Mode d’emploi Black and Decker AS182 Fer à repasser

Besoin d'un mode d’emploi pour votre Black and Decker AS182 Fer à repasser ? Ci-dessous, vous pouvez consulter et télécharger gratuitement le mode d’emploi PDF en français. Ce produit a actuellement 4 questions fréquemment posées, 0 commentaires et 0 votes. Si ce n'est pas le mode d’emploi que vous souhaitez, veuillez nous contacter.

Votre produit est défectueux et le mode d’emploi n’offre aucune solution ? Rendez-vous à un Repair Café pour obtenir des services de réparation gratuits.

Mode d’emploi

Loading…

2
1
When using your iron, basic safety precautions should always be followed, including
the following:
READ ALL INSTRUCTIONS BEFORE USING.
Use iron only for its intended use.
To protect against a risk of electric shock, do not immerse the iron in water
or other liquid.
The iron should always be turned off (refer to "How to Use" section) before
plugging into or unplugging from an outlet. Never yank cord to disconnect from
outlet; instead grasp plug and pull to disconnect.
Do not allow cord to touch hot surfaces. Let iron cool completely before putting
away. Loop cord loosely around cord wrap when storing.
Always disconnect iron from electrical outlet when filling with or emptying
of water, and when not in use.
Do not operate iron with a damaged cord or if the iron has been dropped
or damaged. To avoid the risk of electric shock, do not disassemble the iron,
take it to a qualified serviceman for examination and repair. Or, call the appropriate
toll-free number listed on the cover of this manual. Incorrect reassembly can cause
a risk of electric shock when the iron is used.
Close supervision is necessary for any appliance being used by or near
children. Do not leave iron unattended while connected or on an ironing
board. Always position iron carefully to prevent it from falling if ironing board
is accidentally moved or cord is pulled. Always use heel rest.
Burns can occur from touching hot metal parts, hot water, or steam. Use
caution when you turn a steam iron upside down or use the surge of steam —
there may be hot water in the water tank. Avoid rapid movement of iron to
minimize hot water spillage.
SPECIAL INSTRUCTIONS
To avoid a circuit overload, do not operate another high-wattage appliance
on the same circuit.
If an extension cord is absolutely necessary, a 10-ampere and 120-volt,
or 6-ampere and 220-volt cord should be used. Cords rated for less amperage
may overheat. Care should be taken to arrange the cord so that it cannot be
pulled or tripped over.
IMPORTANT SAFETY
INSTRUCTIONS
SAVE THESE INSTRUCTIONS.
IMPORTANT DOWNY WRINKLE RELEASER
®
LIQUID INSTRUCTIONS
1. The physiological effects of the operation of the Downy Wrinkle Releaser
®
liquid, beneficial or otherwise, have not been investigated by Underwriters
Laboratories Inc.
2. First aid measures –
a. Eye Contact: Immediately flush eyes with plenty of water for at least
15 minutes. If irritation occurs or persists, have eyes examined or treated
by medical personnel.
b. Skin Contact: Remove contaminated clothing and footwear. Wash material
off skin with plenty of soap and water. Wash clothing and footwear before
reuse.
c. Ingestion: Drink milk or water to dilute. Induce vomiting only if advised
by physician or poison control center. Contact physician or poison control
center.
3. Personal precaution –
a. Avoid prolonged exposure.
b. Use rubber or neoprene, when needed, to prevent skin contact.
c. Use safety glasses recommended for handling spills.
4. Care and storage – Store in a cool, dry place. In poorly ventilated areas,
solvent fumes may be irritating. Masks rated for ammonia or organic solvents
may be desirable. Make sure you have good ventilation when handling liquid
spills.
5. Disposal Considerations – Disposal of this Downy Wrinkle Releaser
®
liquid
must be in accordance with local, state and federal regulations.
Soft-Touch Parts
Note: The soft-touch parts of this unit are free of natural rubber and latex.
They are safe for individuals allergic or sensitive to these materials.
POLARIZED PLUG (120V Models Only)
This appliance has a polarized plug (one blade is wider than the other). To reduce the
risk of electric shock, this plug will fit into a polarized outlet only one way. If the
plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a
qualified electrician. Do not attempt to modify the plug in any way.
TAMPER-RESISTANT SCREW
Warning: This appliance is equipped with a tamper-resistant screw to prevent
removal of the outer cover. To reduce the risk of fire or electric shock, do not attempt
to remove the outer cover. There are no user-serviceable parts inside. Repair should
be done only by authorized service personnel.
Note: If the power supply cord is damaged, it should be replaced by qualified
personnel or in Latin America by an authorized service center.
AS182Pub1000002000R1 8/3/05 2:29 PM Page 2
Télécharger mode d’emploi en Français (PDF, 5.47 MB)
(Tenez compte de l’environnement et imprimez ce manuel uniquement si c’est vraiment nécessaire)

