Mode d’emploi JVC WR-DVP3U Étui pour appareil photo sous-marin
Besoin d'un mode d’emploi pour votre JVC WR-DVP3U Étui pour appareil photo sous-marin ? Ci-dessous, vous pouvez consulter et télécharger gratuitement le mode d’emploi PDF en français. Ce produit a actuellement 0 questions fréquemment posées, 0 commentaires et 0 votes. Si ce n'est pas le mode d’emploi que vous souhaitez, veuillez nous contacter.
Votre produit est défectueux et le mode d’emploi n’offre aucune solution ? Rendez-vous à un Repair Café pour obtenir des services de réparation gratuits.
Mode d’emploi
Loading…
Mounting method and operating method
for each part
1 Tighten the camcorder’s grip strap.
2 Remove the four buckles on the marine
case and open the front lid.
3 Align the Power Lever with the “OFF”
mark on the marine case.
4 Set the camcorder’s Power Switch to
“OFF”, then open the LCD monitor and
insert the camera into the marine case.
Place the included anti-fogging silica gel in the gap between the
camcorder and the marine case to prevent fogging in the marine
case.
• Only the BN-V107 battery can be used.
• Remove the grip belt or strap from the camcorder before inserting
it.
• If the camcorder’s Power Switch is set to “
”, perform settings as
required then insert the camcorder into the marine case.
5 Fit the Zoom Lever projection on the
marine case over the outer groove of
the Power Zoom Ring on the
camcorder, making sure that it is
securely fit.
If the camcorder’s Power Switch
is not set properly when the
camcorder is placed in the marine
case, it could break and/or it could
damage the Power Lever aligning
boss on the marine case.
6 Before sealing the marine case, check that there is no sand, dirt, or
other foreign matter on the O-ring mounted on the front lid or on
the O-ring contact surface on the main
unit.
Also make sure that the inserted silica gel
bag is not pinched. If you dive with foreign
matter trapped in these areas, water will
leak.
7 Check that the O-ring on the front lid is
correctly mounted in the groove, then press
in the front lid. Flip down the four buckles
in the directions indicated by the arrows in
the figure on the right to seal the marine
case.
8 Turn the marine case’s Power Lever in the
direction of the arrow to set the
camcorder’s Power Switch to “
” or “ ”.
• The camcorder’s Power Lamp lights.
9 To start video recording, press the Record-
ing Start/Stop Button.
To stop video recording, press it again.
• Press the Snapshot Button to perform
Snapshot recording.
0 The zoom can be adjusted with the Zoom
Lever.
• Telephoto : turn the lever to the left (
)
• Wide angle : turn the lever to the right
(
)
! When you are finished shooting, set the
marine case’s Power Lever to “OFF” (in the
direction of the arrow) to set the
camcorder’s Power Switch to “OFF”.
• The camcorder’s Power Lamp goes out.
NOTES:
䡲 The O-ring is made from rubber and is mounted on
the front lid.
䡲 Refer to the camcorder’s instructions for more
information.
POWER
ON
OFF
WR-DVP3U
ZOOM
SNAP SHOT
START/STOP
POWER
ON
OFF
1
2
3
3
56
9
78
4
User’s Manual ENGLISH
Names of the parts
Please read before use.
This marine case is a precision instrument designed to permit safe
video recording under high water pressure. Please pay careful
attention when handling the unit before and after use, as explained
in this user’s manual.
Each part of the marine case has been subject to strict controls
during the manufacturing process, and the individual functions
have faced stringent tests during the assembly process. Each marine
case has also had to pass water-proof inspections using high-
pressure water testers. However, damage can sometimes occur
during transport and distribution, or during storage after purchase,
so before diving always carry out the following pre-use test to
verify safety.
Pre-use test
Be sure to perform the following pre-use test before diving.
1. Before mounting the camcorder inside the marine case, dive
with only the empty marine case and test for water leaks.
• Check for leaks at a depth of 3 m where there is no water
pressure. Allow 5 or 6 minutes to ensure there are no leaks. Be
sure to perform this test to ensure the safety of your camcorder.
2. The following are some common causes of water leaks:
A. The marine case is used without attaching the O-ring.
B. The O-ring is not mounted in the correct position.
C. The O-ring is damaged or deformed.
D. There is sand, dirt, hair or other foreign matter on the O-ring.
E. There is sand, dirt, hair or other foreign matter on the contact
surface of the O-ring or on the inside of the lid.
F. The provided strap or silica gel bag is pinched inside the
marine case when the lid is closed.
To protect your camcorder and ensure optimum use, keep the
examples listed above in mind when using the marine case.
JVC accepts no responsibility for water leakage or damage to
anything inside the marine case (camcorder, cassette, etc.) due to
careless usage of this product. Be sure to follow correct procedures
when using the marine case.
For Digital Video Camera
GR-DVP1, GR-DVP3
Before use, this unit must be pre-tested
to check if there is any water leakage.
WR-DVP3U
Marine Case
LYT0839-001A
Front glass
Strap
Fit the Zoom Lever projection
over the Power Zoom Ring
Projection
Power Zoom
Ring
1 Marine case front lid
2 Main unit
3 Buckle
4 Grip attachment holes
5 Power lever (POWER)
6 Recording start/stop button (START/STOP)
7 Zoom lever (ZOOM)
8 Snapshot button (SNAP SHOT)
9 Grip strap
O-ring
Bottom view
Grip strap
ZOOM
START/STOP
POWER
ON
OFF
ZOOM
START/STOP
POWER
ON
OFF
Snapshot
button
ZOOM
START/STOP
POWER
ON
OFF
Recording
start/stop
button
Loading…
Évaluation
Dites-nous ce que vous pensez du JVC WR-DVP3U Étui pour appareil photo sous-marin en laissant une note de produit. Vous voulez partager vos expériences avec ce produit ou poser une question ? Veuillez laisser un commentaire au bas de la page.En savoir plus sur ce mode d’emploi
Nous comprenons qu’il est agréable d’avoir un mode d’emploi papier pour vos JVC WR-DVP3U Étui pour appareil photo sous-marin. Vous pouvez toujours télécharger le mode d’emploi depuis notre site Web et l’imprimer vous-même. Si vous souhaitez disposer d’un mode d’emploi original, nous vous recommandons de contacter JVC. Ils pourront peut-être fournir un mode d’emploi original. Recherchez-vous le mode d’emploi de votre JVC WR-DVP3U Étui pour appareil photo sous-marin dans une autre langue ? Choisissez votre langue préférée sur notre page d’accueil et recherchez le numéro de modèle pour voir si nous l’avons disponible.
Caractéristiques
| Marque | JVC |
| Modèle | WR-DVP3U |
| Catégorie | Étuis pour appareils photo sous-marins |
| Type de fichier | |
| Taille du fichier | 0.84 MB |
Tous les modes d’emploi pour JVC Étuis pour appareils photo sous-marins
Plus de modes d’emploi de Étuis pour appareils photo sous-marins
Joignez-vous à la conversation sur ce produit
Ici, vous pouvez partager ce que vous pensez du JVC WR-DVP3U Étui pour appareil photo sous-marin. Si vous avez une question, lisez d’abord attentivement le mode d’emploi. La demande d’un mode d’emploi peut être effectuée en utilisant notre formulaire de contact.