Mode d’emploi Broan QP230WW Evolution 2 Hotte aspirante

Mode d’emploi

MODELS QP230BC • QP230BL • QP230SS • QP230WW

QP236BC • QP236BL • QP236SS • QP236WW

QP242BC • QP242BL • QP242SS • QP242WW

Page 2

CLEANING & MAINTENANCE

For performance, appearance, and health reasons, clean filter,

fan and grease-laden surfaces. Use only a clean cloth and mild

detergent solution on stainless and painted surfaces.

Clean all-metal filters in the dishwasher using a non-phosphate

detergent. Discoloration of the filter may occur if using phosphate

detergents, or as a result of local water conditions - but this will

not affect filter performance. This discoloration is not covered by

the warranty.

Clean the non-duct recirculating filter surfaces frequently with

a damp cloth and a mild detergent. DO NOT immerse filters in

water or put in dishwasher. The special “Clean Sense” feature

indicates when the filter is to be replaced. The blue and yellow

strips will blend to green when it is time to change the filter. The

“Clean Sense” feature works best when facing toward the cook-

ing surface. Change the non-duct recirculating filters every 6

months. For replacement non-duct recirculating filters - purchase

S99010353 or Model BPPF30 for 30 wide hoods”, S99010354

or Model BPPF36 for 36” wide hoods, or S99010360 or Model

BPPF42 for 42” wide hoods.

The motor is permanently lubricated and never needs oiling. If

the motor bearings make excessive or unusual noise, replace

the motor

with the

exact service motor. The impeller should also

be replaced.

Use 120 V, 50 W, shielded halogen bulbs - MR16 with GU10 base.

OPERATION

Always turn the hood ON before cooking in order to establish an

air flow in the kitchen. After turning off the range, let the hood run

for a few minutes to clear the air.

Operate the hood as follows:

LIGHT (3 pushbutton switches)

Turns light on to LOW setting.

Turns light on to MEDIUM setting.

Turns light on to HIGH setting.

Pressing the same light button again will turn lights OFF.

A light above each button indicates light setting.

FAN (3 pushbutton switches)

Turns fan on to LOW speed.

Turns fan on to MEDIUM speed.

Turns fan on to HIGH speed.

Pressing the same fan button again will turn fan OFF.

A light above each button indicates fan speed.

NOTE

This hood utilizes an offset blower design to achieve greater

performance and lower sound levels. As a result, you may notice

that cooking impurities are more attracted to one side or appear

to be pulled-in faster than they appear on the opposite side. This

is completely normal. The hood has been designed and tested

to provide good capture of cooking impurities and odors under

all normal cooking conditions regardless of the cooking location

on the cooktop. Please note that cooking on the rear burners will

always result in the best capture of cooking impurities, regardless

of the hood design.

HEAT SENTRY SYSTEM

This range hood is equipped with an advanced Heat Sentry sys-

tem that monitors for excessive temperature and automatically

adjusts the fan to the appropriate setting.

1) If the fan is on, the Heat Sentry system will increase the fan

setting when the temperature is elevated. If the temperature con-

tinues to rise, the Heat Sentry system will continue to increase

the fan setting until the temperature is stabilized or reduced. The

flashing light above the fan button shows the Heat Sentry system

fan setting. Once the temperature has reduced, the Heat Sentry

system will change the fan to the original setting.

2) If the fan is off, the Heat Sentry system will automatically turn

the fan on to its highest speed when the temperature is above

normal. When the Heat Sentry system is on, the light above the

high speed fan button will flash on and off. After the temperature

has lowered to normal, the fan speed will be reduced until the

temperature has stabilized, then the fan will turn off.

CONTENTS

GREASE

FILTERS

(2 - FOR 30” & 36” HOODS)

3 - FOR 42” HOODS)

(1) 3¼” X 10”

DAMPER / DUCT

CONNECTOR

(1) 7” ROUND

DUCT

CONNECTOR

(4)

HALOGEN

BULBS

(1)

BULB

SUCTION

CUP TOOL

(1) PARTS BAG CONTAINING:

(3)

WIRE

NUTS

(1)

NON-DUCT

DIVERTER

INCLUDED WITH THE HOOD:

(9)

#8 X 1/4”

DUCT

CONNECTOR

SCREWS

(5)

#10 X 5/8”

RD. HD.

MOUNTING

SCREWS

(2)

#8 X 5/16”

MACHINE

SCREWS

&

(2)

#8 WASHERS

FOR NON-DUCT

DIVERTER

Note: Canadian version does not have this function.

Évaluation

En savoir plus sur ce mode d’emploi

Nous comprenons qu’il est agréable d’avoir un mode d’emploi papier pour vos Broan QP230WW Evolution 2 Hotte aspirante. Vous pouvez toujours télécharger le mode d’emploi depuis notre site Web et l’imprimer vous-même. Si vous souhaitez disposer d’un mode d’emploi original, nous vous recommandons de contacter Broan. Ils pourront peut-être fournir un mode d’emploi original. Recherchez-vous le mode d’emploi de votre Broan QP230WW Evolution 2 Hotte aspirante dans une autre langue ? Choisissez votre langue préférée sur notre page d’accueil et recherchez le numéro de modèle pour voir si nous l’avons disponible.

Caractéristiques

Tous les modes d’emploi pour Broan Hottes aspirantes
Plus de modes d’emploi de Hottes aspirantes

Foire aux questions sur Broan QP230WW Evolution 2 Hotte aspirante

Notre équipe d’assistance recherche des informations utiles sur les produits et des réponses aux questions fréquemment posées. Si vous trouvez une inexactitude dans notre foire aux questions, veuillez nous le faire savoir en utilisant notre formulaire de contact.

Produits connexes

Mode d’emploi

Broan QP230BL Evolution 2 Hotte aspirante

Mode d’emploi

Broan QP242BL Evolution 2 Hotte aspirante

Mode d’emploi

Broan QP236BL Evolution 2 Hotte aspirante

Mode d’emploi

Broan QP230BC Evolution 2 Hotte aspirante

Mode d’emploi

Broan QP236WW Evolution 2 Hotte aspirante

Mode d’emploi

Broan QP236BC Evolution 2 Hotte aspirante

Mode d’emploi

Broan QP242SS Evolution 2 Hotte aspirante

Mode d’emploi

Broan QP242WW Evolution 2 Hotte aspirante

Catégories associées