Mode d’emploi Hitachi B 16RM Perceuse à colonne

Mode d’emploi

— 6 —

English

GROUNDING INSTRUCTIONS

IN THE EVENT OF A MALFUNCTION OR BREAKDOWN,

grounding provides a path of least resistance for electric

current and reduces the risk of shock. This tool is

equipped with an electric cord that has an equipment

grounding conductor and grounding plug. The plug MUST

be plugged into a matching receptacle that is properly

installed and grounded in accordance with ALL local

codes and ordinances.

DO NOT MODIFY THE PLUG PROVIDED. If it will not fit the

receptacle, have the proper receptacle installed by a

qualified electrician.

IMPROPER CONNECTION of the equipment grounding

conductor can result in risk of electric shock. The

conductor with the green insulation (with or without

yellow stripes) is the equipment grounding conductor. If

repair or replacement of the electric cord or plug is

necessary, DO NOT connect the equipment grounding

conductor to a live terminal.

CHECK with a qualified electrician or service personnel if

you do not completely understand the grounding

instructions, or if you are not sure the tool is properly

grounded.

USE ONLY 3-WIRE EXTENSION CORDS THAT HAVE 3-

PRONG GROUNDING PLUGS AND 3-POLE RECEPTACLE

THAT ACCEPT THE TOOL’S PLUG. REPAIR OR REPLACE

DAMAGED OR WORN CORD IMMEDIATELY.

GUIDELINES FOR EXTENSION CORDS

Make sure your extension cord is in good condition. When

using an extension cord, be sure to use one heavy enough

to carry the current your product will draw. An undersized

cord will cause a drop in line voltage resulting in loss of

power and overheating. The table below shows the

correct size to use according to cord length and nameplate

ampere rating. If in doubt, use the next heavier gauge.

The smaller the gauge number, the heavier the cord.

Be sure your extension cord is properly wired and in good

condition. Always replace a damaged extension cord or

have it repaired by a qualified person before using it.

Protect your extension cords from sharp objects,

excessive heat and damp or wet areas.

Use a separate electrical circuit for your tools. This circuit

must not be less than #12 wire and should be protected

with a 15 Amp time lag fuse. Before connecting the motor

to the power line, make sure the switch is in the OFF

position and the electric current is rated the same as the

current stamped on the motor nameplate. Running at a

lower voltage will damage the motor.

This tool is intended for use on a circuit that has a

receptacle like the one illustrated in FIGURE A.

FIGURE A shows a 3-prong electrical plug and receptacle

that has a grounding conductor. If a properly grounded

receptacle is not available, an adapter (FIGURE B) can be

used to temporarily connect this plug to a 2-contact

ungrounded receptacle. The adapter (FIGURE B) has a

rigid lug extending from it that MUST be connected to a

permanent earth ground, such as a properly grounded

receptacle box. THE TEMPORARY ADAPTER SHOULD BE

USED ONLY UNTIL A PROPER GROUNDED OUTLET CAN

BE INSTALLED BY A QUALIFIED ELECTRICIAN. The

Canadian Electrical Code prohibits the use of adapters.

CAUTION: In all cases, make certain the receptacle in

question is properly grounded. If you are not sure have a

certified electrician check the receptacle.

WARNING

This drill press is for indoor use only. Do not expose to

rain or use in damp locations.

Fig. A

3-Prong Plug

Propely Grounded

3-Prong Receptacle

Grounding Prong

Fig. B

Grounding Lug

Adapter

2-Prong

Receptacle

Make Sure This is

Connected to a

Known Ground

WARNING

This tool must be grounded while in use to protect the

operator from electrical.

MINMUN GAUGE FOR EXTENSION CORDS (AWG)

(When using 120 volts only)

Ampere Rating Total length of cord in feet

not

more than more than 25' 50' 100' 150'

0 6 18 16 16 14

6 10 18161412

10 12 16 16 14 12

Not

12 16 14 12 recommended

SAVE THESE INSTRUCTIONSSAVE THESE INSTRUCTIONS

Évaluation

En savoir plus sur ce mode d’emploi

Nous comprenons qu’il est agréable d’avoir un mode d’emploi papier pour vos Hitachi B 16RM Perceuse à colonne. Vous pouvez toujours télécharger le mode d’emploi depuis notre site Web et l’imprimer vous-même. Si vous souhaitez disposer d’un mode d’emploi original, nous vous recommandons de contacter Hitachi. Ils pourront peut-être fournir un mode d’emploi original. Recherchez-vous le mode d’emploi de votre Hitachi B 16RM Perceuse à colonne dans une autre langue ? Choisissez votre langue préférée sur notre page d’accueil et recherchez le numéro de modèle pour voir si nous l’avons disponible.

Caractéristiques

Tous les modes d’emploi pour Hitachi Perceuses à colonne
Plus de modes d’emploi de Perceuses à colonne

Foire aux questions sur Hitachi B 16RM Perceuse à colonne

Notre équipe d’assistance recherche des informations utiles sur les produits et des réponses aux questions fréquemment posées. Si vous trouvez une inexactitude dans notre foire aux questions, veuillez nous le faire savoir en utilisant notre formulaire de contact.

Produits connexes

Mode d’emploi

FERM TDM1003 Perceuse à colonne

Mode d’emploi

FEMI DIGI MAX-13 Perceuse à colonne

Mode d’emploi

Ryobi DP103L Perceuse à colonne

Mode d’emploi

FERM TDM1008 Perceuse à colonne

Mode d’emploi

Scheppach DP60 Perceuse à colonne

Mode d’emploi

Scheppach rab t16x Perceuse à colonne

Mode d’emploi

Scheppach stb s16 Perceuse à colonne

Mode d’emploi

Far Tools DPB 16E Perceuse à colonne

Catégories associées