Mode d’emploi Medisana BU 540 Connect Tensiomètre

Mode d’emploi

Ÿ The unit is intended only for private use in the home.

Ÿ Do not use the unit in case of existing polyester resp. synthetic allergies.

Ÿ The device should be placed at least 30 minutes before use in the area of use in

order to properly adapt to the room temperature. Only use the device under the

conditions mentioned in the technical details.

Ÿ Consult your doctor prior to using the blood pressure monitor if you are

concerned about health matters.

Ÿ Only use the unit for its intended purpose in accordance with the instructions

for use.

Ÿ Warranty claims become void if the unit is misused.

Ÿ The unit may not be used to check the heart rate of a pacemaker.

Ÿ Irregularity of pulse or arrhythmia can lead to difficulties in recording a correct

reading when measurements are taken using oscillometric blood pressure

devices. This device is electronically equipped to detect arrhythmia which it

indicates with the icon . In this case, contact your physician.

Ÿ Like on any other oscillometric blood pressure measurement devices, certain

medical conditions can affect the measurement accuracy, among others:

cardiac arrhythmias, low blood pressure, circulatory disorders, states of shock,

diabetes, pregnancy, pre-eclampsy etc. Always consult a physician before you

use the device.

Ÿ Never apply the cuff over hurt skin.

Ÿ Do not take measurements, if any other equipment is applied to the same limb

for monitoring. This could lead to disturbances or failures.

Ÿ If you experience discomfort during a measurement, such as pain in the upper

arm or other complaints, press the START/ STOP button to release the air

immediately from the cuff. Loosen the cuff and remove it from your arm.

Ÿ On the rare occasion of a fault causing the cuff to remain fully inflated during

measurement, open the cuff immediately. Prolonged high pressure (cuff

pressure >300 mmHg or constant pressure >15 mmHg for more than 3

minutes) applied to the arm may lead to an ecchymosis.

Ÿ Too frequent and consecutive measurements could cause disturbances in

blood circulation and injuries.

Ÿ Pay attention during use and storage, that cable and air hose will not cause

strangulation.

Ÿ Never bend the air hose during use as this may lead to injuries. Also never

squeeze or block the air hose in any way.

Ÿ Do not connect the air hose to other medical equipment, as this could cause air

to be pumped into intravascular systems or high pressure, what could lead to

dangerous injuries.

Ÿ This device is not suitable for continous monitoring during medical

emergencies or operations.

Ÿ This device is not intended for patient transports outside a healthcare facility.

Ÿ This device cannot be used with surgical equipment at the same time.

Ÿ Do not take any therapeutic measures on the basis of a self measurement.

Never alter the dose of a medicine prescribed by a doctor.

Ÿ The unit may not be operated in the vicinity of appliances that emit strong

electric radiation such as radio transmitters or mobile phones. This may affect

the proper functioning (see "electromagnetic compatibility").

Ÿ Do not use the equipment where flammable gas (such as anaesthetic gas,

oxygen or hydrogen) are present.

Ÿ Replace all of the batteries simultaneously!

Ÿ Please do not attempt to repair the unit yourself in the event of malfunctions.

Only have repairs carried out by authorised service centres.

Ÿ If the unit is not going to be used for a long period, please remove the batteries.

Ÿ Only replace with batteries of the same type, never use different types of

batteries together or used batteries with new ones!

Ÿ Do not disassemble batteries!

Ÿ Do not attempt to recharge these batteries! There is a danger of explosion!

Ÿ If a battery has been swallowed seek medical attention immediately!

Ÿ Only use original additional or spare parts from the manufacturer. Other parts

could damage the device or could lead to personal injury.

Ÿ Insert the batteries correctly, observing the polarity!

Ÿ Before use, make sure the device functions safely and is in proper working

condition. Do not service or maintain while the device is in use.

Ÿ Increased risk of leakage, avoid contact with skin, eyes and mucous

membranes! If battery acid comes in contact with any of these parts, rinse the

affected area with copious amounts of fresh water and seek medical attention

immediately!

