Mode d’emploi Güde Spalty W 370/4T Fendeuse à bois

Mode d’emploi

 Any other use will be considered a use in conflict with

the designation. The manufacturer will not be liable

for any consequential damage. The risk is borne by

the user.

Installation

Please make sure the appliance is installed evenly and

steadily on a solid surface with adequate lighting.

Make sure you have enough room to work safely and

undisturbed.

Residual risks

The appliance has been designed according to the state of

the art and recognised safety-technical regulations.

However, there still may be some residual risks when

working with the appliance.

 Risk of injury to fingers and hands by the splitter

when wood is guided or supported unprofessionally.

 Risk of injury by a thrown-away piece of wood as a

result of unprofessional holding or guiding.

 Risk of electric shock when unspecified feeder cables

are used.

 Further, there may be some hidden residual risks

despite all the preventive measures taken.

 Residual risks can be minimised if Safety

instructions and Use as designated and the entire

Operating Instructions are followed.

Plugging

Check regularly the feeder cables for any damage. Before

that, the appliance must be unplugged!

The feeder cable must be in accordance with applicable

provisions of VDE and DIN. Feeder cable with H 07-RN

marking to be used only. Sticking the type marking on the

feeder cable is mandatory.

Defective feeder cables

Insulation gets often damaged on the electric feeder

cables.

Possible causes:

Sores if feeder cables are guided in gaps under windows

or doors.

Breaks as a result of unprofessional fixing or guiding of

feeder cables.

Cutting-off as a result of the feeder cable being run over.

Insulation damage by pulling the cable out of wall socket.

Cracks as a result of insulation aging.

Feeder cables damaged in this way must not be used

– they are a risk to life due to the insulation damage!

Operation - pic. 3

Before starting your work, the air vent screw (pic. 2/12)

must be necessarily loosened by a few turns to enable air

circulation in the oil tank.

If it is kept tightened when working with the appliance, the

hydraulic movement would cause overpressure.

The screw must necessarily be tightened whenever the

appliance is to be transported to prevent oil leak.

Evenly cut pieces of wood to be split only.

1. Put the split wood flatways and evenly on the

supporting surface (pic. 1/3).

2. The log splitter has been fitted with two-handed

operation – left hand operates the hydraulic lever

(pic. 1/10) and right hand operates the starter (pic.

1/7).

3. Press the hydraulic lever (pic. 1/10) down as

specified and use the starter (pic. 1/7) to active the

splitting process.

If one operated part is released, the appliance stops

immediately. Releasing both operated parts makes the

pressure plate go back. If the appliance is unable to split

another piece of wood in 5 seconds, stop the process at

once. The wood to be split is probably too hard. Turn the

wood to be split by 90° and try once more.

Caution: For operation taking more than

5 seconds there is a risk of appliance overheating or

damage to be more specific. Interrupt the process.

Wrong fitting, pic. 3/A

The split wood to be put to the supporting surface flatways

at all times!

It must not slide down or be put askew. The splitting

wedge gets overloaded if splitting does not take place

along the entire edge but only in its upper part.

Never split more pieces at the same time!

There could be a risk that one of the pieces gets shot out

uncontrolled.

Caution! High risk of injury!

Stuck wood, pic. 3/B/C

Never try to knock the stuck wood out of the appliance.

This could lead to injuries and damage the appliance.

Proceed as follows:

1. Let the pressure plate get to the starting position.

2. Put a wedge under the wood to be split – see picture.

3. Perform one splitting cycle in a way the pressure

plate moves the wedge far under the wood you wish

to release.

4. Repeat the steps above with new wedges until the

wood is pushed up from the appliance.

Évaluation

En savoir plus sur ce mode d’emploi

Nous comprenons qu’il est agréable d’avoir un mode d’emploi papier pour vos Güde Spalty W 370/4T Fendeuse à bois. Vous pouvez toujours télécharger le mode d’emploi depuis notre site Web et l’imprimer vous-même. Si vous souhaitez disposer d’un mode d’emploi original, nous vous recommandons de contacter Gude. Ils pourront peut-être fournir un mode d’emploi original. Recherchez-vous le mode d’emploi de votre Güde Spalty W 370/4T Fendeuse à bois dans une autre langue ? Choisissez votre langue préférée sur notre page d’accueil et recherchez le numéro de modèle pour voir si nous l’avons disponible.

Caractéristiques

Tous les modes d’emploi pour Güde Fendeuses à bois
Plus de modes d’emploi de Fendeuses à bois

Foire aux questions sur Güde Spalty W 370/4T Fendeuse à bois

Notre équipe d’assistance recherche des informations utiles sur les produits et des réponses aux questions fréquemment posées. Si vous trouvez une inexactitude dans notre foire aux questions, veuillez nous le faire savoir en utilisant notre formulaire de contact.

Produits connexes

Mode d’emploi

Güde DHH 1050/8 TC-230 V Fendeuse à bois

Mode d’emploi

Güde Basic 8T/DTS Fendeuse à bois

Mode d’emploi

Güde DHH 1100/13 TZ Fendeuse à bois

Mode d’emploi

Güde Basic 10T/DTS Fendeuse à bois

Mode d’emploi

Güde Basic 14T/DTS Eco Fendeuse à bois

Mode d’emploi

Güde DHH 1050/7 T Eco Fendeuse à bois

Mode d’emploi

Güde W 520/5.5 T UG Fendeuse à bois

Mode d’emploi

Güde W520/7TW Fendeuse à bois

Catégories associées