Mode d’emploi Honeywell HSF1640B Ventilateur

Mode d’emploi

2 3

PART GUIDE

BASE ASSEMBLY

BLADE AND GRILLES ASSEMBLY

1. Align the pole in the base using tabs as a guide.

2. Gently place base on its side. (Fig. 3)

3. Insert and tighten the L shaped bolt and washer

on the bottom of the fan base. (Fig. 4)

4. Tighten by turning clockwise.

The small blade is packaged separately in between cardboard apart from the

large blade DO NOT THROW OUT!

1. Unscrew the blade nut clockwise and the plastic nut counterclockwise

and set aside. (Fig. 5)

2. Position the rear grille onto the fan head assembly making sure the two

alignment holes are aligned with the two prongs.

3. Screw on plastic nut tightly clockwise to attach rear grille. (Fig. 6)

4. Install the blade onto the shaft until the retaining

pin fits into the notch on the blade. Now place

the small blade on to the shaft making sure the

alignment pin is inserted into one of the three

holes on the large blade.

5. Screw blade nut to the motor shaft

counterclockwise (tighten by turning to the left).

(Fig. 7)

6. Mount the front grille and secure using the locking clips.

1 Front Grille

2 Locking Clips

3 Blade Nut

4 Small Blade

5 Large Blade

6 Plastic Nut

7 Rear Grille

8 Fan Head Assembly

9 Control Panel

10 Washer

11 “L” Screw

12 Motor Shaft

13 Alignment Prongs

14 Locking Screw

15 Extension Pole

16 Pole Locking Nut

17 Lower Pole

18 Base

19 Remote Control

12 13

8

14

18

17

16

15

10

11

19

76

9

5

4

3

1

2

14. Place the fan on a dry level surface.

15. DO NOT hang or mount fan on a wall

or ceiling.

16. DO NOT operate if the fan housing

is damaged.

17. A loose fit between the AC outlet (receptacle)

and plug may cause overheating and a

distortion of the plug. Contact a qualified

electrician to replace loose or worn outlet.

18.

DO NOT

operate any fan with a damaged

cord or plug. Discard any damaged fan,

return the fan to the retailer where the

fan was purchased, or request a return

authorization to return to Kaz, Inc. for

examination and/or repair.

19.

DO NOT

run fan cord under carpeting.

DO

NOT

cover cord with throw rugs, runners, or

similar coverings.

DO NOT

route cord under

furniture or appliances. Arrange cord away

from traffic areas and where it will not be

tripped over.

WARNING: To Reduce The Risk of Fire or

Electric Shock, Do Not Use This Fan With Any

Solid State Speed Conrol Device.

FUSED SAFETY PLUG - FOR US MODELS ONLY

USER SERVICING INSTRUCTIONS

• If your fan loses power and you suspect that the fuse on your fan has blown,

grasp plug and remove from the receptacle or other outlet device. Do not

unplug by pulling on cord.

• Slide fuse cover, located on the top of the plug towards the prongs of the plug.

(Fig. 1)

• Carefully remove the blown fuse and snap a new fuse into place. To Reduce

the Risk of Fire, replace fuse only with 2.5 Amp, 125 volt fuse. Fully close the

fuse door by sliding back into place. (Fig. 2) Discard the blown fuse. The plug

should now be ready for normal use.

• To Reduce the Risk of Fire, do not replace attachment plug. Contains a

safety device (fuse) that should not be removed. Discard product if the

attachment plug is damaged.

• If you need further information on how or when to replace the fuse in the

safety plug, please contact Kaz Consumer Relations Department by visiting

our website at www.honeywellpluggedin.com/fans

or calling 18004770457.

This fan features a fused safety plug which is designed to cut off electric current to the fan if an electrical fault

occurs. Please see below for more information on how to properly use your fan and replace the safety plug fuse,

if needed.

Fig. 1

Fig. 2

Fig. 3 Fig. 4

Fig. 5

Fig. 6 Fig. 7

Évaluation

En savoir plus sur ce mode d’emploi

Nous comprenons qu’il est agréable d’avoir un mode d’emploi papier pour vos Honeywell HSF1640B Ventilateur. Vous pouvez toujours télécharger le mode d’emploi depuis notre site Web et l’imprimer vous-même. Si vous souhaitez disposer d’un mode d’emploi original, nous vous recommandons de contacter Honeywell. Ils pourront peut-être fournir un mode d’emploi original. Recherchez-vous le mode d’emploi de votre Honeywell HSF1640B Ventilateur dans une autre langue ? Choisissez votre langue préférée sur notre page d’accueil et recherchez le numéro de modèle pour voir si nous l’avons disponible.

Caractéristiques

Tous les modes d’emploi pour Honeywell Ventilateurs
Plus de modes d’emploi de Ventilateurs

Foire aux questions sur Honeywell HSF1640B Ventilateur

Notre équipe d’assistance recherche des informations utiles sur les produits et des réponses aux questions fréquemment posées. Si vous trouvez une inexactitude dans notre foire aux questions, veuillez nous le faire savoir en utilisant notre formulaire de contact.

Produits connexes

Mode d’emploi

Honeywell EFY-041 Ventilateur

Mode d’emploi

Honeywell HSF1640W Ventilateur

Mode d’emploi

Honeywell HT-906 Turbo Force Ventilateur

Mode d’emploi

Honeywell HT-216E Ventilateur

Mode d’emploi

Honeywell HY-041W Ventilateur

Mode d’emploi

Honeywell HY-280-TGT QuietSet Ventilateur

Mode d’emploi

Honeywell HYF290B Ventilateur

Mode d’emploi

Honeywell HFS-641PC Ventilateur

Catégories associées