Ÿ This device is intended to be used by adults. The unit is unsuitable for children

or babies. Contact your doctor, if you want to use this device on young persons.

Ÿ Please ensure that the unit is kept away from the reach of children and pets.

The swallowing of small part like packaging bag, battery, battery cover and so

on may cause suffocation.

Ÿ Protect the unit from moisture. Should moisture enter the unit, remove the

batteries and stop using it immediately. In this case, please contact either your

dealer or us directly. You can find details of how to contact us on the address

page.

Ÿ Please report to MEDISANA if any unexpected operation or events occur.

Ÿ Remove discharged batteries from the device immediately!

Ÿ Do not short circuit! There is a danger of explosion!

Ÿ Do not throw into a fire! There is a danger of explosion!

Ÿ This device is not designed to be used by persons with limited physical,

sensory or mental abilities, or by persons with insufficient experience and/or

knowledge, unless under observation by a person responsible for their safety,

or unless they have been instructed in the use of the device.

Ÿ Keep batteries out of children's reach!

Ÿ Do not throw used batteries into the household refuse; put them in a hazardous

waste container or take them to a battery collection point, at the shop where

they were purchased!

Ÿ Remove the batteries from the device if it is not going to be used for an

extended period!

8

Please contact the service centre if you can’t solve the problem.

Do not disassemble the unit by yourself.

z

BATTERY SAFETY INFORMATION

1

9

q

Unit and LC-display

Connector for the hose Air hose Battery compartment (on backside)

Cuff User memory button "MEM" - button (Memory) "SET" -

button START/STOPP - button LC - display

Display of systolic pressure Display of diastolic pressure

Display of pulse rate Time/Date - Symbol Bluetooth

®

Inflation / Deflation symbol Pulse / Arrhythmia display

Batteries low Average value display (“AVG“) User memory (A/B)

Blood Pressure Indicator (green - yellow - orange - red) Memory display

i

p

2

3

6

4

5

7

8

0

w

e

r

z

t

u

o

a

Items supplied

Please check first of all that the unit is complete.

The following parts are included as standard:

• 1 MEDISANA blood pressure monitor BU 540 connect

• 1 cuff with air tube

• 4 batteries (type AAA, LR03) 1.5 V

• 1 instruction manual and EMV leaflet

Please contact your supplier if you notice any transport damage on unpacking

the unit.

WARNING

Please ensure that the polythene packing is kept away from the

reach of children! Risk of suffocation!

How is blood pressure measured?

The MEDISANA upper arm blood pressure monitor BU 540 connect is a blood

pressure unit which is used to measure blood pressure at the upper arm. The

measurement is carried out by a microprocessor - already during the inflating

process of the cuff. The device detects the systole and the measurement is

completed earlier than using conventional measurement methods. As a result, an

unnecessarily excessive inflation pressure in the cuff is prevented. Additionally,

your device is able to recognize unregular heartbeat (so-called arrhythmia), which

may affect the measurements. In case an arrhythmia has been deteced, the

respective symbol will appear in the display of the unit.

WARNING

Blood pressure classification according to WHO

These values have been specified by the World Health Organisation (WHO)

without making any allowance for age.

Blood pressure that is too low represents just as great a health

risk as blood pressure that is too high! Fits of dizziness may

lead to dangerous situations arising (e.g. on stairs or in traffic)!

≥ 180 ≥ 110

160 - 179 100 - 109

140 - 159 90 - 99

130 - 139 85 - 89

120 - 129 80 - 84

< 120 < 80

serious

hypertension

medium

hypertension

mild

hypertension

high-normal

blood pressure

normal

blood pressure

optimal

blood pressure

p

systolic diastolic

mmHg mmHg

Bloodpressure Indi-

cator

red

orange

yellow

green

green

green

Influencing and evaluating readings

•

Measure your blood pressure several times, then record and compare the

results. Do not draw any conclusions from a single reading.

Your blood pressure readings should always be evaluated by a doctor who is

also familiar with your personal medical history. When using the unit regularly

and recording the values for your doctor, you should visit the doctor from time to

time to keep him updated.

