Mode d’emploi Candy CMD 95 X Hotte aspirante

Mode d’emploi

ENGLISH

DESCRIPTION

The hood may be installed in the filtering or the ducting version.

Filtering version (Fig. 1): The hood aspirates the kitchen air saturated with fumes and odours, purifies it through the

grease filters and charcoal filters and returns clean air into the room. For constant efficiency, the charcoal filters must

be replaced periodically.

Ducting version (Fig. 2): The hood aspirates the kitchen air saturated with fumes and odours, passes it through the

grease filters and expels it to the outside through an outlet pipe. With this version the charcoal filters are not required.

Decide from the outset on the type of installation (filtering or ducting). For greater efficiency, we recommend you

install the hood in the ducting version (if possible).

INSTALLATION

ATTENTION: Two persons are required for proper installation; the unit should be installed by a qualified

operator.

To facilitate installation, before starting remove the grease filter/s: press inward on the clamp at the handle and

pull the filter downward (Fig. 3).

INSTALLATION IN DUCTING VERSION:

Before fixing, the

outlet pipe for air evacuation to the outside must be installed. Use an outlet pipe with: –

minimum indispensable length; – minimum possible bends (maximum angle of bend: 90°); – certified material (ac-

cording to the State); – an as smooth as possible inside. It is also advisable to avoid any drastic changes in pipe

cross-section (recommended diameter: 150 mm). For air evacuation to the outside, follow all the other instructions

given on the “Warnings” sheet.

Prepare the power supply within the telescopic chimney (for the electrical connection, follow all the other instruc-

tions on the “Warnings” sheet).

1. Installation on the wall (Fig. 4): Using the special drilling template, drill the required holes in the wall. As

previously specified in the chapter “Warning” remember there must be a minimum of 650 mm between the bottom

edge of the hood and the stop of the stove. Secure the metal bracket (B) to the wall using the screws and plugs

(bracket, screws and plugs are all supplied with the unit). Use the 2 triangles cut into the bracket to position it

precisely along the vertical axis of the hood. Then set the hood onto the bracket (Fig. 5). Adjust the horizontal

position, shifting the hood to the right or left as needed lining it up with the wall units. If the height of the hood also

requires adjustment, use the special regulation screws (C) (supplied). Once regulation has been completed, finish

securing the hood with 4 more screws (D): mark the points for the 4 holes on the wall, remove the hood and drill (8mm

diameter holes); then use the plugs and screws to complete installation.

2. Installation with rear panel (upon request) - Fig. 6: The rear panel is positioned at the top of the stove,

flush against the wall. Rest the lower edge of the panel behind the stove and anchor the upper edge to the wall using

the two holes found on the panel. Insert the screws and plugs provided (A). The unit is secured to the rear panel

as though it were being installed on the wall: use the supplied metal bracket (B) and the screws and plugs supplied

with the panel.

3. Fixing the telescopic flues: - Adjust the width of the support bracket (E) of the telescopic flue by means

of the screws (F) as shown in Fig. 7. - Then, by means of the screw anchors and screws (G) provided, fix the bracket

to the ceiling in such a way that it is positioned along the axis with your hood. - Connect the air outlet pipe to the

air vent of the hood. - Use a flexible pipe and lock it to the air vent of the hood with a metal hose clamp - Fig. 8 (pipe

and clamp are not provided). - For exhaust hoods, turn the upper pipe over so that the air exhaust grid is in the lower

section (Fig. 9). Plug in the hood. Insert the extension pipes setting them on the hood; extend the upper pipe to the

ceiling and secure with the 2 screws (H) - Fig. 10.

INSTALLATION IN FILTERING VERSION:

Prepare the power supply within the telescopic chimney (for the electrical connection, follow all the other instruc-

tions on the “Warnings” sheet).

Fixing to the wall: for fixing to the wall refer to the instructions for the ducting version (see point 1, 2), then

continue with the instructions below.

Fixing the telescopic flues: - Adjust the width of the support bracket (E) of the telescopic flue by means of the

screws (F) as shown in Fig. 7. - Then, by means of the screw anchors and screws (G) provided, fix the bracket to

the ceiling in such a way that it is positioned along the axis with your hood. - Mount the flange on the hood in

correspondence to the air outlet point (Fig. 11). – Take the air baffle and fit a flexible pipe to it (125 mm diameter)

locking it with a metal hose clamp (pipe and clamps are not provided). Fit the air baffle to the upper flue (Fig. 12)

with 4 screws. Take the 2 assembled extension pipes and set them on the hood; extend the upper pipe to the ceiling

and secure with the 2 screws (H) - Fig. 10. Extend the lower pipe taping it in place and then connect the flexible

pipe to the hood reduction (Fig. 13). Plug in the hood. Extend the lower pipe downward setting it against the hood.

Install the carbon filter by pressing the 2 tabs on the filter down into the special housing (Fig. 14) and rotating upward.

Évaluation

En savoir plus sur ce mode d’emploi

Nous comprenons qu’il est agréable d’avoir un mode d’emploi papier pour vos Candy CMD 95 X Hotte aspirante. Vous pouvez toujours télécharger le mode d’emploi depuis notre site Web et l’imprimer vous-même. Si vous souhaitez disposer d’un mode d’emploi original, nous vous recommandons de contacter Candy. Ils pourront peut-être fournir un mode d’emploi original. Recherchez-vous le mode d’emploi de votre Candy CMD 95 X Hotte aspirante dans une autre langue ? Choisissez votre langue préférée sur notre page d’accueil et recherchez le numéro de modèle pour voir si nous l’avons disponible.

Caractéristiques

Tous les modes d’emploi pour Candy Hottes aspirantes
Plus de modes d’emploi de Hottes aspirantes

Foire aux questions sur Candy CMD 95 X Hotte aspirante

Notre équipe d’assistance recherche des informations utiles sur les produits et des réponses aux questions fréquemment posées. Si vous trouvez une inexactitude dans notre foire aux questions, veuillez nous le faire savoir en utilisant notre formulaire de contact.

Produits connexes

Mode d’emploi

Candy CCE90NX Hotte aspirante

Mode d’emploi

Candy CCE1104/1X Hotte aspirante

Mode d’emploi

Candy CBG6250/1X Hotte aspirante

Mode d’emploi

Candy CFT 161 FN Hotte aspirante

Mode d’emploi

Candy CBG625/1X Hotte aspirante

Mode d’emploi

Candy CFT610/5S/1 Hotte aspirante

Mode d’emploi

Candy CDG6CBG Hotte aspirante

Mode d’emploi

Candy CBT 92 X Hotte aspirante

Catégories associées