Mode d’emploi Makita 5094D Scie circulaire

Mode d’emploi

3

13. Do not force tool. Use the correct tool for your

application. The correct tool will do the job better

and safer at the rate for which it is designed.

14. Do not use tool if switch does not turn it on or

off. A tool that cannot be controlled with the switch is

dangerous and must be repaired.

15. Disconnect battery pack from tool or place the

switch in the locked or off position before mak-

ing any adjustments, changing accessories, or

storing the tool. Such preventive safety measures

reduce the risk of starting the tool accidentally.

16. Store idle tools out of reach of children and

other untrained persons. Tools are dangerous in

the hands of untrained users.

17. When battery pack is not in use, keep it away

from other metal objects like: paper clips, coins,

keys, nails, screws, or other small metal objects

that can make a connection from one terminal to

another. Shorting the battery terminals together

may cause sparks, burns, or a fire.

18. Maintain tools with care. Keep cutting tools

sharp and clean. Properly maintained tools with

sharp cutting edge are less likely to bind and are

easier to control.

19. Check for misalignment or binding of moving

parts, breakage of parts, and any other condition

that may affect the tool’s operation. If damaged,

have the tool serviced before using. Many acci-

dents are caused by poorly maintained tools.

20. Use only accessories that are recommended by

the manufacturer for your model. Accessories

that may be suitable for one tool may create a risk of

injury when used on another tool.

SERVICE

21. Tool service must be performed only by qualified

repair personnel. Service or maintenance per-

formed by unqualified personnel may result in a risk

of injury.

22. When servicing a tool, use only identical

replacement parts. Follow instructions in the

Maintenance section of this manual. Use of unau-

thorized parts or failure to follow Maintenance

instructions may create a risk of shock or injury.

SPECIFIC SAFETY RULES

USB068-2

DO NOT let comfort or familiarity with

product (gained from repeated use)

replace strict adherence to circular saw

safety rules. If you use this tool unsafely

or incorrectly, you can suffer serious per-

sonal injury.

1. DANGER! Keep hands away from cutting area

and blade. Keep your second hand on auxiliary

handle or motor housing. If both hands are holding

the saw, they cannot be cut by the blade.

Keep your body positioned to either side of the

saw blade, but not in line with the saw blade.

KICKBACK could cause the saw to jump backwards.

(See “Causes and Operator Prevention of Kick-

back”)

Do not reach underneath the work. The guard can

not protect you from the blade below the work. Do

not attempt to remove cut material when blade is

moving.

CAUTION: Blades coast after turn off. Wait until

blade stops before grasping cut material.

2. Check lower guard for proper closing before

each use. Do not operate saw if lower guard

does not move freely and close instantly. Never

clamp or tie the lower guard into the open posi-

tion. If saw is accidentally dropped, lower guard may

be bent. Raise the lower guard with the Retracting

Lever and make sure it moves freely and does not

touch the blade or any other part, in all angles and

depths of cut.

To check lower guard, open lower guard by hand,

then release and watch guard closure. Also check to

see that Retracting Lever does not touch tool hous-

ing. Leaving blade exposed is VERY DANGEROUS

and can lead to serious personal injury.

3. Check the operation and condition of the lower

guard spring. If the guard and the spring are not

operating properly, they must be serviced before

use. Lower guard may operate sluggishly due to

damaged parts, gummy deposits, or a buildup of

debris.

4. Lower guard should be retracted manually only

for special cuts such as “Pocket Cuts” and

“Compound Cuts.” Raise lower guard by Retract-

ing Lever. As soon as blade enters the material,

lower guard must be released. For all other saw-

ing, the lower guard should operate automatically.

5. Always observe that the lower guard is covering

the blade before placing saw down on bench or

floor. An unprotected, coasting blade will cause the

saw to walk backwards, cutting whatever is in its

path. Be aware of the time it takes for the blade to

stop after switch is released.

6. NEVER hold piece being cut in your hands or

across your leg. It is important to support the work

properly to minimize body exposure, blade binding,

or loss of control.

7. Hold tool by insulated gripping surfaces when

performing an operation where the cutting tool

may contact hidden wiring. Contact with a “live”

wire will also make exposed metal parts of the tool

“live” and shock the operator.

8. When ripping always use a rip fence or straight

edge guide. This improves the accuracy of cut and

reduces the chance for blade binding.

9. Always use blades with correct size and shape

(diamond vs. round) arbor holes. Blades that do

Évaluation

En savoir plus sur ce mode d’emploi

Nous comprenons qu’il est agréable d’avoir un mode d’emploi papier pour vos Makita 5094D Scie circulaire. Vous pouvez toujours télécharger le mode d’emploi depuis notre site Web et l’imprimer vous-même. Si vous souhaitez disposer d’un mode d’emploi original, nous vous recommandons de contacter Makita. Ils pourront peut-être fournir un mode d’emploi original. Recherchez-vous le mode d’emploi de votre Makita 5094D Scie circulaire dans une autre langue ? Choisissez votre langue préférée sur notre page d’accueil et recherchez le numéro de modèle pour voir si nous l’avons disponible.

Caractéristiques

Tous les modes d’emploi pour Makita Scies circulaires
Plus de modes d’emploi de Scies circulaires

Foire aux questions sur Makita 5094D Scie circulaire

Notre équipe d’assistance recherche des informations utiles sur les produits et des réponses aux questions fréquemment posées. Si vous trouvez une inexactitude dans notre foire aux questions, veuillez nous le faire savoir en utilisant notre formulaire de contact.

Produits connexes

Mode d’emploi

Makita HS0600 Scie circulaire

Mode d’emploi

Makita CC301D Scie circulaire

Mode d’emploi

Makita LS1214 Scie circulaire

Mode d’emploi

Makita DHS630ZJ Scie circulaire

Mode d’emploi

Makita DHS661 Scie circulaire

Mode d’emploi

Makita LS0714L Scie circulaire

Mode d’emploi

Makita BSR730 Scie circulaire

Mode d’emploi

Makita CC300D Scie circulaire

Catégories associées