When taking readings, remember that the daily values are influenced by several

factors. Smoking, consumption of alcohol, drugs and physical exertion influence

the measured values in various ways.

Measure your blood pressure before meals.

Before taking readings, allow yourself at least five minutes rest.

If the systolic and diastolic readings seem unusual (too high or too low) on

several occasions, despite correct use of the unit, please inform your doctor. This

also applies to the rare occasions when an irregular or very weak pulse prevents

you from taking readings. i

•

•

•

•

•

Getting started

Inserting/changing batteries

appears on the display or if nothing appears on the display after the unit has

been switched on.

Close the battery compartment. Replace the batteries if the change battery symbol

You must insert the batteries provided before you can use your unit. The lid of the

battery compartment is located on the underside of the unit. Open it, remove it

and insert the 4 x 1,5 V batteries, type AAA / LR03 supplied. Ensure correct polarity

when inserting the batteries (as marked inside the battery compartment).

3

9u

Settings

1. Date and time:

When unit is switched off, press SET . The time will be displayed. Now press and

hold the SET button , until the year figure starts to flash for setting. Keep

pressing the MEM button until the actual year figure appears. Press SET to

confirm the year. Afterwards, you can proceed with the month/date setting,

followed by the time format setting (12 or 24 hours), as well as hours and minutes.

Adjust the corresponding figures accordingly. When finished, “dOnE” appears on

the display along with the adjusted values. Afterwards, the device will switch off.

7

7

7

6

2. User memory setting:

The MEDISANA upper arm blood pressure monitor BU 540 connect features

2 separate memories, each with a capacity of 250 memory slots. By pressing the

user memory button when the device is switched on, you may choose between

user and user . The display shows the current selection .

Fitting the cuff

1.

2.

3.

4.

5.

6.

Correct measuring position for sitting (Fig.3).

Measure the pulse on your bare arm.

Only position the cuff on the right arm if it cannot be used on the left arm. Always

carry out measurements on the same arm.

Slide the open end of the cuff through the metal bracket so that the Velcro

fastener is on the outside and it becomes a cylindrical form (Fig.1). Slide the

cuff over your left upper arm.

Push the end piece of the air tube into the hole on the left side of the unit

prior to use.

Position the air hose in the middle of your arm in line with your middle finger

(Fig.2) (a). The lower edge of the cuff should be 2 - 3 cm above the crease of the

elbow. (b). Pull the cuff tight and close the Velcro fastener (c).

3

Taking a blood pressure measurement

After the cuff has been appropriately positioned,the measurement can begin.

All display characters are shown (display test). This test can be used to check

that the display is indicating properly and in full. The unit is ready for

measurement and „0“ appears.

The device then automatically inflates the cuff slowly in order to measure your

blood pressure. The rising pressure in the cuff is shown on the display.

When the device detects the signal, the heart symbol on the display starts to

flash. If a result is determined, the device slowly will release the air from the cuff.

The systolic and diastolic blood pressure and the pulse value with the time value

appear on the display.

The blood pressure indicator flashes next to the relevant coloured bar

depending on the WHO blood pressure classification.

Switch the unit on by pressing the START/STOP button .

The readings are automatically saved in the selected memory ( or ).

Switch off the device using the START/STOP button .

appears additionally.

The measurement results will automatically be transferred via Bluetooth to

®

receiveready devices. During this process, the Bluetooth -symbol will

®

flash. If the transfer was successful, the Bluetooth -symbol will disappear

®

after approx. 5 seconds. If the transfar was not successful, the symbol will

disappear after max. 3 minutes.

If the unit has detected an irregular heartbeat, the arrhythmia display

1.

2.

3.

4.

5.

6.

7.

8.

9.

