Mode d’emploi DeWalt DHS790AT2 Scie à onglet

Mode d’emploi

English

4

For your convenience and safety, the following warning labels are on your miter saw.

ON MOTOR HOUSING:

WARNING: TO REDUCE THE RISK OF INJURY, USER MUST READ

INSTRUCTION MANUAL BEFORE OPERATING MITER SAW.

WHEN SERVICING, USE ONLY IDENTICAL RE PLACE MENT PARTS.

DO NOT EXPOSE TO RAIN OR USE IN DAMP LOCATIONS.

ALWAYS USE PROPER EYE AND RESPIRATORY PROTECTION.

ON MOVING FENCES:

ALWAYS ADJUST FENCE PROPERLY BEFORE USE. CLAMP SMALL PIECES

BEFORE CUTTING. SEE MANUAL.

ON GUARD:

DANGER–KEEP AWAY FROM BLADE.

ON UPPER GUARD:

PROPERLY SECURE BRACKET WITH BOTH SCREWS BEFORE

USE.

ON TABLE: (2 PLACES)

WARNING: TO REDUCE THE RISK OF INJURY, USER MUST

READ INSTRUCTION MANUAL BEFORE OPERATING MITER

SAW. KEEP HANDS OUT OF PATH OF SAW BLADE. DO

NOT OPERATE SAW WITHOUT GUARDS IN PLACE. CHECK

LOWER GUARD FOR PROPER CLOSING BEFORE EACH USE.

ALWAYS TIGHTEN ADJUSTMENT KNOBS BEFORE USE. DO

NOT PERFORM ANY OPERATION FREEHAND. CLAMP SMALL PIECES BEFORE

CUTTING. NEVER REACH IN BACK OF SAW BLADE. NEVER CROSS ARMS

IN FRONT OF BLADE. TURN OFF TOOL AND WAIT FOR SAW BLADE TO

STOP BEFORE MOVING WORKPIECE, CHANGING SETTINGS OR MOVING

HANDS. REMOVE BATTERY PACK BEFORE ADJUSTING, CHANGING BLADE

OR SERVICING. TO REDUCE THE RISK OF INJURY, RETURN CARRIAGE TO

THE FULL REAR POSITION AFTER EACH CROSSCUT OPERATION. THINK! YOU

CAN PREVENT ACCIDENTS.

ON BASE: (2 PLACES)

Electrical Connection

Be sure your power source agrees with the nameplate marking. 120 volts, AC means that

your saw will operate on alternating current. Do not operate with DC power. A voltage

decrease of 10 percent or more will cause a loss of power and overheating. All D

e

WALT tools

are factory tested. If this tool does not operate, check the power supply.

This miter saw operates on either two 60V battery packs or by using the D

e

WALT corded

power supply.

Using the Corded Power Supply

The D

e

WALT corded power supply is designed to

Fig. 1

provide power for D

e

WALT 120V Max* FLEXVOLT

cordless tools. Insert the corded power supply into the

miter saw battery slot (refer to Installing and

Removing the Corded Power Supply) and plug the

power supply into an AC outlet. The power supply will

act as the power source to the tool. Your D

e

WALT

corded power supply should only be used with

standard household 120 VAC, 60 Hz power or a

120VAC 60Hz generator.

The corded power supply is suitable for use with both

grounded and double insulated 120V AC tools. When the power supply is utilized with a

grounded tool, the tool inlet will be equipped with a ground prong that allows the ground path

from the tool to connect to the power supply. When the power supply is used with this double

insulated miter saw, no ground connection is made from the tool to the power supply as no

ground connection is required.

Additional Specific Usage Instructions

The corded power supply may become warm to the touch during use. This is a normal

condition and does not indicate a problem.

IMPORTANT. The power supply is not user serviceable. There are no user serviceable parts

inside the power supply.

Servicing at an authorized service center is required to avoid damage to static sensitive

internal components.

Batteries and Chargers

The battery pack is not fully charged out of the carton. Before using the battery pack and

charger, read the safety instructions below and then follow charging procedures outlined.

When ordering replacement battery packs, be sure to include the catalog number andvoltage.

Your tool uses a D

e

WALT charger. Be sure to read all safety instructions before using

your charger. Consult the chart at the end of this manual for compatibility of chargers and

batterypacks.

Important Safety Instructions for All Battery Packs

WARNING: Read all safety warnings and all instructions for the battery pack, charger and

power tool. Failure to follow the warnings and instructions may result in electric shock, fire

and/or serious injury.

• Do not charge or use the battery pack in explosive atmospheres, such as

in the presence of flammable liquids, gases or dust. Inserting or removing the

battery pack from the charger may ignite the dust orfumes.

• Never force the battery pack into the charger. Do not modify the battery

pack in any way to fit into a non-compatible charger as battery pack may

rupture causing serious personal injury. Consult the chart at the end of this

manual for compatibility of batteries andchargers.

• Charge the battery packs only in designated D

e

WALTchargers.

• DO NOT splash or immerse in water or otherliquids.

• Do not store or use the tool and battery pack in locations where the

temperature may reach or exceed 104°F (40°C) (such as outside sheds or

metal buildings in summer). For best life store battery packs in a cool, drylocation.

NOTE: Do not store the battery packs in a tool with the trigger switch locked

on. Never tape the trigger switch in the ONposition.

Évaluation

En savoir plus sur ce mode d’emploi

Nous comprenons qu’il est agréable d’avoir un mode d’emploi papier pour vos DeWalt DHS790AT2 Scie à onglet. Vous pouvez toujours télécharger le mode d’emploi depuis notre site Web et l’imprimer vous-même. Si vous souhaitez disposer d’un mode d’emploi original, nous vous recommandons de contacter DeWalt. Ils pourront peut-être fournir un mode d’emploi original. Recherchez-vous le mode d’emploi de votre DeWalt DHS790AT2 Scie à onglet dans une autre langue ? Choisissez votre langue préférée sur notre page d’accueil et recherchez le numéro de modèle pour voir si nous l’avons disponible.

Caractéristiques

Tous les modes d’emploi pour DeWalt Scies à onglets
Plus de modes d’emploi de Scies à onglets

Foire aux questions sur DeWalt DHS790AT2 Scie à onglet

Notre équipe d’assistance recherche des informations utiles sur les produits et des réponses aux questions fréquemment posées. Si vous trouvez une inexactitude dans notre foire aux questions, veuillez nous le faire savoir en utilisant notre formulaire de contact.

Produits connexes

Mode d’emploi

DeWalt DWS715 Scie à onglet

Mode d’emploi

DeWalt DHS790AB Scie à onglet

Mode d’emploi

DeWalt DWS716 Scie à onglet

Mode d’emploi

DeWalt DWS716XPS Scie à onglet

Mode d’emploi

DeWalt DWS713 Scie à onglet

Mode d’emploi

DeWalt DWS780 Scie à onglet

Mode d’emploi

DeWalt DW705 Scie à onglet

Mode d’emploi

DeWalt DHS716AT2 Scie à onglet

Catégories associées