Mode d’emploi Maktec MT963 Meuleuse angulaire

Mode d’emploi

7

FUNCTIONAL DESCRIPTION

CAUTION:

• Always be sure that the tool is switched off and

unplugged before adjusting or checking function on the

tool.

Shaft lock (Fig. 1)

CAUTION:

• Never actuate the shaft lock when the spindle is mov-

ing. The tool may be damaged.

Press the shaft lock to prevent spindle rotation when

installing or removing accessories.

Switch action (Fig. 2)

CAUTION:

• Before plugging in the tool, always check to see that

the slide switch actuates properly and returns to the

“OFF” position when the rear of the slide switch is

depressed.

• Switch can be locked in “ON” position for ease of oper-

ator comfort during extended use. Apply caution when

locking tool in “ON” position and maintain firm grasp on

tool.

To start the tool, slide the switch lever toward the “I (ON)”

position. For continuous operation, press the front of the

switch lever to lock it.

To stop the tool, press the rear of the switch lever, then

slide it toward the “O (OFF)” position.

ASSEMBLY

CAUTION:

• Always be sure that the tool is switched off and

unplugged before carrying out any work on the tool.

Installing side grip (handle) (Fig. 3)

CAUTION:

• Always be sure that the side grip is installed securely

before operation.

Screw the side grip securely on the position of the tool as

shown in the figure.

Installing or removing wheel guard

(For depressed center wheel, multi disc /

abrasive cut-off wheel, diamond wheel) (Fig. 4)

CAUTION:

• The wheel guard must be fitted on the tool so that the

closed side of the guard always points toward the oper-

ator.

Mount the wheel guard with the protrusion on the wheel

guard band aligned with the notch on the bearing box.

Then rotate the wheel guard to such an angle that it can

protect the operator according to work. Be sure to tighten

the screw securely.

To remove wheel guard, follow the installation procedure

in reverse.

Installing or removing depressed center grinding

wheel/Multi-disc

WARNING:

• Always use supplied guard when depressed center

grinding wheel/Multi-disc is on tool. Wheel can shatter

during use and guard helps to reduce chances of per-

sonal injury.

Mount the inner flange onto the spindle. Fit the wheel/

disc on the inner flange and screw the lock nut onto the

spindle. (Fig. 5)

To tighten the lock nut, press the shaft lock firmly so that

the spindle cannot revolve, then use the lock nut wrench

and securely tighten clockwise.

To remove the wheel, follow the installation procedure in

reverse. (Fig. 6)

WARNING:

• Only actuate the shaft lock when the spindle is not

moving.

OPERATION

WARNING:

• It should never be necessary to force the tool. The

weight of the tool applies adequate pressure. Forcing

and excessive pressure could cause dangerous wheel

breakage.

• ALWAYS replace wheel if tool is dropped while grind-

ing.

• NEVER bang or hit grinding disc or wheel onto work.

• Avoid bouncing and snagging the wheel, especially

when working corners, sharp edges etc. This can

cause loss of control and kickback.

• NEVER use tool with wood cutting blades and other

saw blades. Such blades when used on a grinder fre-

quently kick and cause loss of control leading to per-

sonal injury.

CAUTION:

• After operation, always switch off the tool and wait until

the wheel has come to a complete stop before putting

the tool down.

Grinding and sanding operation (Fig. 7)

ALWAYS hold the tool firmly with one hand on housing

and the other on the side handle. Turn the tool on and

then apply the wheel or disc to the workpiece.

In general, keep the edge of the wheel or disc at an angle

of about 15 degrees to the workpiece surface.

During the break-in period with a new wheel, do not work

the grinder in the B direction or it will cut into the work-

piece. Once the edge of the wheel has been rounded off

by use, the wheel may be worked in both A and B direc-

tion.

Évaluation

En savoir plus sur ce mode d’emploi

Nous comprenons qu’il est agréable d’avoir un mode d’emploi papier pour vos Maktec MT963 Meuleuse angulaire. Vous pouvez toujours télécharger le mode d’emploi depuis notre site Web et l’imprimer vous-même. Si vous souhaitez disposer d’un mode d’emploi original, nous vous recommandons de contacter Maktec. Ils pourront peut-être fournir un mode d’emploi original. Recherchez-vous le mode d’emploi de votre Maktec MT963 Meuleuse angulaire dans une autre langue ? Choisissez votre langue préférée sur notre page d’accueil et recherchez le numéro de modèle pour voir si nous l’avons disponible.

Caractéristiques

Tous les modes d’emploi pour Maktec Meuleuses angulaires
Plus de modes d’emploi de Meuleuses angulaires

Foire aux questions sur Maktec MT963 Meuleuse angulaire

Notre équipe d’assistance recherche des informations utiles sur les produits et des réponses aux questions fréquemment posées. Si vous trouvez une inexactitude dans notre foire aux questions, veuillez nous le faire savoir en utilisant notre formulaire de contact.

Produits connexes

Mode d’emploi

Maktec MT904 Meuleuse angulaire

Mode d’emploi

Maktec MT905 Meuleuse angulaire

Mode d’emploi

Maktec MT903 Meuleuse angulaire

Mode d’emploi

Maktec MT961 Meuleuse angulaire

Mode d’emploi

Maktec MT962 Meuleuse angulaire

Mode d’emploi

Maktec MT902 Meuleuse angulaire

Mode d’emploi

Vito VIRE12510A Meuleuse angulaire

Mode d’emploi

Milwaukee 2686-20 Meuleuse angulaire

Catégories associées