Mode d’emploi DeWalt DCG416VSB Meuleuse angulaire

Mode d’emploi

7

ENGLISH

Safety Warnings Specific for Wire Brushing

Operations:

a ) Be aware that wire bristles are thrown by the

brush even during ordinary operation. Do not

overstress the wires by applying excessive load to

the brush. The wire bristles can easily penetrate light

clothing and/orskin.

b ) If the use of a guard is specified for wire brushing,

do not allow any interference of the wire wheel

or brush with the guard. Wire wheel or brush

may expand in diameter due to work load and

centrifugalforces.

Safety Warnings Specific for Sanding

Operations:

a ) Use proper sized sanding disc paper. Follow

manufacturers recommendations, when selecting

sanding paper. Larger sanding paper extending

too far beyond the sanding pad presents a laceration

hazard and may cause snagging, tearing of the disc

orkickback.

b ) Do not position your body in line with and behind

the rotating wheel. When the wheel, at the point of

operation, is moving away from your body, the possible

kickback may propel the spinning wheel and the power

tool directly atyou.

c ) When the wheel is binding or when interrupting

a cut for any reason, switch off the power tool

and hold it motionless until the wheel comes to

a complete stop. Never attempt to remove the

cut‑off wheel from the cut while the wheel is in

motion otherwise kickback may occur. Investigate

and take corrective action to eliminate the cause of

wheelbinding.

d ) Do not restart the cutting operation in the

workpiece. Let the wheel reach full speed and

carefully re‑enter the cut. The wheel may bind,

walk up or kickback if the power tool is restarted in

theworkpiece.

e ) Support panels or any oversized workpiece to

minimize the risk of wheel pinching and kickback.

Large workpieces tend to sag under their own weight.

Supports must be placed under the workpiece near the

line of cut and near the edge of the workpiece on both

sides of thewheel.

f ) Use extra caution when making a “pocket cut”

into existing walls or other blind areas. The

protruding wheel may cut gas or water pipes, electrical

wiring or objects that can causekickback.

g ) Do not attempt to do curved cutting. Overstressing

the wheel increases the loading and susceptibility to

twisting or binding of the wheel in the cut and the

possibility of kickback or wheel breakage, which can

lead to seriousinjury.

Additional Safety Warnings Specific for

Cutting‑Off Operations:

a ) Do not “jam” the cut‑off wheel or apply excessive

pressure. Do not attempt to make an excessive

depth of cut. Overstressing the wheel increases the

loading and susceptibility to twisting or binding of

the wheel in the cut and the possibility of kickback or

wheelbreakage.

Safety Warnings Specific for Grinding and

Cutting‑Off Operations:

a ) Use only wheel types that are specified for your

power tool and the specific guard designed for

the selected wheel. Wheels for which the power tool

was not designed cannot be adequately guarded and

areunsafe.

b ) The grinding surface of center depressed

wheels must be mounted below the plane of

the guard lip. An improperly mounted wheel that

projects through the plane of the guard lip cannot be

adequatelyprotected.

c ) The guard must be securely attached to the power

tool and positioned for maximum safety, so the

least amount of wheel is exposed towards the

operator. The guard helps to protect the operator

from broken wheel fragments, accidental contact with

wheel and sparks that could igniteclothing.

d ) Wheels must be used only for specified

applications. For example: do not grind with the

side of cut‑off wheel. Abrasive cut‑off wheels are

intended for peripheral grinding, side forces applied to

these wheels may cause them toshatter.

e ) Always use undamaged wheel flanges that are

of correct size and shape for your selected wheel.

Proper wheel flanges support the wheel thus reducing

the possibility of wheel breakage. Flanges for cut‑off

wheels may be different from grinding wheelflanges.

f ) Do not use worn down wheels from larger power

tools. A wheel intended for larger power tool is not

suitable for the higher speed of a smaller tool and

mayburst.

g ) When using dual purpose wheels always use

the correct guard for the application being

performed. Failure to use the correct guard may not

provide the desired level of guarding, which could lead

to seriousinjury.

d ) Use special care when working corners, sharp

edges, etc. Avoid bouncing and snagging the

accessory. Corners, sharp edges or bouncing have a

tendency to snag the rotating accessory and cause loss

of control orkickback.

e ) Do not attach a saw chain woodcarving blade,

segmented diamond wheel with a peripheral gap

greater than 10mm or toothed saw blade. Such

blades create frequent kickback and loss ofcontrol.

Évaluation

En savoir plus sur ce mode d’emploi

Nous comprenons qu’il est agréable d’avoir un mode d’emploi papier pour vos DeWalt DCG416VSB Meuleuse angulaire. Vous pouvez toujours télécharger le mode d’emploi depuis notre site Web et l’imprimer vous-même. Si vous souhaitez disposer d’un mode d’emploi original, nous vous recommandons de contacter DeWalt. Ils pourront peut-être fournir un mode d’emploi original. Recherchez-vous le mode d’emploi de votre DeWalt DCG416VSB Meuleuse angulaire dans une autre langue ? Choisissez votre langue préférée sur notre page d’accueil et recherchez le numéro de modèle pour voir si nous l’avons disponible.

Caractéristiques

Tous les modes d’emploi pour DeWalt Meuleuses angulaires
Plus de modes d’emploi de Meuleuses angulaires

Foire aux questions sur DeWalt DCG416VSB Meuleuse angulaire

Notre équipe d’assistance recherche des informations utiles sur les produits et des réponses aux questions fréquemment posées. Si vous trouvez une inexactitude dans notre foire aux questions, veuillez nous le faire savoir en utilisant notre formulaire de contact.

Produits connexes

Mode d’emploi

DeWalt D28131 Meuleuse angulaire

Mode d’emploi

DeWalt DWE43116N Meuleuse angulaire

Mode d’emploi

DeWalt DWE492 Meuleuse angulaire

Mode d’emploi

DeWalt DWE494 Meuleuse angulaire

Mode d’emploi

DeWalt DWE4233 Meuleuse angulaire

Mode d’emploi

DeWalt DCG415W1 Meuleuse angulaire

Mode d’emploi

DeWalt DCG413B Meuleuse angulaire

Mode d’emploi

DeWalt D28114 Meuleuse angulaire

Catégories associées