Mode d’emploi Milwaukee 5091 Meuleuse d'établi

Mode d’emploi

Page 6

GROUNDING

Grounded tools require a three wire extension cord. Double insulated

tools can use either a two or three wire extension cord. As the distance

from the supply outlet increases, you must use a heavier gauge exten-

sion cord. Using extension cords with inadequately sized wire causes

a serious drop in voltage, resulting in loss of power and possible tool

damage. Refer to the table at right to determine the required minimum

wire size.

The smaller the gauge number of the wire, the greater the capacity of the

cord. For example, a 14 gauge cord can carry a higher current than a 16

gauge cord. When using more than one extension cord to make up the

total length, be sure each cord contains at least the minimum wire size

required. If you are using one extension cord for more than one tool, add

the nameplate amperes and use the sum to determine the required mini-

mum wire size.

Guidelines for Using Extension Cords

• If you are using an extension cord outdoors, be sure it is marked

with the suffix “W-A” (“W” in Canada) to indicate that it is

acceptable for outdoor use.

• Be sure your extension cord is properly wired and in good

electrical condition. Always replace a damaged extension cord

or have it repaired by a qualified person before using it.

• Protect your extension cords from sharp objects, excessive

heat and damp or wet areas.

Grounded Tools:

Tools with Three Prong Plugs

Tools marked “Grounding Re-

quired” have a three wire cord and

three prong grounding plug. The

plug must be connected to a prop-

erly grounded outlet (See Figure A

and B). If the tool should electri-

cally malfunction or break down,

grounding provides a low resis-

tance path to carry electricity away

from the user, reducing the risk of

electric shock.

The grounding prong in the plug is

connected through the green wire

inside the cord to the grounding

system in the tool. The green wire

in the cord must be the only wire

connected to the tool's grounding

system and must never be attached

to an electrically “live” terminal.

Your tool must be plugged into an

appropriate outlet, properly in-

stalled and grounded in accor-

dance with all codes and ordi-

nances. If the plug and outlet look

like those in Figure A, your tool is

rated for use on less than 150

volts. If your plug and outlet look

like those in Figure B, your tool is

rated for use on 150 to 250 volts.

Temporary adapters are not avail-

able for this type of plug.

Figure C illustrates a temporary

adapter available for connecting

grounded plugs (Figure A) to two

prong outlets. The green rigid ear

or lug extending from the adapter

must be connected to a permanent

ground such as a properly

grounded outlet box or receptacle.

Simply remove the center screw

from the outlet, insert the adapter

and reattach the screw through

the green grounding ear to the out-

let. If in doubt of proper grounding,

call a qualified electrician. A tem-

porary adapter should only be

used until a properly grounded

outlet can be installed by a quali-

fied electrician. The Canadian Elec-

trical Code prohibits the use of

temporary adapters.

Fig. A

Fig. B

EXTENSION CORDS

Nameplate

Amperes

0 - 5

5.1 - 8

8.1 - 12

12.1 - 15

15.1 - 20

Extension Cord Length

25'

16

16

14

12

10

75'

16

14

12

10

10

100'

14

12

10

10

--

150'

12

10

--

--

--

200'

12

--

--

--

--

Recommended Minimum Wire Gauge

for Extension Cords*

* Based on limiting the line voltage drop to five

volts at 150% of the rated amperes.

50'

16

16

14

12

10

Improperly connecting the grounding wire can

result in the risk of electric shock. Check with a

qualified electrician if you are in doubt as to

whether the outlet is properly grounded. Do not

modify the plug provided with the tool. Never

remove the grounding prong from the plug. Do

not use the tool if the cord or plug is damaged. If

damaged, have it repaired by a

MILWAUKEE

service facility before use. If the plug will not fit

the outlet, have a proper outlet installed by a

qualified electrician.

WARNING!

Fig. C

Temporary

Adapter

Green Grounding Ear

Évaluation

En savoir plus sur ce mode d’emploi

Nous comprenons qu’il est agréable d’avoir un mode d’emploi papier pour vos Milwaukee 5091 Meuleuse d'établi. Vous pouvez toujours télécharger le mode d’emploi depuis notre site Web et l’imprimer vous-même. Si vous souhaitez disposer d’un mode d’emploi original, nous vous recommandons de contacter Milwaukee. Ils pourront peut-être fournir un mode d’emploi original. Recherchez-vous le mode d’emploi de votre Milwaukee 5091 Meuleuse d'établi dans une autre langue ? Choisissez votre langue préférée sur notre page d’accueil et recherchez le numéro de modèle pour voir si nous l’avons disponible.

Caractéristiques

Tous les modes d’emploi pour Milwaukee Meuleuses d'établi
Plus de modes d’emploi de Meuleuses d'établi

Foire aux questions sur Milwaukee 5091 Meuleuse d'établi

Notre équipe d’assistance recherche des informations utiles sur les produits et des réponses aux questions fréquemment posées. Si vous trouvez une inexactitude dans notre foire aux questions, veuillez nous le faire savoir en utilisant notre formulaire de contact.

Produits connexes

Mode d’emploi

Milwaukee 4991 Meuleuse d'établi

Mode d’emploi

Milwaukee 4931 Meuleuse d'établi

Mode d’emploi

Milwaukee 4995 Meuleuse d'établi

Mode d’emploi

Milwaukee 5051 Meuleuse d'établi

Mode d’emploi

Milwaukee 4935 Meuleuse d'établi

Mode d’emploi

FERM BGM1002 Meuleuse d'établi

Mode d’emploi

Stayer E 150 C Meuleuse d'établi

Mode d’emploi

Bosch GBG 60-20 Meuleuse d'établi

Catégories associées