Mode d’emploi Makita 6824 Visseuse

Mode d’emploi

5

Reversing switch action (Fig. 5)

CAUTION:

• Always check the direction of rotation before operation.

• Use the reversing switch only after the tool comes to a

complete stop. Charging the direction of rotation before

the tool stops may damage the tool.

This tool has a reversing switch to change the direction of

rotation. Move the reversing switch lever to

the

D position (A side) for clockwise rotation or the

E position (B side) for counterclockwise rotation.

Hook (Fig. 6 &7)

The hook is convenient for temporarily hanging the tool.

When using the hook, pull it out in “A” direction and then

push it in “B” direction to secure in place.

When not using the hook, return it back to its initial posi-

tion by following the above procedures in reverse.

ASSEMBLY

CAUTION:

• Always be sure that the tool is switched off and

unplugged before carrying out any work on the tool.

Installing or removing bit (Fig. 8 & 9)

To remove the bit, first pull the locator out of the locking

sleeve. Then grasp the bit with a pair of pliers and pull the

bit out of the magnetic bit holder. Sometimes, it helps to

wiggle the bit with the pliers as you pull.

To install the bit, push it firmly into the magnetic bit

holder. Then install the locator by pushing it firmly back

onto the locking sleeve.

Installing removable cord adapter

For Model 6825R

Insert the Removable Cord Adapter as far as it goes so

that the marking on an end of the Removable Cord

Adapter on the side of connecting to power supply cord is

aligned to the marking on the other end of the

Removable Cord Adapter on the side of connecting to the

tool. (Fig. 10)

Turn the Removable Cord Adapter clockwise until it is

locked with a lock button. (Fig. 11)

And at this time the marking on an end of the

Removable Cord Adapter on the side of power supply

cord is aligned to the marking on the other end of the

Removable Cord Adapter on the side of connecting to the

tool. (Fig. 12)

Removing removable cord adapter

Rotate the Removable Cord Adapter counterclockwise

until it stops while pressing the lower part of the lock but-

ton. (Fig. 13)

Then pull the Removable Cord Adapter in that position.

(Fig. 14)

OPERATION

Fit the screw on the point of the bit and place the point of

the screw on the surface of the workpiece to be fastened.

Apply pressure to the tool and start it. Withdraw the tool

as soon as the clutch cuts in. Then release the switch

trigger. (Fig. 15)

CAUTION:

• When fitting the screw onto the point of the bit, be care-

ful not to push in on the screw. If the screw is pushed

in, the clutch will engage and the screw will rotate sud-

denly. This could damage a workpiece or cause an

injury.

• Make sure that the bit is inserted straight in the screw

head, or the screw and/or bit may be damaged.

MAINTENANCE

CAUTION:

• Always be sure that the tool is switched off and

unplugged before attempting to perform inspection or

maintenance.

To maintain product SAFETY and RELIABILITY, repairs,

carbon brush inspection and replacement, any other

maintenance or adjustment should be performed by Mak-

ita Authorized Service Centers, always using Makita

replacement parts.

ACCESSORIES

CAUTION:

• These accessories or attachments are recommended

for use with your Makita tool specified in this manual.

The use of any other accessories or attachments might

present a risk of injury to persons. Only use accessory

or attachment for its stated purpose.

If you need any assistance for more details regarding

these accessories, ask your local Makita Service Center.

• Phillips insert bits

• Magnetic bit holder

• Locator

• Plastic carrying case

ENG102-2

For European countries only

Noise

The typical A-weighted noise level determined according

to EN60745:

Sound pressure level (

L

pA

): 82 dB (A)

Sound power level (

L

WA

): 93 dB (A)

Uncertainty (K): 3 dB (A)

Wear ear protection.

ENG204-2

Vibration

The vibration total value (tri-axial vector sum) determined

according to EN60745:

Work mode: screwdriving without impact

Vibration emission (

a

h

): 2.5 m/s

2

or less

Uncertainty (K): 1.5 m/s

2

ENG901-1

• The declared vibration emission value has been mea-

sured in accordance with the standard test method and

may be used for comparing one tool with another.

• The declared vibration emission value may also be

used in a preliminary assessment of exposure.

Évaluation

En savoir plus sur ce mode d’emploi

Nous comprenons qu’il est agréable d’avoir un mode d’emploi papier pour vos Makita 6824 Visseuse. Vous pouvez toujours télécharger le mode d’emploi depuis notre site Web et l’imprimer vous-même. Si vous souhaitez disposer d’un mode d’emploi original, nous vous recommandons de contacter Makita. Ils pourront peut-être fournir un mode d’emploi original. Recherchez-vous le mode d’emploi de votre Makita 6824 Visseuse dans une autre langue ? Choisissez votre langue préférée sur notre page d’accueil et recherchez le numéro de modèle pour voir si nous l’avons disponible.

Caractéristiques

Tous les modes d’emploi pour Makita Visseuses
Plus de modes d’emploi de Visseuses

Foire aux questions sur Makita 6824 Visseuse

Notre équipe d’assistance recherche des informations utiles sur les produits et des réponses aux questions fréquemment posées. Si vous trouvez une inexactitude dans notre foire aux questions, veuillez nous le faire savoir en utilisant notre formulaire de contact.

Produits connexes

Mode d’emploi

Makita BFT124F Visseuse

Mode d’emploi

Makita DFS450 Visseuse

Mode d’emploi

Makita FS2200 Visseuse

Mode d’emploi

Makita DFT124R Visseuse

Mode d’emploi

Makita BFL061F Visseuse

Mode d’emploi

Makita BFL121F Visseuse

Mode d’emploi

Makita FS2700 Visseuse

Mode d’emploi

Makita DF001D Visseuse

Catégories associées