Mode d’emploi Philips GC1010 Fer à repasser

Mode d’emploi

ENGLISH

General description

.

A Spray nozzle (GC1121/1120/1115/1015)

B Filling opening

C Spray button T (GC1121/1120/1115/1015)

D Steam control

- O = no steam

- q = moderate steam

- w = maximum steam

- x = Calc-Clean function

E Extra-steam function (press steam control) (GC1121/1120)

F Temperature dial

G Temperature light

H Cord

I Type plate

J Water tank

Important

.

Read these instructions for use carefully before using the appliance and

save them for future reference.

◗ Check if the voltage indicated on the type plate corresponds to the

local mains voltage before you connect the appliance.

◗ Only connect the appliance to an earthed wall socket.

◗ Do not use the appliance if the plug, the cord or the appliance itself

shows visible damage, or if the appliance has been dropped or is

leaking.

◗ Check the cord regularly for possible damage.

◗ If the mains cord is damaged, always have it replaced by one of the

original type in order to avoid a hazard.

◗ Never leave the appliance unattended when it is connected to the

mains.

◗ Never immerse the iron and the stand, if provided, in water.

◗ Keep the appliance out of the reach of children.

◗ The soleplate of the iron can become extremely hot and may cause

burns if touched.

◗ Do not allow the cord to come into contact with the soleplate when

it is hot.

◗ When you have finished ironing, when you clean the appliance, when

you fill or empty the water tank and also when you leave the iron

even for a short while: set the steam control to position O, put the

iron on its heel and remove the mains plug from the wall socket.

◗ Always place and use the iron and the stand, if provided, on a stable,

level and horizontal surface.

◗ Do not put perfume, vinegar, starch, descaling agents, ironing aids or

other chemicals in the water tank.

◗ This appliance is intended for household use only.

Before first use

.

1 Remove any sticker or protective foil from the soleplate.

2 Let the iron heat up to maximum temperature and pass the iron

over a piece of damp cloth for several minutes to remove any

residues from the soleplate.

B

The iron may give off some smoke when you use it for the first time. This

will cease after a short while.

Preparing for use

.

Filling the water tank

Never immerse the iron in water.

1 Make sure the appliance is unplugged.

2 Set the steam control to position O (= no steam) (fig. 1).

3 Tilt the iron backwards.

4 Fill the water tank with tap water up to the maximum level (fig. 2).

Do not fill the water tank beyond the MAX indication.

◗ If the tap water in your area is very hard, we advise you to mix it

with an equal amount of distilled water or to use distilled water

only.

Setting the temperature

1 Put the iron on its heel.

2 Set the required ironing temperature by turning the temperature dial

to the appropriate position (fig. 3).

Check the laundry care label for the required ironing temperature:

1 Synthetic fabrics (e.g. acrylic, viscose, polyamide, polyester)

1 Silk

2 Wool

3 Cotton, linen

If you do not know what kind or kinds of fabic an article is made of, deter-

mine the right ironing temperature by ironing a part that will not be visible

when you wear or use the article.

Silk, woollen and synthetic materials; iron the reverse side of the fabric to

prevent shiny patches. Avoid using the spray function to prevent stains.

Start ironing the articles that require the lowest ironing temperature, such

as those made of synthetic fibers.

3 Put the mains plug in an earthed wall socket.

4 When the temperature light has gone out, wait a while before you

start ironing (fig. 4).

The temperature light will go on from time to time during ironing.

Using the appliance

.

Steam ironing

1 Make sure that there is enough water in the water tank.

2 Select the recommended ironing temperature (see chapter

'Preparing for use', section 'Setting the temperature').

3 After the temperature light has gone out, set the steam control to

the appropriate steam position. Make sure that the steam setting

you select is suitable for the ironing temperature selected: (fig. 5).

q for moderate steam (temperature settings 2 to 3)

w for maximum steam (temperature settings 3 to MAX)

The iron will start steaming as soon as the set temperature has been

reached.

Ironing without steam

1 Set the steam control to position O (= no steam).

2 Select the recommended ironing temperature (see chapter

'Preparing for use', section 'Setting the temperature').

Features

.

Spray function (GC1121/1120/1115/1015 only)

You can use the spray function to remove stubborn creases at any temper-

ature.

1 Make sure that there is enough water in the water tank.

2 Press the spray button several times to moisten the article to be

ironed (fig. 6).

Extra steam (GC1121/1120 only)

This function provides extra steam to remove very stubborn creases.

◗ The extra-steam function only works at temperature settings

between 3 and MAX.

1 Set the steam control to position w (= maximum steam) (fig. 7).

2 Press and hold the steam control for a maximum of 5 seconds

(fig. 8).

3 Release the steam control and wait at least 1 minute before using

this function again to prevent water from dripping out of the sole-

plate.

Cleaning and maintenance

.

After ironing

1 Remove the mains plug from the wall socket and let the iron cool

down.

Comfort

4239 000 52292

2/12

Évaluation

En savoir plus sur ce mode d’emploi

Nous comprenons qu’il est agréable d’avoir un mode d’emploi papier pour vos Philips GC1010 Fer à repasser. Vous pouvez toujours télécharger le mode d’emploi depuis notre site Web et l’imprimer vous-même. Si vous souhaitez disposer d’un mode d’emploi original, nous vous recommandons de contacter Philips. Ils pourront peut-être fournir un mode d’emploi original. Recherchez-vous le mode d’emploi de votre Philips GC1010 Fer à repasser dans une autre langue ? Choisissez votre langue préférée sur notre page d’accueil et recherchez le numéro de modèle pour voir si nous l’avons disponible.

Caractéristiques

Tous les modes d’emploi pour Philips Fers à repasser
Plus de modes d’emploi de Fers à repasser

Foire aux questions sur Philips GC1010 Fer à repasser

Notre équipe d’assistance recherche des informations utiles sur les produits et des réponses aux questions fréquemment posées. Si vous trouvez une inexactitude dans notre foire aux questions, veuillez nous le faire savoir en utilisant notre formulaire de contact.

Produits connexes

Mode d’emploi

Philips HI5918 Fer à repasser

Mode d’emploi

Philips GC8225 Fer à repasser

Mode d’emploi

Philips GC8420 Fer à repasser

Mode d’emploi

Philips GC7933 Fer à repasser

Mode d’emploi

Philips GC9324 Fer à repasser

Mode d’emploi

Philips GC7320 Fer à repasser

Mode d’emploi

Philips GC7011 Fer à repasser

Mode d’emploi

Philips GC9241 Fer à repasser

Catégories associées