8

The MEDISANA Blood Pressure monitor BU 540 connect offers the possibility

to transfer your measured values via Bluetooth to the VitaDock app. The

® ®

VitaDock app allows the evaluation, storage and synchronisation of your data

®

between multiple iOS- and Android-devices to have access to it anytime and

anywhere. You may share your results with your friends or your doctor. Therefore

you need a free user account, which you can create on the website

www.vitadock.com. For Android or iOS mobile devices, you may download the

respective apps. You will find a detailed instruction for how to install and use the

software on the mentioned website.

After each measurement an automatic transfer of the values will take place

(provided that Bluetooth is activated and configurated on the receiving device).

®

p

z

r

r

8

®

Transfer via Bluetooth

WARNING

Ÿ To avoid interference with other electronic devices, these

should be kept at least 1 meter away from the monitor.

Ÿ Keep the device at least 20 centimeters away from the

human body (especially the head) when the Bluetooth data

®

transmission is proceeding after measurement.

Ÿ The distance between the device and the receiver should be

between 1 meter to 10 meters to avoid possible

disturbances.

Displaying stored results

This unit features 2 separate memories, each with a capacity of 250 memory slots.

Results are automatically stored in the memory selected by the user. Press the

MEM button when power off, to call up the measured values stored. The

average values of the last 3 measurements appear on the display (if already 3

measurements have been stored for the respective user).

Press the MEM button again to call up the last measurement value. Repeatedly

pressing the MEM button displays the respective values measured previously.

Memory recall mode can be exited at any time by pressing the START/STOP

button , which will also switch the unit off. The oldest value is deleted if 250

measured values have been stored in the memory and a new value is saved.

6

Deleting memory

Press MEM-button to enter the memory recall mode.

If you are sure that you want to permanently remove all stored memories, press

and hold the SET button for approximately 3 seconds until „dEL ALL” appears in

the display. Then press SET button again to delete all the values. The device

then switches off automatically. You may abort the deletion process by pressing the

START/STOP button beforehand.

6

7

6

8

8

Error messages and error remedying

Display Cause Solution

No display

Batteries may be ex-

hausted or inserted incor-

rectly. Check if the power

connection has been es-

tablished properly.

Insert new batteries.

Insert the batteries according to

the instructions given.

+ Lo

Weak batteries

Batteries are weak or empty.

Replace all 4 batteries by new

ones (1.5V, type AAA / LR03).

Cuff not properly fitted

Movement or speaking

during measurement

Pulse cannot be detected

Measurement failed

Calibration error

(“xx“ can be a figure,

e.g. 01, 02 etc.)

Out of measurement

range

Wrap the cuff properly.

Remeasure in correct way.

Rest 30 minutes and remeasure

in correct way. Do not speak or

move during the measurement.

Wrap the cuff properly. Loosen

the clothing on the arm.

Remeasure in correct way.

Wrap the cuff properly.

Remeasure in correct way.

Wrap the cuff properly.

Remeasure in correct way.

Relax for a moment. Refasten

the cuff and measure again.

If the problem persists, contact

your physician.

E01

E02

E03

E04

EExx

Name and description

Model

Display system

Memory slots

Measuring method

Power supply

Blood pressure measuring range

Pulse measuring range

Maximum error tolerance for static pressure

Maximum error tolerance for pulse rate

Pressure generation

Deflation

Protection marking against particles and water

Operating conditions

Storage conditions

Dimensions (L x W x H)

Cuff

Weight (main unit)

Item number

EAN number

Acessories

MEDISANA Blood pressure monitor

BU 540 connect

TMB-1490-BS

Digital display

2 x 250 measurement values

Oscillometric

6 V=, 4 x 1,5 V batteries AAA LR03

0 – 299 mmHg

40 – 199 beats/min.

± 3 mmHg

± 5 % of the value

Automatic with pump

Automatic

IP21

+5 °C to +40 °C, 15 to 90 % max. relative humidity,

700-1060 hPa atmospheric pressure

-20 °C to +60 °C, to 93 % max. relative humidity,

non-condensing

approx. 140 x 130 x 60 mm

22 - 42 cm for adults

approx. 250 g without batteries

51182

40 15588 51182 0

Spare cuff

Art. No. 51299 / EAN 40 15588 51299 5

:

:

:

:

:

:

:

:

:

:

:

:

:

:

:

:

:

:

:

:

:

Technical specifications

Guangdong Transtek Medical Electronics Co., Ltd.

