Reset
1. Do not attempt to modify the unit, modifying the unit may cause an accident.
2. Installation or servicing of the unit by persons without training and experience in
electronic equipment and automotive accessories may be dangerous and could
expose you to the risk of electric shock or other hazards.
3. Stop the vehicle before carrying out any operation that could interfere with your driving.
4. Keep the volume at a level which you could hear sounds from outside the vehicle.
5. Do not work in extremely high or low temperature. Be sure the temperature inside the
vehicle is between +60°C and -10°C before turning on your unit.
6. When replacing the fuse(s), the replacement must be of the same amperage as
shown on the fuse holder.
7. Do not block vents or radiator panels. Blocking them will cause heat to build up inside
and may result in re.
8. Using this unit without running the engine can result in battery drainage.
9. Use only in cars with a 12 volt negative ground.
10. After completing the installation or replacing the car battery, you need to RESET the
unit before using it. Press RES button on the front panel with pointed object (such as
ball-point pen) to reset the unit to its initial settings.
GB - 1
PRECAUTIONS UNPACK YOUR UNIT CONNECTION
INSTALLATION LOCATION OF CONTROLS BASIC OPERATIONS LISTENING TO THE RADIO
SOUND FEATURES
GB - 2 GB - 3
Do not connect the ignition wire (red) and the battery wire (yellow), it may cause
a short circuit, even result in re.
GB - 4 GB - 5 GB - 6
When you unpack your new car radio, make sure that you have removed all the
accessories and information papers:
Main unit
User manual
Accessories:
GB - 7
English
1. Button: To turn unit on /off
2. : To hang up the call; MODE button
3. VOLUME / SEL / PTY knob
4. RESET button
5. LCD display
6. USB port
7. SD/MMC card slot
8. button
9. EQ: To select desired sound effects: FLAT /CLASSIC /ROCK / JAZZ / POP;
LOUD: Loudness On/Off
10. : To answer the phone/redial call; BAND button (To select band: FM1, FM2, FM3)
and AMS button
11. button
12. Built-in microphone
13. 1 / button: To select preset channel 1 in radio mode. To start or pause playback.
14. 2 / INT button: To select preset channel 2 in radio mode/transfer call. To start/ cancel
intro playback.
15. 3 / RPT button: To select preset channel 3 in radio mode. To repeat playback.
16. 4 / RDM button: To select preset channel 4 in radio mode. To start/ cancel random
playback.
17. 5 / -10 button: To select preset channel 5 in radio mode; To skip backward 10 tracks
(mp3 only)
18. 6 / +10 button: To select preset channel 6 in radio mode; To skip forward 10 tracks
(mp3 only)
19. AUX jack
Caution!
- Make sure to connect the color coded leads according to the diagram. Incorrect
connections may cause the unit to malfunction or damage the vehicle’s electrical system.
- Make sure to connect the speaker (-) leads to the speaker (-) terminal. Never connect
the left and right channel speaker cables each other or to the vehicle body.
- Make sure all the connections are completely correct before turning on your unit.
Turn on/off the unit
Press button to turn on the unit. Press and hold this button again to turn off the unit.
Selecting the mode
When the unit is on, press MODE button repeatedly to select different source mode:
TUNER USB CARD BT AUX
Note: USB, CARD mode can not be selected if no such source was plugged in the unit.
Current time display
Press VOL button to display the current time when unit is ON.
Adjust time:
1. When the unit is ON. Press and hold VOL to enter into setting mode.
2. Rotate Volume knob anti-clockwise or clockwise to adjust the hour and minute value.
It will conrm your setting if no key is pressed for 5 seconds.
Reset the unit
Operating the unit for the rst time or after replacing the car battery, you must reset the
unit. To set the unit to initial status, press RES button on the front panel with a pointed
object. When some errors occur in display, you can also reset the unit, but it will erase
the clock setting and some memorized functions.
1. Insert the mounting sleeve to the car. Bend the claws outward for a tight t, if necessary.
2. Combine mounting blot, steel bar, spring washer and Hex nut. Then combine the unit
and dashboard with screw and plain washer.
Selecting band
In tuner mode, repeatedly press BAND button to select bands in following order:
FM1 FM2 FM3.
Manual / automatic tuning
- Manual Search
Choose your radio station with or .
- Automatic search
Press and hold for few seconds or . The automatic search locates strong stations.
A station with a weak signal can be set manually by repeatedly pressing or .
NOTE: During the search operation, the sound level is automatically muted.
Scanning and memorizing stations
- By BAND button (AMS)
In tuner mode, press and hold BAND button for 3 seconds to start scanning for stations
and store them automatically in memory. All preset stations are scrolled during few
seconds under your selected band. To remain on a station, press again the BAND button.
- By number button 1- 6
1. Tune to a station by or button.
2. Press and hold one of the 1- 6 number buttons for 2 seconds until LCD shows the
corresponding number, which indicates that station is stored in the corresponding
number button.
3. Under radio mode, press 1- 6 Number buttons to listen to stored stations.
4. When you are listening to a station stored on a number button, press and hold another
number button for more than 2 seconds to store the station on this number button.
Note: The unit can be stored up to 6 stations for each band.
RDS (Radio Data System)
This unit has a built-in RDS decoder system that supports broadcast stations transmitting
RDS data. This system can automatically switch to the broadcast station with the best
reception as you move on long distances (AF switching). Also if a trafc announcement
(TA) or programme type (PTY) is broadcast from a RDS station, no matter what mode
you are in. this broadcast is received.
Press and hold SEL/PTY knob, the unit will enter setting menu. Shortly press SEL/
PTY knob to choose your desire item. Rotate SEL/PTY knob to choose corresponding
setting desired.
- Alternative frequency (AF)
When the AF switching mode is selected, the radio scans the signal strength of alternative
frequencies. A new AF is stronger than the current station, it switches over to that frequency
for very short time, and the new frequency is displayed for 1-2 second. (When AF ashes
on LCD, it will search for the stronger RDS station.)
Segment off: AF switching mode off.
Segment on: AF switching mode on, and receive RDS information.
Segment ashing: AF switching mode on, but RDS information is not received yet.
Volume adjusting:
To increase or decrease the sound level, rotate VOL knob clockwise or anti-clockwise.
Using SEL/volume knob to select sound feature
Repeatedly press SEL/volume knob
To select the desired mode for sound setting in the following order: “BAS” (BASS)
“TRE” (Treble) “BAL” (Balance) “FAD” (Fader).
After selecting the desired mode, you can adjust the level by rotating the volume knob.
Preset equalizer (EQ)
When you are listening to pop music, classic music or rock music, use the equalizer to
adjust the sound quality. Press EQ button repeatedly to select different equalizer mode
in following order: FLAT CLASSIC ROCK POP EQ off.
Loudness on /off
Press and hold LOUD button until “LOUD ON” shows on display to activate LOUDNESS
function. Press and hold this button again until “LOUD OFF” to cancel LOUDNESS
function.
M-199 BT
CAR RADIO WITH BLUETOOTH & USB/SD
USER MANUAL
Please read the instruction carefully before operating the unit.
AR-3736 IB MUSE 001 REV1 GB.indd 1 2015/11/12 13:41:27
Joignez-vous à la conversation sur ce produit
Ici, vous pouvez partager ce que vous pensez du Muse M-199 BT Autoradio. Si vous avez une question, lisez d’abord attentivement le mode d’emploi. La demande d’un mode d’emploi peut être effectuée en utilisant notre formulaire de contact.