Mode d’emploi Bertazzoni CB36500X Table de cuisson

Mode d’emploi

3

ATTACHING THE HOTPLATE

To prevent liquids from leaking accidentally into the underlying storage space, the appliance is equipped with a special gasket. To apply

this gasket, carefully follow the instructions in Fig. 3. Lay out the protective sealing strips along the edges of the opening in the bench

top and carefully overlap the strip end. (See Fig. 3). insert the hotplate into the bench top opening. With a screwdriver assemble the

brackets A to the hotplate bottom by means of the screws B. (See Fig. 4). Slide the hooks into position and secure them with the screws.

Trim the part of the sealing strips which extend beyond the hotplate base

IMPORTANT INFORMATION CONCERNING THE INSTALLATION OF THE APPLIANCE

We inform the installer that this hob is of the Y type and thus it can be installed by itself, in an isolated position or inserted

between two kitchen units or between one kitchen unit and a wall. Furthermore the back wall and surrounding surfaces must

resist a temperature of 65 K.

To prevent the plastic layer which covers the kitchen unit from ungluing, the glue used to join the two surfaces together must

resist temperatures of up to 150 °C

The installation of the appliance must be carried out according to the norms in force of the country concerned and the

appliance must be installed in a well ventilated place.

This appliance is not equipped with devices to remove the products of combustion. The appliance must therefore be

connected following the norms for installation mentioned above. Special attention must be paid to the information below

regarding aeration and ventilation of the premises.

VENTILATION OF THE PREMISES

To guarantee that the appliance works correctly it is necessary that the place where the appliance is installed is continuously ventilated.

The volume of the premises must not be less than 25 m³ and the quantity of air needed must be based on the regular combustion of

gas and on the ventilation of the premises. The natural flow of air will take place through permanent openings made in the wall of the

premises to be ventilated: these openings will be connected to the outside and must have a minimum section of 100 cm² ( see Fig. 6 ).

These openings must be made in such a way that they cannot be obstructed.

POSITION AND VENTILATION

The cooking appliances that use gas must always remove the products of combustion via a hood linked to chimneys, chimney flues or

via a direct connection to the outside ( see Fig. 6A ). If it is not possible to fit a hood it is possible to use a fan, fitted on the window or

facing directly outside, which operates when the appliance is in use. ( see Fig. 6B ). In this way the norms in force of the country

concerned regarding the ventilation of premises are strictly followed.

CONNECTING THE APPLIANCE TO THE GAS SUPPLY

Before connecting the appliance to the gas supply you first need to remove the plastic protective plug for the gas supply which

is inserted under pressure in the gas inlet connection. To remove the plug simply unscrew it.

Then make sure that the details shown on the label on the lower part of the case are compatible with those of the gas supply.

A label on the last page of this manual and on the lower part of the case indicates the conditions for regulating the appliance:

type of gas and pressure used.

IMPORTANT: This appliance must be installed in accordance with the norms in force of the country concerned and it must only

be used in a well-ventilated place.

ATTENTION: Remember that the gas inlet connection for the appliance is threaded 1/2 gas cylindrical male in accordance with

the norms UNI-ISO 228-1. (Fig. 5)

ADAPTING TO DIFFERENT TYPES OF GAS

Before carrying out any maintenance work, disconnect the appliance from the gas and electric supply.

- CHANGING THE NOZZLES FOR USE WITH OTHER TYPES OF GAS:

To change the nozzles of the burners use the following procedure:

Lift up the burners and unscrew the nozzles ( Fig. 9) using an adjustable spanner of 7 mm and change the nozzles with those de

signed

for the new gas supply according to the information given in TABLE N° 2 shown below.

ATTENTION: After carrying out the changes described above, the technician must put the label corresponding to the new gas

supply on the appliance to take the place of the old label. This label is found in the bag containing spare nozzles.

TABLE N°2: Adapting to different types of gas APPLIANCE CATEGORY: II2H3+

Burner Type of Gas Pressure Nozzle Nominal Charge Reduced Charge Diameter

diameter by-pass 1/100mm

mbar 1/100mm g/h l/h Kw kcal/h kw kcal/h safety

Natural G20 20 77 - 95 1 860 0,3 258 27

Auxiliary Butane G30 28-30 50 73 - 1 860 0,3 258 27

Propane G31 37 50 71 - 1 860 0,3 258 27

Semi- Natural G20 20 101 - 167 1,75 1505 0,44 378 31

Rapid Butane G30 28 66 127 - 1,75 1505 0,44 378 31

Propane G31 37 66 125 - 1,75 1505 0,44 378 31

Natural G20 20 129 - 286 3 2580 0,75 645 42

Rapid Butane G30 28 87 218 - 3 2580 0,75 645 42

Propane G31 37 87 214 - 3 2580 0,75 645 42

Dual

Natural G20 20

In 70

- 476 5 4300 0,48 413

In 34

Out 2x110 Out 65

Butane G30 28

In 46

334 - 4,6 3956 0,48 413

In 34

Out 2x69 Out 65

Propane G31 37

In 46

338 - 4,6 3956 0,48 413

In 34

Out 2x69 Out 65

Évaluation

En savoir plus sur ce mode d’emploi

Nous comprenons qu’il est agréable d’avoir un mode d’emploi papier pour vos Bertazzoni CB36500X Table de cuisson. Vous pouvez toujours télécharger le mode d’emploi depuis notre site Web et l’imprimer vous-même. Si vous souhaitez disposer d’un mode d’emploi original, nous vous recommandons de contacter Bertazzoni. Ils pourront peut-être fournir un mode d’emploi original. Recherchez-vous le mode d’emploi de votre Bertazzoni CB36500X Table de cuisson dans une autre langue ? Choisissez votre langue préférée sur notre page d’accueil et recherchez le numéro de modèle pour voir si nous l’avons disponible.

Caractéristiques

Tous les modes d’emploi pour Bertazzoni Tables de cuisson
Plus de modes d’emploi de Tables de cuisson

Foire aux questions sur Bertazzoni CB36500X Table de cuisson

Notre équipe d’assistance recherche des informations utiles sur les produits et des réponses aux questions fréquemment posées. Si vous trouvez une inexactitude dans notre foire aux questions, veuillez nous le faire savoir en utilisant notre formulaire de contact.

Produits connexes

Mode d’emploi

Bertazzoni P604IC2B2NEE Table de cuisson

Mode d’emploi

Bertazzoni P905LPRONE Table de cuisson

Mode d’emploi

Bertazzoni P904ICHNE Table de cuisson

Mode d’emploi

Bertazzoni P903LMODX Table de cuisson

Mode d’emploi

Bertazzoni P604LMODX Table de cuisson

Mode d’emploi

Bertazzoni P604LPROGNE Table de cuisson

Mode d’emploi

Bertazzoni P604IC1B2NEE Table de cuisson

Mode d’emploi

Bertazzoni P604IM2G5NE Table de cuisson

Catégories associées