Zone A, No.105 ,Dongli Road, Torch Development District,

Zhongshan,528437,Guangdong,China

The service centre address is shown on the attached leaflet.

Distributed & imported by:

MEDISANA GmbH, Jagenbergstraße 1, 41468 NEUSS

Germany

EC REP

MDSS - Medical Device Safety Service GmbH

Address: Schiffgraben 41, 30175 Hannover, Germany

GB

Read the instruction manual carefully before

using this device, especially the safety

instructions, and keep the instruction manual

for future use. Should you give this device to

another person, it is vital that you also pass on

these instructions for use.

Safety Instructions

o

5

6

7

Disposal

This product must not be disposed of together with domestic waste. All users

are obliged to hand in all electrical or electronic devices, regardless of

whether or not they contain toxic substances, at a municipal or commercial

collection point so that they can be disposed of in an environmentally accep-

table manner.

Remove the batteries before disposing of the device/unit. Do not dispose of old

batteries with your household waste, but at a battery collection station at a recyc-

ling site or in a shop. Consult your local authority or your supplier for information

about disposal.

Guidelines / Standards

This blood pressure monitor meets the requirements of the EU standard for non-

invasive blood pressure monitors. It is certified in accordance with EC Guidelines

and carries the CE symbol (conformity symbol) “CE 0123”.

The blood pressure monitor corresponds to European standards EN 60601-1, EN

60601-1-2, EN 1060-3, EN 81060-1 and EN 81060-2.

Electromagnetic compatibility: (see attached leaflet)

The specifications of EU Guideline “93/42/EEC of the Council Directive dated 14

June 1993 concerning medical devices” are met and likewise those of the RED

2014/53/EC. You can request the complete Conformity Declaration from Medisana

GmbH, Jagenbergstrasse 1, 41468 Neuss, Germany, or you can also download it

from the Medisana homepage (www.medisana.de).

In accordance with our policy of continual product improvement, we

reserve the right to make technical and visual changes without notice.

The current version of this instruction manual can be found under

www.medisana.com

Please contact your supplier or the service centre in case of a claim under the

warranty. If you have to return the unit, please enclose a copy of your receipt and

state what the defect is.

The following warranty terms apply:

1. The warranty period for MEDISANA products is 3 years from date of purchase.

In case of a warranty claim, the date of purchase has to be proven by means

of the sales receipt or invoice.

2. Defects in material or workmanship will be removed free of charge within the

warranty period.

3. Repairs under warranty do not extend the warranty period either for the unit

or for the replacement parts.

4. The following is excluded under the warranty:

a. All damage which has arisen due to improper treatment, e.g.

nonobservance of the user instructions.

b. All damage which is due to repairs or tampering by the customer or

unauthorised third parties.

c. Damage which has arisen during transport from the manufacturer to the

consumer or during transport to the service centre.

d. Accessories which are subject to normal wear and tear as batteries, cuff etc..

5. Liability for direct or indirect consequential losses caused by the unit are

excluded even if the damage to the unit is accepted as a warranty claim.

Warranty and repair terms

Intended use

Common factors of wrong measurements

•

This fully automatic electronic blood pressure monitor

is intended for measuring the blood pressure at

home. It is a non-invasive blood pressure measure-

ment system to measure the diastolic and systolic

blood pressure and pulse of an adult using a non-

invasive technique by means of a cuff, which needs to

be fitted on the upper arm.

It is intended for adult indoor use only.

The useable cuff circumference is 22 to 42 cm.

DE/GB

GB Unit and LC-Display

Blood Pressure Monitor

BU 540 connect

Instruction Manual

Please read carefully!

®

Contraindications

•

The device is not suitable for measuring the blood

pressure of children. Ask your doctor before using it

on older children.

The device is not suitable for use on pregnant women

and patients with implanted, electrocical devices (e.

g. pacemaker or defibrillator).

