Mode d’emploi Makita EH7500S Taille-haies

Mode d’emploi

5

Starting up the Hedge Trimmer

- Please make sure that there are no children or other people within a working

range of 15 meters (5), also pay attention to any animals in the working vicinity.

- Before operating, always check that the Hedge Trimmer is safe for operation:

- Check the security of the throttle lever. The throttle lever should be checked for

smooth and easy action. Check for proper functioning of the throttle lever lock.

Check for clean and dry handles and test the function of the I-O Switch. Keep

handles free of oil and fuel.

Start the Hedge Trimmer only in accordance with the instructions.

Do not use any other methods for starting the engine (6)!

- Use the Hedge Trimmer only for applications specied.

- Start the Hedge Trimmer engine only after the entire assembly is done. Operation

of the Hedge Trimmer is permitted only after all the appropriate accessories are

attached!

- Before starting, make sure that the cutter blade will not contact any objects such

as branches, stones, etc.

- The engine is to be stopped immediately if there are any engine problems.

- When working with the Hedge Trimmer, keep both hands on handles always

wrap your ngers tightly around the handle, keeping the control handle cradled

between your thumb and forenger. Keep your hand in this position to have your

machine under control at all times. Make sure your control handle is in good

condition and free of moisture, pitch, oil or grease.

Always ensure a safe, well-balanced footing.

- Only use outdoors.

- Always be aware of your surroundings and stay alert for possible hazards that

you may not hear due to the noise of the machine.

- Operate the Hedge Trimmer in such a manner as to avoid inhalation of the

exhaust gases. Never run the engine in enclosed rooms (risk of suffocation and

gas poisoning). Carbon monoxide is an odorless gas. Always ensure there is

adequate ventilation.

- Stop the engine when resting and when leaving the Hedge Trimmer unattended.

Place it in a safe location to prevent danger to others, setting re to combustible

materials or damage to the machine.

- Never lay down the hot Hedge Trimmer onto dry grass or onto any combustible

materials.

- To reduce re hazard keep engine and silencer free of debris, leaves, or

excessive lubricant;

- Never operate the engine with a faulty exhaust mufer.

- Stop the engine during transport (7).

- Stop the engine or disconnect from mains before:

- Cleaning or when cleaning a blockage;

- Checking, maintenance or working on the machine.

- Position the Hedge Trimmer safely during car or truck transportation to avoid fuel

leakage.

- When transporting the Hedge Trimmer ensure that the fuel tank is completely

empty to avoid fuel leakage.

- When transporting or storing the machine always t the cutting device guard.

Refuelling

- Stop the engine before refuelling (7), keep well away from open ame (8) and do

not smoke.

- Do not attempt to refuel a hot or a running engine.

- Avoid skin contact with petroleum products. Do not inhale fuel vapor. Always

wear protective gloves during refuelling. Change and clean protective clothing at

regular intervals.

- Take care not to spill either fuel or oil in order to prevent soil contamination

(environmental protection). Clean the Hedge Trimmer immediately after fuel has

been spilt. Allow wet cloths to dry before disposing in proper, covered container to

prevent spontaneous combustion.

- Avoid any fuel contact with your clothing. Change your clothing immediately if fuel

has been spilled on it (danger hazard).

- Inspect the fuel cap at regular intervals making sure that it stays securely fastened.

- Carefully tighten the fuel tank cap. Change locations to start the engine (at least 3

meters away from the place of refuelling) (9).

- Never refuel in closed rooms. Fuel vapors accumulate at ground level (risk of

explosions).

- Only transport and store fuel in approved containers. Make sure stored fuel is not

accessible to children.

- When mixing gasoline with two-stroke engine oil, use only gasoline which

contains no ethanol or methanol (types of alcohol).

This will help to prevent damage to fuel lines and other engine parts.

15 meters

(50 feet)

360°

(5)

(6)

(7)

• Resting

• Transporting

• Refuelling

• Maintenance

• Tool Replacement

(8)

(9)

3 meters

(10 feet)

Évaluation

En savoir plus sur ce mode d’emploi

Nous comprenons qu’il est agréable d’avoir un mode d’emploi papier pour vos Makita EH7500S Taille-haies. Vous pouvez toujours télécharger le mode d’emploi depuis notre site Web et l’imprimer vous-même. Si vous souhaitez disposer d’un mode d’emploi original, nous vous recommandons de contacter Makita. Ils pourront peut-être fournir un mode d’emploi original. Recherchez-vous le mode d’emploi de votre Makita EH7500S Taille-haies dans une autre langue ? Choisissez votre langue préférée sur notre page d’accueil et recherchez le numéro de modèle pour voir si nous l’avons disponible.

Caractéristiques

Tous les modes d’emploi pour Makita Taille-haies
Plus de modes d’emploi de Taille-haies

Foire aux questions sur Makita EH7500S Taille-haies

Notre équipe d’assistance recherche des informations utiles sur les produits et des réponses aux questions fréquemment posées. Si vous trouvez une inexactitude dans notre foire aux questions, veuillez nous le faire savoir en utilisant notre formulaire de contact.

Produits connexes

Mode d’emploi

Makita UH006GZ Taille-haies

Mode d’emploi

Makita DUH651Z Taille-haies

Mode d’emploi

Makita UH008GM201 Taille-haies

Mode d’emploi

Makita HTR4900 Taille-haies

Mode d’emploi

Makita DUM111ZX Taille-haies

Mode d’emploi

Makita EH7500W Taille-haies

Mode d’emploi

Makita UH4260 Taille-haies

Mode d’emploi

Makita DUH506 Taille-haies

Catégories associées