Mode d’emploi Chicago Pneumatic CP7263 Ponceuse delta

Mode d’emploi

CP7263, CP7264, CP7266, CP7267 Series

Random orbital sander

Original Instructions

Copyright 2011, Chicago Pneumatic Tool Co. LLC

All rights reserved. Any unauthorized use or copying of the

contents or part thereof is prohibited. This applies in particular to

trademarks, model denominations, part numbers and drawings.

Use only authorized parts. Any damage or malfunction caused

by the use of unauthorized parts is not covered by Warranty or

Product Liability.

Noise & Vibration Declaration*

Sound pressure level 78 dB(A), uncertainty 3 dB(A), in

accordance with EN ISO 15744. For sound power, add 11

dB(A).

Vibration value,

Vibration level a Uncertainty k (m/s²)

CP7263E 9.4 3

CP7263CVE 8.9 2.1

CP7264E 9.2 3.4

CP7264CVE 7.2 2.1

CP7266E 7.3 2.9

CP7266CVE 7.7 2.8

CP7267E 9.6 3.2

CP7267CVE 9 3.7

re. ISO 28927-3.

Declaration of noise and vibration emission

All values are current as of the date of this publication. For the latest

information please visit cp.com.

These declared values were obtained by laboratory type testing in

accordance with the stated standards and are suitable for comparison

with the declared values of other tools tested in accordance with the

same standards. These declared values are not adequate for use in risk

assessments and values measured in individual work places may be

higher. The actual exposure values and risk of harm experienced by an

individual user are unique and depend upon the way the user works, the

workpiece and the workstation design, as well upon the exposure time

and the physical condition of the user.

We, Chicago Pneumatic, cannot be held liable for the consequences

of using the declared values, instead of values reecting the actual

exposure, in an individual risk assessment in a work place situation over

which we have no control.

This tool may cause hand-arm vibration syndrome if its use is not

adequately managed. An EU guide to managing hand-arm vibration

can be found at www.pneurop.eu/uploads/documents/pdf/PN3-02-

NV_Declaration_info_sheet_0111.pdf

We recommend a programme of health surveillance to detect early

symptoms which may relate to noise or vibration exposure, so that

management procedures can be modied to help prevent future

impairment.

MANUFACTURER’S LIMITED WARRANTY

Limited Warranty: The “Products” of the Chicago Pneumatic Tool

Co. LLC (“CP”) are warranted to be free from defects in material and

workmanship for one year from the date of purchase. This Warranty

applies only to Products purchased new from CP or its authorized dealers.

Of course, this Warranty does not apply to products which have been

abused, misused, modied, or repaired by someone other than CP or its

Authorized Service Representatives. If a CP Product proves defective in

material or workmanship within one year after purchase, return it to any

CP Factory Service Center or Authorized Service Center for CP tools,

transportation prepaid, enclosing your name and address, adequate

proof of date of purchase, and a short description of the defect. CP will,

at its option, repair or replace defective Products free of charge. Repairs

or replacements are warranted as described above for the remainder of

the original warranty period. CP’s sole liability and your exclusive remedy

under this Warranty is limited to repair or replacement of the defective

Product. (There Are No Other Warranties Expressed Or Implied And

CP Shall Not Be Liable For Incidental, Consequential, Or Special

Damages, Or Any Other Damages, Costs Or Expenses Excepting

Only The Cost Or Expense Of Repair Or Replacement As Described

Above.)

INSTRUCTION MANUAL

Machine Type:

Pneumatic tool equipped with a exible disc tted with

abrasive paper for sanding - No other use is permitted.

Air Supply Requirements

1. Supply tool with 90 psig (6.3 bar) of clean, dry air. Higher

pressure drastically reduces tool life.

2. Connect tool to air line using pipe, hose and tting sizes

shown in the diagram below.

3. Do not install a quick coupler directly into the sander

throttle handle.

Lubrication

Use an air line lubricator with SAE #10 oil, adjusted to two

drops per minute. If an air line lubricator cannot be used,

add air motor oil to the inlet once a day.

Maintenance

1. Disassemble and inspect tool every three months if the tool

is used every day. Replace damaged or worn parts.

2. High wear parts are underlined in the parts list.

3. To keep downtime to a minimum, the following service kits

are recommended: Tune-Up Kit: 8940163459

Technical Data

Pad size:

CP7263 Series: 3”x4-1/4” (75x110mm)

CP7264 Series: 2-3/4”x7-3/4” (70x198mm)

CP7266 Series: 3-1/4”x5” (80x130mm)

CP7267 Series: 3-7/8”-5-5/8” (100x144mm) delta shape

Free speed; 10 000 RPM

Air pressure 90 psi (6.3 bar)

Air comsumption; 18 cfm - 8,5 l/s

English

EN

Évaluation

En savoir plus sur ce mode d’emploi

Nous comprenons qu’il est agréable d’avoir un mode d’emploi papier pour vos Chicago Pneumatic CP7263 Ponceuse delta. Vous pouvez toujours télécharger le mode d’emploi depuis notre site Web et l’imprimer vous-même. Si vous souhaitez disposer d’un mode d’emploi original, nous vous recommandons de contacter Chicago Pneumatic. Ils pourront peut-être fournir un mode d’emploi original. Recherchez-vous le mode d’emploi de votre Chicago Pneumatic CP7263 Ponceuse delta dans une autre langue ? Choisissez votre langue préférée sur notre page d’accueil et recherchez le numéro de modèle pour voir si nous l’avons disponible.

Caractéristiques

Tous les modes d’emploi pour Chicago Pneumatic Ponceuses delta
Plus de modes d’emploi de Ponceuses delta

Foire aux questions sur Chicago Pneumatic CP7263 Ponceuse delta

Notre équipe d’assistance recherche des informations utiles sur les produits et des réponses aux questions fréquemment posées. Si vous trouvez une inexactitude dans notre foire aux questions, veuillez nous le faire savoir en utilisant notre formulaire de contact.

Produits connexes

Mode d’emploi

Chicago Pneumatic CP7266 Ponceuse delta

Mode d’emploi

Chicago Pneumatic CP7264 Ponceuse delta

Mode d’emploi

Chicago Pneumatic CP7267 Ponceuse delta

Mode d’emploi

Skil 3720 CD Ponceuse delta

Mode d’emploi

Kress CDS 6425 EXL Ponceuse delta

Mode d’emploi

Pattfield PE-260 DS Ponceuse delta

Mode d’emploi

Parkside IAN 100087 Ponceuse delta

Mode d’emploi

Dexter Power 300DS2.5 Ponceuse delta

Catégories associées