•

0123

•

0

q

w

e

r

t

z

u

i

o

a

p

6

7

8

4

2

1

3

9

1

2-3 cm

(a)

(b)

(c)

2

3

5

•

Please keep quiet for 5-10 minutes and avoid eating,

drinking alcohol, smoking, exercising and bathing

before taking a measurement. All these factors will

influence the measurement result.

Remove any garment that fits closely to your

upper arm.

Always measure on the same arm (normally left).

Measurements should be taken regularly at the

same time of each day, as the blood pressure varies

even during the day.

Any effort to support the arm during measurement

may increase the measured blood pressure.

Make sure, you are in a comfortable, relaxed position

and do not move or constrict your muscles

during measurement. Use a cushion to support your

arm if necessary.

If the arm artery lies lower or higher than the heart,

a false reading will be obtained.

A loose or open cuff causes false readings.

With repeated measurements, blood accumulates

in the arm which can lead to false reading.

Consecutive blood pressure measurements should

be repeated after 3 minutes pause or after the

arm has been held up in order to allow the

accumulated blood to flow away.

•

•

•

•

•

•

•

•

Explanation of symbols

IMPORTANT

Follow the instructions for use!

Non-observance of these instructions

can result in serious injury or damage

to the device.

WARNING

These warning notes must be observed

to prevent any injury to the user.

CAUTION

These notes must be observed to prevent

any damage to the device.

NOTE

These notes give you useful additional

information on the installation or

operation.

Device classification: type BF applied part

LOT number

Manufacturer

Date of manufacture

Serial number

SN

out

Cleaning and maintenance

Remove the batteries before cleaning the unit. Clean the unit using a soft cloth

lightly moistened with a mild soapy solution. Never use abrasive cleaning agents,

alcohol, naphta, thinner or gasoline etc.. Never immerse the unit or any component

in water. Be cautiious not to get any moisture in the main unit.

Do not wet the cuff or attempt to clean the cuff with water. Using a dry cloth, gently

wipe away any excess moisture that may remain on the cuff. Lay the cuff flat in an

unrolled position and allow the cuff to air dry.

Do not expose the unit to direct sunlight; protect it against dirt and moisture. Do not

expose the unit to extreme hot or cold temperatures. Keep the device in the

storage case when not in use. Store the unit in a clean and dry location.

Évaluation

En savoir plus sur ce mode d’emploi

Nous comprenons qu’il est agréable d’avoir un mode d’emploi papier pour vos Medisana BU 540 Connect Tensiomètre. Vous pouvez toujours télécharger le mode d’emploi depuis notre site Web et l’imprimer vous-même. Si vous souhaitez disposer d’un mode d’emploi original, nous vous recommandons de contacter Medisana. Ils pourront peut-être fournir un mode d’emploi original. Recherchez-vous le mode d’emploi de votre Medisana BU 540 Connect Tensiomètre dans une autre langue ? Choisissez votre langue préférée sur notre page d’accueil et recherchez le numéro de modèle pour voir si nous l’avons disponible.

Caractéristiques

Tous les modes d’emploi pour Medisana Tensiomètres
Plus de modes d’emploi de Tensiomètres

Foire aux questions sur Medisana BU 540 Connect Tensiomètre

Notre équipe d’assistance recherche des informations utiles sur les produits et des réponses aux questions fréquemment posées. Si vous trouvez une inexactitude dans notre foire aux questions, veuillez nous le faire savoir en utilisant notre formulaire de contact.

Produits connexes

Mode d’emploi

Medisana CardioCompact Tensiomètre

Mode d’emploi

Medisana BW A30 Tensiomètre

Mode d’emploi

Medisana MTP Pro Tensiomètre

Mode d’emploi

Medisana MTM Tensiomètre

Mode d’emploi

Medisana BU 584 Connect Tensiomètre

Mode d’emploi

Medisana BU 550 connect Tensiomètre

Mode d’emploi

Medisana BU 510 Tensiomètre

Mode d’emploi

Medisana HGB Tensiomètre

Catégories associées