Mode d’emploi Candy CDI 2012-S Lave-vaisselle

Mode d’emploi

* The water softener unit is set in the

factory at level 3, as this is suitable for

the majority of users.

According to the degree of hardness of

your water, regulate the softener unit in the

following way:

IMPORTANT

The dishwasher must be ALWAYS

off before start this procedure.

1. When the dishwasher is off, OPEN

the door.

2. Hold down the FIRST and the THIRD

"PROGRAMME" button (from the right)

while simultaneously pushing the

"ON/OFF" button.

3. Release the buttons when some

"PROGRAMME SELECTION" indicator

lights up.

4. Press the "PROGRAMME" button for

the required water softener level (each

time the button is pressed a light will go

on). For level 5, press the "HALF

LOAD" button.

5. Turn off the dishwasher pressing the

"ON/OFF" button to confirm the new

setting.

WARNING!

If any problem occurs, turn the

dishwasher off by pressing the

"ON/OFF" button and start the

procedure again from the beginning

(STEP 1).

15

WATER SOFTENER UNIT

Depending on the source of the supply,

water contains varying amounts of limestone

and minerals which are deposited on the

dishes leaving whitish stains and marks.

The higher the level of these minerals

present in the water, the harder the water is.

The dishwasher is fitted with a water

softener unit which, through the use of

special regenerating salt, supplies

softened water for washing the dishes.

The degree of hardness of your water can

be obtained from your water supply

company.

Regulating the water softener

The softener unit can treat water with a

hardness of up to 90°fH (French grading)

or 50°dH (German grading) through 6

different settings.

The table below lists different degrees of

water hardness with the corresponding

setting for the softener unit.

Level

ºfH

(French

grading)

ºdH

(German

grading)

NO

YES

YES

YES

YES

YES

Indicator light

1

Indicator light

1

Indicator lights

1,2

Indicator lights

1,2,3

Indicator lights

1,2,3,4

Indicator lights

1,2,3,4,5

Water

hardness

Water

softener

setting

Use of

regenerating

salt

0

1

2

*3

4

5

0-5

6-15

16-30

31-45

46-60

61-90

0-3

4-9

10-16

17-25

26-33

34-50

“PROGRAMME”

buttons

Indicator lights 5 4 3 2 1

5

4 3 2

0

1

“HALF LOAD”

option button

Levels

“ON/OFF” button

14

■ Press the "DELAY START" button to

set another delayed start time (the

corresponding indicator light will turn on).

■ A new programme can be set after a

delayed time has been changed or

cancelled or an option button has selected

or deselected.

Alarm mute for the PROGRAMME

END

The alarm for the programme end may be

muted as follows:

■ With the dishwasher off, hold down the

"HALF LOAD" button for few seconds

while simultaneously pushing the

"ON/OFF" button, releasing them only

after the alarm sound.

■ Press the "HALF LOAD" button again:

the relevant indicator light (turned on to

indicate that the alarm is activated) will

flash (to indicate that the alarm is off).

■ Wait for the alarm to sound to indicate

that the settings were saved.

■ To turn the alarm on again, follow the

same procedure.

Fault signals

If malfunctions or faults occur when a

programme is running the indicator light

that corresponds to the selected cycle

(2 indicator lights for the "COLD RINSE"

programme) will flash rapidly and the alarm

sounds.

In this event, turn the dishwasher off by

pressing the "ON/OFF" button.

After checking to make sure the water

inlet hose tap is open, that the drain

hose is not bent and that the siphon or

filters are not clogged, set the selected

programme again.

If the anomaly persists, contact Customer

Service Department.

IMPORTANT

This dishwasher is equipped with an

anti-overflow safety device which will

automatically discharge any excess

water should a problem occur.

WARNING!

To ensure the correct operation of

the anti-overflow safety device, we

recommend that the dishwasher is

not moved or tilted during operation.

If however it is necessary to tilt or

move the dishwasher, please ensure

that the washing cycle is complete

and that there is no remaining water

inside the dishwasher.

Évaluation

En savoir plus sur ce mode d’emploi

Nous comprenons qu’il est agréable d’avoir un mode d’emploi papier pour vos Candy CDI 2012-S Lave-vaisselle. Vous pouvez toujours télécharger le mode d’emploi depuis notre site Web et l’imprimer vous-même. Si vous souhaitez disposer d’un mode d’emploi original, nous vous recommandons de contacter Candy. Ils pourront peut-être fournir un mode d’emploi original. Recherchez-vous le mode d’emploi de votre Candy CDI 2012-S Lave-vaisselle dans une autre langue ? Choisissez votre langue préférée sur notre page d’accueil et recherchez le numéro de modèle pour voir si nous l’avons disponible.

Caractéristiques

Tous les modes d’emploi pour Candy Lave-vaisselle
Plus de modes d’emploi de Lave-vaisselle

Foire aux questions sur Candy CDI 2012-S Lave-vaisselle

Notre équipe d’assistance recherche des informations utiles sur les produits et des réponses aux questions fréquemment posées. Si vous trouvez une inexactitude dans notre foire aux questions, veuillez nous le faire savoir en utilisant notre formulaire de contact.

Produits connexes

Mode d’emploi

Candy CDPN 4S603PX/E Lave-vaisselle

Mode d’emploi

Candy CDSN 1L350PB Lave-vaisselle

Mode d’emploi

Candy CLVI 2D520PB/E Lave-vaisselle

Mode d’emploi

Candy CDSN 4D622PX/E Lave-vaisselle

Mode d’emploi

Candy CF 6B4S1PX Lave-vaisselle

Mode d’emploi

Candy CDIMN 4S622PS Lave-vaisselle

Mode d’emploi

Candy CDP 2L949W Lave-vaisselle

Mode d’emploi

Candy CF 4E7L0X Lave-vaisselle

Catégories associées