Mode d’emploi Caliber MCD450M Autoradio

Mode d’emploi

ENGLISH

3

ENGLISH

2

DISC PLAY

PRECAUTIONS

• Use only in a 12-volt DC negative-ground electrical system.

• Disconnect the vehicle's negative battery terminal while mounting and connecting the

unit.

• When replacing the fuse, be sure to use one with an identical amperage rating.

•Using a fuse with a higher amperage rating may cause serious damage to the unit.

•DO NOT attempt to disassemble the unit. Laser beams from the optical pickup are dan-

gerous to the eyes.

• Make sure that pins or other objects do not get inside the unit; they may cause mal-

functions, or create safety hazards such as electrical shock or laser beam exposure.

• If you have parked the car for a long time in hot or cold weather, wait until the tem-

perature in the car become normal before operating the unit.

• Keep the volume at a level at which you can hear outside warning sounds (horns

sirens, etc.).

CD NOTES

• Playing a defective or dusty CD can cause dropouts in sound.

• Hold CDs as illustrated.

• DO NOT touch the unlabeled side.

• DO NOT attach any seal, label or data protection sheet to either side of a disc.

• DO NOT expose a CD to direct sunlight or excessive heat.

• Wipe a dirty CD from the center outward with a cleaning cloth.

•Never use solvents such as benzine or alcohol.

• This unit cannot play 3-inch ( 8cm ) CDs.

• NEVER insert a 3-inch CD contained in the adapter

or an irregularly shaped CD.

• The unit may not be able to eject it, resulting in a

malfunction.

BEFORE OPERATION

•DO NOT raise the volume level too much, as this

will block outside sounds, making driving dangerous.

• Stop the car before performing any complicated

operation.

CAUTION

DO NOT open covers and do not repair by yourself.

Consult the dealer or an experienced technician for help.

Installation procedures

First complete the electrical connections, and then

check them for correctness.

Anti-Theft System

This unit is equipped with a detachable panel.

Removing this panel makes the radio totally inoperable.

Removing the panel

1. Switch off the power of the unit.

2. Remove the detachable panel.

3. Gently press the button of the case and open the

cover. Place the panel into the case and take it with you

when you leave the car.

Install detachable panel

1.Fix right part of face plate in the right part of panel slot

of the unit.

2.Press down the left side of the face plate until it clicks

into the panel slot of the unit.

Remove the unit

Switch of the power of the unit.

1. Remove the panel and the trim plate.

2. Insert both T-Keys into hole in front of the set until

they lock.

3. Pull out the unit.

5. BASIC OPERATIONS

1) PANEL REMOVE BUTTON

Press this button to remove the control panel.

2) POWER ON/OFF BUTTON

Press POWER button or any other button on the front of the radio (except

Open/Eject)to turn the unit on. Press POWER button again to turn the unit off.

18) MODE BUTTON (MODE)

Press MODE button to select a different mode of operation as indicated on the display

panel.Available modes include Tuner, CD, MP3 and Aux in mode .

10) MUTE BUTTON (MUTE)

Press the mute button momentarily to mute the audio volume, and "Mute" will flash in

the display. Press the mute button again to restore volume to the previous setting.

12) VOLUME KNOB

To increase the volume rotate the volume knob clockwise, to decrease the volume rota-

te the volume knob counterclockwise.

13) AUDIO BUTTON (AUDIO)

Press the AUDIO button, the display will be displayed first option is Volume, followed by

Bass,Treble, Balance, Fader and back to Volume.

When adjusting audio functions, the unit will automatically exit audio control mode

after 5 seconds of inactivity. Use the volume knob to adjust the settings.

Press the AUDIO button for more than 3 seconds, the display will be displayed as cycli-

cal mode of following functions:TA SEEK or ALARM, PI SOUND or MUTE, RETUNE L

or S, MASK DPI or ALL, BEEP 2’nd and ALL or OFF.

TA SEEK or ALARM

Rotate the knob to choose TA ALARM or TA SEEK mode,When TA is turned on and

no traffic program identification code has been received during the specified time, no

TA/TP is displayed and according to the MENU SELECT, alarm is set off, or TA SEEK is

activated.

TA ALARM mode: NO TA/TP is displayed and alarm is set off.

