Mode d’emploi Maytag WVW51UC6FS Hotte aspirante

Mode d’emploi

4

INSTALLATION REQUIREMENTS

Tools and Parts

Gather the required tools and parts before starting

installation. Read and follow the instructions provided

with any tools listed here.

Tools Needed

■ Level

■ Drill with 1

1

/

4

" (3.2 cm),

1

/

8

" (3.2 mm),

and

5

/

16

" (7.9 mm) drill bits

■ Pencil

■ Wire stripper or utility knife

■ Tape measure or ruler

■ Pliers

■ Caulking gun and weatherproof caulking compound

■ Vent clamps

■ Jigsaw or keyhole saw

■ Flat-blade screwdriver

■ Metal snips

■ Phillips screwdriver

Parts Needed

■ Home power supply cable

■

1

/

2

" (12.7 mm) UL listed or CSA approved strain relief

■ 3 UL listed wire connectors

For Vented Installations, You Will Also Need:

■ 1 wall or roof cap

■ Metal vent system

For Non-Vented (Recirculating) Installations,

You Will Also Need:

■ Recirculation Kit Part Number W10294733 for non-vented

(recirculating) installations only. See “Assistance or Service”

section to order.

■ 6" (15.2 cm) diameter round metal vent duct -

length required is determined by ceiling height.

Parts Supplied

Remove parts from packages. Check that all parts are included.

■ Hood canopy assembly with blower, LED lights and

canopy glass already installed

■ Vent transition with back draft dampers installed

■ Vent cover support bracket

■ Metal grease filter

■ Mounting template

■ 2-piece vent cover

■ 2 - 3.5 x 9.5 mm mounting screws (Phillips)

■ 4 - 4.2 x 8 mm screws (T20

®†

drive)

■ 6 - 5 x 45 mm mounting screws (#2 Phillips)

■ 4 - 5.4 x 75 mm screws (Phillips) (for 10 x 60 mm

wall anchors)

■ 2 - 8 x 40 mm wall anchors

■ 4 - 10 x 60 mm wall anchors

■ T20

®

Torx

®†

adapter

Location Requirements

IMPORTANT: Observe all governing codes and ordinances.

Have a qualified technician install the range hood. It is the

installer’s responsibility to comply with installation clearances

specified on the model/serial/rating plate. The model/serial/

rating plate is located behind the left filter on the rear wall

of the vent hood.

Canopy hood location should be away from strong draft areas,

such as windows, doors, and strong heating vents.

Cabinet opening dimensions that are shown must be used.

Given dimensions provide minimum clearance.

This range hood is recommended for use with cooktops with

a maximum total rating of 60,000 BTUs or less.

Grounded electrical outlet is required. See “Electrical

Requirements” section.

The canopy hood is factory set for venting through the roof or

wall. For non-vented (recirculating) installation, see “For non-

vented (recirculating) installation only” in the “Connect Vent

System” section. Recirculation Kit Part Number W10294733

is available from your dealer or an authorized parts distributor.

All openings in ceiling and wall where canopy hood will be

installed must be sealed.

For Mobile Home Installations

The installation of this range hood must conform to the

Manufactured Home Construction Safety Standards, Title

24 CFR, Part 328 (formerly the Federal Standard for Mobile

Home Construction and Safety, Title 24, HUD, Part 280)

or, when such standard is not applicable, the standard for

Manufactured Home Installation 1982 (Manufactured Home

Sites, Communities and Setups) ANSI A225.1/NFPA 501A,

or latest edition, or with local codes.

Product Dimensions

20"

(50.8 cm)

30" (76.2 cm) or

36" (91.4 cm)

13³⁄₁₆"

(33.5 cm)

10

⁷⁄₈

"

(27.6 cm)

†

®

TORX and T20 are registered trademarks of Acument Intellectual Properties, LLC.

Évaluation

En savoir plus sur ce mode d’emploi

Nous comprenons qu’il est agréable d’avoir un mode d’emploi papier pour vos Maytag WVW51UC6FS Hotte aspirante. Vous pouvez toujours télécharger le mode d’emploi depuis notre site Web et l’imprimer vous-même. Si vous souhaitez disposer d’un mode d’emploi original, nous vous recommandons de contacter Maytag. Ils pourront peut-être fournir un mode d’emploi original. Recherchez-vous le mode d’emploi de votre Maytag WVW51UC6FS Hotte aspirante dans une autre langue ? Choisissez votre langue préférée sur notre page d’accueil et recherchez le numéro de modèle pour voir si nous l’avons disponible.

Caractéristiques

Tous les modes d’emploi pour Maytag Hottes aspirantes
Plus de modes d’emploi de Hottes aspirantes

Foire aux questions sur Maytag WVW51UC6FS Hotte aspirante

Notre équipe d’assistance recherche des informations utiles sur les produits et des réponses aux questions fréquemment posées. Si vous trouvez une inexactitude dans notre foire aux questions, veuillez nous le faire savoir en utilisant notre formulaire de contact.

Produits connexes

Mode d’emploi

Maytag UXT4230ADW Hotte aspirante

Mode d’emploi

Maytag UXT4230ADB Hotte aspirante

Mode d’emploi

Maytag UXT4236ADW Hotte aspirante

Mode d’emploi

Maytag UXT5230BDS Hotte aspirante

Mode d’emploi

Maytag UXT4030ADW Hotte aspirante

Mode d’emploi

Maytag WVW57UC6FS Hotte aspirante

Mode d’emploi

Maytag UXT3030ADW Hotte aspirante

Mode d’emploi

Maytag GXU7130DXS Hotte aspirante

Catégories associées