Mode d’emploi FERM TDM1011 Perceuse à colonne

Mode d’emploi

OPERATION, HINTS AND TIPS

DEPT STOP

Fig.F

The drill spindle is provided with a depth stop. It can be

adjusted using the nut. The drill depth can be read on the

scale division.

CLAMPING THE DRILL

Fig.G

In the drill head of the bench drill, drills and other tools

with a cylindrical shank can be clamped. The moment of

rotation is transferred to the drill by means of the ten-

sion of the three clamping jaws. To prevent the drill from

sliding away, it must be clamped using the toothed ring

wrench. If the drill slides away in the drill holder, a slight

burr occurs on the drill shank, which makes centric

clamping impossible. A burr which occurs in this way

must in any case be removed by grinding

CLAMPING THE WORKPIECE

Fig.H

The drill bench and the footplate of the bench drill are

provided with grooves for fastening clamping tools.

Always clamp the workpiece in the machine clamp or

other clamping tools. In this way you will prevent acci-

dents and even increase the drilling accuracy because the

workpiece is in a fixed position.

ADJUSTING THE BENCH

Fig.I

The drill bench is fastened to the drill column and can be

adjusted in height after loosening the fastening handle.

Adjust the bench in such a way that there is still enough

space between the top of the workpiece and the point of

the drill. You can also swivel the bench sideways, if you

wish to clamp a workpiece directly onto the footplate.

Fig.J

For slanted drilling and with a slanted supporting surface

of the workpiece the bench can be swivelled. For this

purpose loosen the hexagonal screw (20) on the hinge

point (21) of the bench and remove the centring. Swivel

the bench (19) to the desired position. Then screw

down the hexagonal screw (20) properly using a wrench.

NUMBER OF REVOLUTIONS,

SPEED OF ROTATION, SUPPLY

The supply, the feed motion of the drill, takes place by

hand on the 3-armed drill lever. The speed of rotation is

determined by the number of revolutions of the drill

spindle and by the diameter of the drill. The correct

choice of supply and the number of revolutions of the

drill spindle are the deciding factors for the lifespan of

the drill. The following applies as a basic rule: with a lar-

ger diameter of the drill the number of revolutions must

be adjusted lower; the greater the firmness of the work-

piece, the greater the cutting pressure must also be. In

order not to overheat the drill in this case, the supply and

speed of rotation must be lowered at the same time. In

addition, the drill must be cooled with drill oil. For thin

plates, quite large drillings must be carried out carefully

with little supply and little cutting pressure, so as to get a

precise result and so that the drilling remains the correct

size. For deep drilling (larger than 2 x the diameter of the

drill) the discharge of chips is more difficult and the tem-

perature of the drill is higher. Therefore lower the sup-

ply and the number of revolutions and ensure a better

discharge of chips by regularly pulling back the drill. For

drilling with a greater diameter than 8 mm, pre-drilling

must take place, so that early wear of the drill - main cut-

ting edge can be avoided and so that the drilling point is

not too heavily loaded.

MAINTENANCE

Make sure that the machine is not live when car-

rying out maintenance work on the motor.

The Ferm machines have been designed to operate over

a long period of time with a minimum of maintenance.

Continuous satisfactory operation depends upon pro-

per machine care and regular cleaning.

Cleaning

Keep the ventilation slots of the machine clean to pre-

vent overheating of the engine. Regularly clean the

machine housing with a soft cloth, preferably after each

use. Keep the ventilation slots free from dust and dirt. If

the dirt does not come off use a soft cloth moistened

with soapy water. Never use solvents such as petrol,

alcohol, ammonia water, etc. These solvents may

damage the plastic parts.

Lubrication

The machine do not need to be greased. All bearings and

driving gears are maintenance-free and greased for life.

The drill must be cleaned with compressed air or a dry

cloth. It is advisable to clean the blank parts from time to

time with environmentally friendly solvents and to only

grease withacid-free oil or grease.

Faults

Should a fault occur, e.g. after wear of a part, please con-

tact your local Ferm dealer.

In the back of this manual you find an exploded view

showing the parts that can be ordered.

ENVIRONMENT

In order to prevent the machine from damage during

transport, it is delivered in a sturdy packaging. Most of

the packaging materials can be recycled. Take these

materials to the appropriate recycling locations.

Take your unwanted machines to your local Ferm-

dealer. Here they will be disposed of in an environmen-

tally safe way.

Ferm 548 Ferm

Évaluation

En savoir plus sur ce mode d’emploi

Nous comprenons qu’il est agréable d’avoir un mode d’emploi papier pour vos FERM TDM1011 Perceuse à colonne. Vous pouvez toujours télécharger le mode d’emploi depuis notre site Web et l’imprimer vous-même. Si vous souhaitez disposer d’un mode d’emploi original, nous vous recommandons de contacter FERM. Ils pourront peut-être fournir un mode d’emploi original. Recherchez-vous le mode d’emploi de votre FERM TDM1011 Perceuse à colonne dans une autre langue ? Choisissez votre langue préférée sur notre page d’accueil et recherchez le numéro de modèle pour voir si nous l’avons disponible.

Caractéristiques

Tous les modes d’emploi pour FERM Perceuses à colonne
Plus de modes d’emploi de Perceuses à colonne

Foire aux questions sur FERM TDM1011 Perceuse à colonne

Notre équipe d’assistance recherche des informations utiles sur les produits et des réponses aux questions fréquemment posées. Si vous trouvez une inexactitude dans notre foire aux questions, veuillez nous le faire savoir en utilisant notre formulaire de contact.

Produits connexes

Mode d’emploi

FERM TDM1025 Perceuse à colonne

Mode d’emploi

FERM TDM1026 Perceuse à colonne

Mode d’emploi

FERM TDM1008 Perceuse à colonne

Mode d’emploi

FERM TDM1007 Perceuse à colonne

Mode d’emploi

FERM TDM1012 Perceuse à colonne

Mode d’emploi

FERM TDM1006 Perceuse à colonne

Mode d’emploi

FERM TDM1001 Perceuse à colonne

Mode d’emploi

FERM TDM1020 Perceuse à colonne

Catégories associées