TA SEEK mode:TA SEEK is activated.

PI SOUND or MUTE

PI SOUND:When above different PI sound (DIP) is heard once in a while, the DIP’s

sound will be heard for less than 1 second.

PI MUTE:When above different PI sound (DIP) is heard once in a while, a mute sound

will be heard for less than 1 second.

RETUNE L or S

The initial time of automatic TA search or PI search mode is selected.When PI infor-

mation is not caught for retune time, the radio start to retune to the next same PI

station.When the same PI station does not catch 1 cyclic search, the radio start to

retune to the next same PI station.

RETUNE L mode: Selected as 90 seconds

RETUNE S mode: Selected as 30 seconds

MASK DPI or ALL

Rotate the knob to choose MASK DPI or MASK ALL mode.

MASK DPI mode: Only the AF which has different program identification is masked.

MASK ALL mode:The AF which has different program identification and NO RDS sig-

nal with high field strength is masked.

BEEP 2’ND,ALL or OFF

BEEP 2’ND mode:The beep is only generated when an allottes double key is pressed

long (1 sec.).

BEEP ALL mode:The beep is generated when every key is pressed.

BEEP OFF mode:The beep is off.

9) DISPLAY (DISP)

Pressing the “DISP” key will display the following modes;

In case of receiving a RDS station:

Tuner mode PS – CT – FREQ – PTY

CD/MP3 player mode CDP – CT – PS – FREQ – PTY

In case of receiving NON RDS station

Tuner mode NO CLOCK – FREQ – NO PTY

CD/MP3 player mode CDP – CT – FREQ – NO PTY

6. TUNER OPERATION

6) BAND/LOUDNESS BUTTON (BAND/LOUD)

Press BAND to change between FM 1, FM 2, FM 3 and MW.

Press BAND for more than 2 seconds to start loudness.

19) TUNING UP/DOWN BUTTON

Manual Tuning

Press the Up Tuning or Down Tuning button for more than 3 seconds to move the radio

frequency number up or down one step.

Auto Seek Tuning

Press the Up Tuning or Down Tuning button for less than 3 seconds to move to next

station automatically.

1. Insert mounting bracket into the

dashboard, and bend the mounting

tabs out with a screwdriver. (Make

sure that lock lever is flush with

the mounting bracket. Not projec-

ting outward)

2. Secure the rear of the unit After

fixing mounting bolt and power

connector, fix the rear of the unit

to the car body by rubber cushion.

3. Insert trimplate

MCD 450M manual def 10-07-2006 11:51 Pagina 2

Évaluation

En savoir plus sur ce mode d’emploi

Nous comprenons qu’il est agréable d’avoir un mode d’emploi papier pour vos Caliber MCD450M Autoradio. Vous pouvez toujours télécharger le mode d’emploi depuis notre site Web et l’imprimer vous-même. Si vous souhaitez disposer d’un mode d’emploi original, nous vous recommandons de contacter Caliber. Ils pourront peut-être fournir un mode d’emploi original. Recherchez-vous le mode d’emploi de votre Caliber MCD450M Autoradio dans une autre langue ? Choisissez votre langue préférée sur notre page d’accueil et recherchez le numéro de modèle pour voir si nous l’avons disponible.

Caractéristiques

Tous les modes d’emploi pour Caliber Autoradios
Plus de modes d’emploi de Autoradios

Foire aux questions sur Caliber MCD450M Autoradio

Notre équipe d’assistance recherche des informations utiles sur les produits et des réponses aux questions fréquemment posées. Si vous trouvez une inexactitude dans notre foire aux questions, veuillez nous le faire savoir en utilisant notre formulaire de contact.

Produits connexes

Mode d’emploi

Caliber MCD170 Autoradio

Mode d’emploi

Caliber MCD300M Autoradio

Mode d’emploi

Caliber MCD261M Autoradio

Mode d’emploi

Caliber MCD570 Autoradio

Mode d’emploi

Caliber MCD370 Autoradio

Mode d’emploi

Caliber MCD560M Autoradio

Mode d’emploi

Caliber MCD250M Autoradio

Mode d’emploi

Caliber MCD220 Autoradio

Catégories associées