (9) in hot soapy water for approximately 10 minutes

immediately after juicing is completed. If pulp is left to dry on the filter it may clog the fine pores of the filter mesh thereby lessening the

effectiveness of the juicer.

- Make sure the juice jug is placed under the spout (7).

2. After disassembling the unit all removable parts may be washed in hot soapy water.

7. Discoloration of the plastic may occur with strongly colored fruit and vegetables. To help prevent this, wash parts immediately after

use.

5. Do not soak the stainless steel grater and filter sieve (9) in bleach.

4. Put the plug into the power socket and turn on the device by setting the switch to the '1' or '2' position. Depending on the fruit or

vegetables used, use the speed switch (5) to change the speed to low (switch in '1' position) or high (switch in '2' position).

5. With the engine running, place the fruit (or vegetables) in the feeder (2). Use the pusher (1) to push them down. To get as much juice

as possible, push the fruit slowly.

NOTE: Never immerse the motor part in water or rinse under the tap.

9. Do not use abrasive pads or aggressive agents for cleaning.

DISASSEMBLY OF THE DEVICE

4. Wipe the motor base (6) with a damp cloth.

Nominal power: 1000W

Maximum power: 2000W

Maximum operation time: 3min - 20 minutes break

Two speeds mode: Hi - switch in position '2', Low - switch in position '1'.

Worn device should be returned to the appropriate point storage because it is dangerous in the device

its reuse and use. If in the device there are batteries you have to take out and give to the point stored separately.

ingredients may pose a threat to the environment. The electrical device should be handed over to limit

Please transfer cardboard packaging to waste paper. Pour the polyethylene bags (PE) into the plastic container

Évaluation

En savoir plus sur ce mode d’emploi

Nous comprenons qu’il est agréable d’avoir un mode d’emploi papier pour vos Adler AD 4128 Presse-fruits. Vous pouvez toujours télécharger le mode d’emploi depuis notre site Web et l’imprimer vous-même. Si vous souhaitez disposer d’un mode d’emploi original, nous vous recommandons de contacter Adler. Ils pourront peut-être fournir un mode d’emploi original. Recherchez-vous le mode d’emploi de votre Adler AD 4128 Presse-fruits dans une autre langue ? Choisissez votre langue préférée sur notre page d’accueil et recherchez le numéro de modèle pour voir si nous l’avons disponible.

Caractéristiques

Tous les modes d’emploi pour Adler Presse-fruits
Plus de modes d’emploi de Presse-fruits

Foire aux questions sur Adler AD 4128 Presse-fruits

Notre équipe d’assistance recherche des informations utiles sur les produits et des réponses aux questions fréquemment posées. Si vous trouvez une inexactitude dans notre foire aux questions, veuillez nous le faire savoir en utilisant notre formulaire de contact.

Produits connexes

Mode d’emploi

Adler AD 4125 Presse-fruits

Mode d’emploi

Adler AD 4124 Presse-fruits

Mode d’emploi

Adler AD 4127 Presse-fruits

Mode d’emploi

Adler AD 4129 Presse-fruits

Mode d’emploi

Adler AD 4132 Presse-fruits

Mode d’emploi

Adler AD 4123 Presse-fruits

Mode d’emploi

Robusta Tropico Presse-fruits

Mode d’emploi

KitchenBrothers KB683 Presse-fruits

Catégories associées