Mode d’emploi Milwaukee 2529-21XC Scie à ruban

Mode d’emploi

5

OPERATION

WARNING

To reduce the risk of injury, always

wear proper eye protection marked

to comply with ANSI Z87.1.

When working in dusty situations, wear appro-

priate respiratory protection or use an OSHA

compliant dust extraction solution.

Always remove battery pack before changing

or removing accessories. Only use accessories

specically recommended for this tool. Others

may be hazardous.

Keep hands away from the blade and all mov-

ing parts.

Fuel Gauge

To determine the amount of charge left in the battery,

turn the tool ON. The Fuel Gauge will light up for 2-3

seconds. When less than 10% of charge is left, 1 light

on the fuel gauge will ash 4 times.

To signal the end of charge, 1 light on the fuel gauge

will ash 8 times and the tool will not run. Charge

the battery pack.

If the battery becomes too hot, the fuel gauge lights

will ash in an alternating pattern and the tool will not

run. Allow the battery to cool down.

Starting, Stopping and Controlling Speed

1. To start the tool, grasp the handle rmly. Push the

lock-o󰀨 button down, then pull the trigger. Allow the

motor to reach full speed before beginning the cut.

NOTE: An LED is turned on when the trigger is

pulled and will go o󰀨 shortly after the trigger is

released.

2. To vary the speed, increase or decrease the pres-

sure on the trigger. The further the trigger is pulled,

the greater the speed.

3. To stop the tool, release the trigger. Ensure the

tool has come to a complete stop before removing

the blade from a partial cut or laying the tool down.

Typical Application

1. Keep the blade o󰀨 the workpiece until the motor

has reached full speed.

2. Start cutting on a surface where the greatest num-

ber of teeth will be in contact with the workpiece

at one time.

Correct Incorrect

3. Place the material guide against the workpiece and

lower the moving saw blade into the cut.

4. Do not bear down while cutting.

5. When completing a cut, hold the tool rmly so it

will not fall against the workpiece.

MAINTENANCE

WARNING

To reduce the risk of injury, always

unplug the charger and remove the

battery pack from the charger or tool before

performing any maintenance. Never disassemble

the tool, battery pack or charger. Contact a

MILWAUKEE service facility for ALL repairs.

Maintaining Tool

Keep your tool, battery pack and charger in good

repair by adopting a regular maintenance program.

Inspect your tool for issues such as undue noise,

misalignment or binding of moving parts, breakage of

parts, or any other condition that may a󰀨ect the tool

operation. Return the tool, battery pack, and charger

to a MILWAUKEE service facility for repair. After six

months to one year, depending on use, return the

tool, battery pack and charger to a MILWAUKEE

service facility for inspection.

If the tool does not start or operate at full power with

a fully charged battery pack, clean the contacts on

the battery pack. If the tool still does not work prop-

erly, return the tool, charger and battery pack, to a

MILWAUKEE service facility for repairs.

WARNING

To reduce the risk of personal in-

jury and damage, never immerse

your tool, battery pack or charger in liquid or

allow a liquid to ow inside them.

Cleaning

Clean dust and debris from vents. Keep handles

clean, dry and free of oil or grease. Use only mild

soap and a damp cloth to clean, since certain clean-

ing agents and solvents are harmful to plastics and

other insulated parts. Some of these include gasoline,

turpentine, lacquer thinner, paint thinner, chlorinated

cleaning solvents, ammonia and household deter-

gents containing ammonia. Never use ammable or

combustible solvents around tools.

Repairs

For repairs, return the tool, battery pack and charger

to the nearest authorized service center.

ACCESSORIES

WARNING

Use only recommended accesso-

ries. Others may be hazardous.

For a complete listing of accessories, go online to

www.milwaukeetool.com or contact a distributor.

Évaluation

En savoir plus sur ce mode d’emploi

Nous comprenons qu’il est agréable d’avoir un mode d’emploi papier pour vos Milwaukee 2529-21XC Scie à ruban. Vous pouvez toujours télécharger le mode d’emploi depuis notre site Web et l’imprimer vous-même. Si vous souhaitez disposer d’un mode d’emploi original, nous vous recommandons de contacter Milwaukee. Ils pourront peut-être fournir un mode d’emploi original. Recherchez-vous le mode d’emploi de votre Milwaukee 2529-21XC Scie à ruban dans une autre langue ? Choisissez votre langue préférée sur notre page d’accueil et recherchez le numéro de modèle pour voir si nous l’avons disponible.

Caractéristiques

Tous les modes d’emploi pour Milwaukee Scies à ruban
Plus de modes d’emploi de Scies à ruban

Foire aux questions sur Milwaukee 2529-21XC Scie à ruban

Notre équipe d’assistance recherche des informations utiles sur les produits et des réponses aux questions fréquemment posées. Si vous trouvez une inexactitude dans notre foire aux questions, veuillez nous le faire savoir en utilisant notre formulaire de contact.

Produits connexes

Mode d’emploi

Milwaukee 6232-20 Scie à ruban

Mode d’emploi

Milwaukee 2529-20 Scie à ruban

Mode d’emploi

Milwaukee 2729S-20 Scie à ruban

Mode d’emploi

Milwaukee 6238-20 Scie à ruban

Mode d’emploi

Milwaukee 2629-20 Scie à ruban

Mode d’emploi

Milwaukee 2429-20 Scie à ruban

Mode d’emploi

Milwaukee 2829-22 Scie à ruban

Mode d’emploi

Milwaukee 2829S-22 Scie à ruban

Catégories associées