Mode d’emploi Hikoki DS 14DSDL Perceuse visseuse

Mode d’emploi

3

English

c) When battery pack is not in use, keep it away

from other metal objects, like paper clips, coins,

keys, nails, screws or other small metal objects,

that can make a connection from one terminal to

another.

Shorting the battery terminals together may cause

burns or a fi re.

d) Under abusive conditions, liquid may be ejected

from the battery; avoid contact. If contact

accidentally occurs, fl ush with water. If liquid

contacts eyes, additionally seek medical help.

Liquid ejected from the battery may cause irritation or

burns.

6) Service

a) Have your power tool serviced by a qualifi ed

repair person using only identical replacement

parts.

This will ensure that the safety of the power tool is

maintained.

PRECAUTION

Keep children and infi rm persons away.

When not in use, tools should be stored out of reach of

children and infi rm persons.

CORDLESS DRIVER DRILL / IMPACT

DRIVER DRILL SAFETY WARNINGS

<DV14DSDL/DV18DSDL>

1. Wear ear protectors when impact drilling.

Exposure to noise can cause hearing loss.

<DS14DSDL/DS18DSDL/DV14DSDL/DV18DSDL>

1. Use auxiliary handle(s), if supplied with the tool.

Loss of control can cause personal injury.

2. Hold power tool by insulated gripping surfaces,

when performing an operation where the cutting

accessory or fastener may contact hidden wiring.

Cutting accessory and fasteners contacting a "live" wire

may make exposed metal parts of the power tool "live"

and could give the operator an electric shock.

ADDITIONAL SAFETY WARNINGS

1. Make sure that the area to be drilled is absolutely free

of any hidden obstructions including electrical wiring,

water, or gas pipes. Drilling into the aforementioned may

result in electric shock or short circuit, gas leak or other

hazards that can cause serious accidents or injuries.

2. Make sure to securely hold the tool during operation.

Failure to do so can result in accidents or injuries.

3. Secure the workpiece. A workpiece clamped with

clamping devices or in a vice is held more secure than

by hand.

4. Setting up and checking the work environment. Check

if the work environment is suitable by following the

precaution.

5. Do not allow foreign matter to enter the hole for

connecting the rechargeable battery.

6. Never disassemble the rechargeable battery and

charger.

7. Never short-circuit the rechargeable battery.

Shortcircuiting the battery will cause a great electric

current and overheat. It results in burn or damage to the

battery.

8. Do not dispose of the battery in fi re. If the battery is burnt,

it may explode.

9. Bring the battery to the shop from which it was purchased

as soon as the post-charging battery life becomes too

short for practical use. Do not dispose of the exhausted

battery.

10. Do not insert object into the air ventilation slots of the

charger. Inserting metal objects or infl ammables into the

charger air ventilation slots will result in electrical shock

hazard or damaged charger.

11. When mounting a bit into the keyless chuck, tighten the

sleeve adequately. If the sleeve is not tight, the bit may

slip or fall out, causing injury.

12. When changing the rotational speed with the shift knob,

confi rm that the switch is off . Changing the speed while

the motor is rotating will damage the gears.

13. The clutch dial cannot be set between the numerals "1,

3, 5 … 22" or the dots, and do not use with the clutch dial

numeral between "22" and the line at the middle of the

drill mark. Doing so may cause damage.

14. Resting the unit after continuous work.

15. After use for continuous tightening wood screw works,

rest the unit for 15 minutes or so when replacing the

battery. The temperature of the motor, switch, etc., will

rise if the work is started again immediately after battery

replacement, eventually resulting in burnout.

16. The motor may stop in the event the tool is overloaded. In

this should occur, release the tool’s switch and eliminate

the cause of the overload.

17. The motor rotation may be locked to cease while the unit

is used as drill. While operating the driver drill, take care

not to lock the motor.

18. If motor is locked, immediately turn the power off . If the

motor is locked for a while, the motor or battery may be

burnt.

19. The use of the battery in a cold condition (below 0 degree

Centigrade) can sometimes result in the weakened

tightening torque and reduced amount of work. This,

however, is a temporary phenomenon, and returns to

normal when the battery warms up.

20. Install securely the hook. Unless the hook is securely

installed, it may cause an injury while using.

21. To prevent the battery power consumption caused

by forgetting to turn off the LED light, the light goes off

automatically in about 15 minutes.

22. Do not look directly into the light. Such actions could

result in eye injury.

CAUTION ON LITHIUM-ION BATTERY

To extend the lifetime, the lithium-ion battery equips with the

protection function to stop the output.

In the cases of 1 to 3 described below, when using this

product, even if you are pulling the switch, the motor may

stop. This is not the trouble but the result of protection

function.

1. When the battery power remaining runs out, the motor

stops.

In such a case, charge it up immediately.

2. If the tool is overloaded, the motor may stop. In this

case, release the switch of tool and eliminate causes of

overloading. After that, you can use it again.

3. If the battery is overheated under overload work, the

battery power may stop.

In this case, stop using the battery and let the battery

cool. After that, you can use it again.

Furthermore, please heed the following warning and caution.

WARNING

In order to prevent any battery leakage, heat generation,

smoke emission, explosion and ignition beforehand, please

be sure to heed the following precautions.

1. Make sure that swarf and dust do not collect on the

battery.

○ During work make sure that swarf and dust do not fall on

the battery.

○ Make sure that any swarf and dust falling on the power

tool during work do not collect on the battery.

0000BookDS14DSDL.indb30000BookDS14DSDL.indb3 2017/12/0410:34:222017/12/0410:34:22

Évaluation

En savoir plus sur ce mode d’emploi

Nous comprenons qu’il est agréable d’avoir un mode d’emploi papier pour vos Hikoki DS 14DSDL Perceuse visseuse. Vous pouvez toujours télécharger le mode d’emploi depuis notre site Web et l’imprimer vous-même. Si vous souhaitez disposer d’un mode d’emploi original, nous vous recommandons de contacter Hikoki. Ils pourront peut-être fournir un mode d’emploi original. Recherchez-vous le mode d’emploi de votre Hikoki DS 14DSDL Perceuse visseuse dans une autre langue ? Choisissez votre langue préférée sur notre page d’accueil et recherchez le numéro de modèle pour voir si nous l’avons disponible.

Caractéristiques

Tous les modes d’emploi pour Hikoki Perceuses visseuses
Plus de modes d’emploi de Perceuses visseuses

Foire aux questions sur Hikoki DS 14DSDL Perceuse visseuse

Notre équipe d’assistance recherche des informations utiles sur les produits et des réponses aux questions fréquemment posées. Si vous trouvez une inexactitude dans notre foire aux questions, veuillez nous le faire savoir en utilisant notre formulaire de contact.

Produits connexes

Mode d’emploi

Hikoki DS 14DL2 Perceuse visseuse

Mode d’emploi

Hikoki DS 9DVF3 Perceuse visseuse

Mode d’emploi

Hikoki DS 14DCL Perceuse visseuse

Mode d’emploi

Hikoki DS 10DAL Perceuse visseuse

Mode d’emploi

Hikoki DS 18DD Perceuse visseuse

Mode d’emploi

Hikoki DV 18DGAL Perceuse visseuse

Mode d’emploi

Hikoki DV 18DD Perceuse visseuse

Mode d’emploi

DeWalt DCD799B Perceuse visseuse

Catégories associées