Loading…

Évaluation

Dites-nous ce que vous pensez du Black and Decker AS182 Fer à repasser en laissant une note de produit. Vous voulez partager vos expériences avec ce produit ou poser une question ? Veuillez laisser un commentaire au bas de la page.
Etes-vous satisfait du Black and Decker AS182 Fer à repasser ?
Oui Non
Soyez le premier à évaluer ce produit
0 évaluations

Joignez-vous à la conversation sur ce produit

Ici, vous pouvez partager ce que vous pensez du Black and Decker AS182 Fer à repasser. Si vous avez une question, lisez d’abord attentivement le mode d’emploi. La demande d’un mode d’emploi peut être effectuée en utilisant notre formulaire de contact.

En savoir plus sur ce mode d’emploi

Nous comprenons qu’il est agréable d’avoir un mode d’emploi papier pour vos Black and Decker AS182 Fer à repasser. Vous pouvez toujours télécharger le mode d’emploi depuis notre site Web et l’imprimer vous-même. Si vous souhaitez disposer d’un mode d’emploi original, nous vous recommandons de contacter Black and Decker. Ils pourront peut-être fournir un mode d’emploi original. Recherchez-vous le mode d’emploi de votre Black and Decker AS182 Fer à repasser dans une autre langue ? Choisissez votre langue préférée sur notre page d’accueil et recherchez le numéro de modèle pour voir si nous l’avons disponible.

Caractéristiques

Marque Black and Decker
Modèle AS182
Catégorie Fers à repasser
Type de fichier PDF
Taille du fichier 5.47 MB

Tous les modes d’emploi pour Black and Decker Fers à repasser
Plus de modes d’emploi de Fers à repasser

Foire aux questions sur Black and Decker AS182 Fer à repasser

Notre équipe d’assistance recherche des informations utiles sur les produits et des réponses aux questions fréquemment posées. Si vous trouvez une inexactitude dans notre foire aux questions, veuillez nous le faire savoir en utilisant notre formulaire de contact.

Puis-je nettoyer le fond de mon fer à repasser avec un récureur ? Vérifié

Non, ça pourrait endommager le fond. Utilisez un chiffon humide ou une éponge douce pour le nettoyer.

Cela a été utile (363) En savoir plus

Quelles sont les différences entre un fer à vapeur et un fer à repasser ordinaire ? Vérifié

L’avantage principal d'un fer à vapeur est que la vapeur permet de défroisser plus facilement les plis. Quant à un fer à repasser ordinaire, il est bien plus léger et souvent moins cher.

Cela a été utile (296) En savoir plus

La semelle de mon fer à repasser est décolorée, puis-je encore repasser avec ? Vérifié

C’est possible, mais il y a un risque qu’il déteigne sur des vêtements de couleur claire.

Cela a été utile (245) En savoir plus

Puis-je repasser sur des boutons ? Vérifié

Non, cela endommagerait la semelle du fer et empêcherait le fer de fonctionner correctement. Ne repassez jamais sur des boutons, des fermetures éclair ou d’autres objets durs.

Cela a été utile (167) En savoir plus
Mode d’emploi Black and Decker AS182 Fer à repasser

Produits connexes

Catégories associées