Mode d’emploi FERM TSM1001 Banc de scie

Mode d’emploi

Ferm 35

AVAILABLE SPARE PARTS FOR FZT-250

EXPLODED VIEW 1

REF.NR. DESCRIPTION FERM NR.

1/2/3 SAWBLADE COVER COMPLETE 407460

13-18 ANGLE GAUGE COMPLETE 407461

19/20 TABLE INSERT 407462

22-35 SAWGUIDE COMPLETE 407463

45 GEAR SHAFT 407464

46 KEY 407465

47 GEAR 407466

54 ROTOR 407467

56 STATOR 407468

59/60/61 CARBON BRUSH + HOLDER 407469

81 HEX. NUT M16 x 1.5 407472

82 OUTSIDE FLANGE 407470

83 HARD METAL SAW BLADE 250 x 30 x16, T36 327252

83 HARD METAL SAW BLADE 250 x 30 x 16, T30 310360

84 INSIDE FLANGE 407471

103 CRANK 407473

111 MAGNETIC SWITCH 407474

115/116 FIXED BRACKET + RING 407475

Product: Ferm saw-bench

Type FZT-250, Art. nr. 420085

Ferm, Genemuiden, the Netherlands

Sound pressure level (L

pa

) 85 dB(A)

Acoustic capacity level (L

wa

) 99 dB(A)

Measurements of bench 685 x 430 mm

Suction mouth Ø 30 (22) mm

SERIAL NUMBER

The serial number on the machine is composed as fol-

lows:

Serial nr.

READ THESE INSTRUCTIONS FOR USE

PROPERLY BEFORE YOU USE THE SAW-

BENCH!

1. SPECIAL SAFETY

INSTRUCTIONS

1. When using the saw blades with hard metal teeth

(widia) it is advisable to use blades with a negative

or slightly positive cutting angle. Do not use any

saw blades with deeply cut teeth. They can grip the

protective cap.

2. Attention: First carefully assemble all the parts be-

fore starting work. Follow the procedure as indica-

ted.

3. If you are not familiar with using such a machine,

you would be better to be informed first by a pro-

fessional, an instructor or by a technician.

4. Always clamp or press the workpiece firmly

against the saw guide, before you carry out the

process. The use of all possible clamping set-ups is

preferable to using your hands.

5. Important: If you are holding the workpiece by

hand for the process to be carried out, keep a mini-

mum distance of 100 mm from the saw blade.

6. Always press the workpiece against the bench.

7. Keep the saw blade sharp and check regularly

whether it rotates freely without abnormal vibra-

tions. Replace the saw blade if necessary.

8. Allow the machine to rotate freely until it reaches

the maximum number of revolutions, before you

start the process.

9. Maintain the air inlets at the back and the bottom of

the bench saw machine and electric engine for a

longer machine life. Dust piles must be removed.

10. Always lock the different degree set-ups before

you start processing.

11. Only buy suitable saw blades with a number of re-

volutions of at least 6000 revolutions per minute.

12. Only use the correct saw blade. Too small or too

big saw blades are extremely dangerous.

13. Regularly inspect the saw blade for any faults. Re-

place the saw blade if necessary.

14. Grease the new saw blade and clean the flanges be-

fore you assemble the new blade. Then assemble

the blade in the correct direction and pull the flan-

ges firmly using the central bolt (left thread!)

15. Only use original flanges. All other types are not

suitable.

16. Never work without the protective cap of the saw

blade.

17. The moving part of the protective cap must also re-

main assembled.

18. Never grease the saw blade while it is rotating.

19. Always keep your hands removed from the track

of the saw blades.

20. Never pick up the workpiece by grasping with your

hands along or behind the saw blade.

21. Ensure that the workpiece never touches the saw

blade, before the machine has been switched on.

22. Never process metal or stone sorts with this ma-

chine.

23. Use support aids in order to support long work-

pieces.

24. Never use the machine in a dangerous environ-

ment, where inflammable gases or fluids are pre-

sent.

25. Never leave the machine unattended without first

disconnecting it from the mains voltage.

26. If you hear abnormal noises, try to trace them or

take the machine to a recognized fitter, or repair

company.

27. If a part is broken or damaged, replace it or repair it

immediately.

28. Never stand in the track of the saw blade but stand

to the left or the right of the saw bench.

29. Your hands must likewise be placed next to the

track of the saw blade.

30. Never use a wooden pole instead of your hands to

push the wood through the saw.

31. Always place the wood at the front of the saw ben-

ch and then push it further back.

ORDER NUMBER / CONSTRUCTION YEAR

GB

English

2 Ferm

VOLT WATT RPM mm mm mm kg

230V~50Hz 1.5 kW 4500 55 80 Ø 254 x 1,6 x 16 22

40 Teeth

45°

MM

1'

90°

MM

kg.

IP

20

Évaluation

En savoir plus sur ce mode d’emploi

Nous comprenons qu’il est agréable d’avoir un mode d’emploi papier pour vos FERM TSM1001 Banc de scie. Vous pouvez toujours télécharger le mode d’emploi depuis notre site Web et l’imprimer vous-même. Si vous souhaitez disposer d’un mode d’emploi original, nous vous recommandons de contacter FERM. Ils pourront peut-être fournir un mode d’emploi original. Recherchez-vous le mode d’emploi de votre FERM TSM1001 Banc de scie dans une autre langue ? Choisissez votre langue préférée sur notre page d’accueil et recherchez le numéro de modèle pour voir si nous l’avons disponible.

Caractéristiques

Tous les modes d’emploi pour FERM Bancs de scie
Plus de modes d’emploi de Bancs de scie