Mode d’emploi Pioneer AVH-X8800BT Autoradio

Mode d’emploi

2

Rear panel (main terminals)

9

8

7

1

432

6

5

1 This product

2 Fuse (10 A)

3 Power supply

4 Wired remote input

Hard-wired remote control adapter can be connected (sold

separately).

5

Aerial jack

6 Vehicle Bus conversion cable 15.8 cm

Please refer to the instruction manual for the Vehicle Bus

adapter (sold separately).

7

Microphone 3 m

8 RGB cable (supplied with Navigation system)

9 Pioneer navigation system

Please contact your dealer to inquire about the connectable

navigation unit.

Precautions

Your new product and this manual

 Do not operate this product, any applications, or the rear

view camera option (if purchased) if doing so will divert your

attention in any way from the safe operation of your vehicle.

Always observe safe driving rules and follow all existing

traffic regulations. If you experience difficulty in operating

this product or reading the display, park your vehicle in a

safe location and apply the handbrake before making the

necessary adjustments.



Do not install this product where it may

(i) obstruct the driver’s vision,

(ii) impair the performance of any of the vehicle’s operating

systems of safety features, including airbags, hazard lamp

buttons, or

(iii) impair the driver’s ability to safely operate the vehicle.

In some cases, it may not be possible to install this product

because of the vehicle type or the shape of the vehicle

interior.



The graphical symbol placed on the product means

direct current.

Important safeguards

CAUTION

Pioneer does not recommend that you install this

product yourself. This product is designed for

professional installation only. We recommend that only

authorised Pioneer service personnel, who have special

training and experience in mobile electronics, set up and

install this product. NEVER SERVICE THIS PRODUCT

YOURSELF. Installing or servicing this product and its

connecting cables may expose you to the risk of electric

shock or other hazards, and can cause damage to this

product that is not covered by warranty.

Precautions before connecting

the system

WARNING

Do not take any steps to tamper with or disable the

handbrake interlock system which is in place for your

protection. Tampering with or disabling the handbrake

interlock system could result in serious injury or death.

CAUTION

 Secure all wiring with cable clamps or electrical tape.

Do not allow any bare wiring to remain exposed.



Do not directly connect the yellow lead of this product

to the vehicle battery. If the lead is directly connected

to the battery, engine vibration may eventually cause

the insulation to fail at the point where the wire

passes from the passenger compartment into the

engine compartment. If the yellow lead’s insulation

tears as a result of contact with metal parts, short-

circuiting can occur, resulting in considerable danger.



It is extremely dangerous to allow cables to become

wound around the steering column or gearstick. Be

sure to install this product, its cables, and wiring

away in such so that they will not obstruct or hinder

driving.



Make sure that the cables and wires will not interfere

with or become caught in any of the vehicle’s moving

parts, especially the steering wheel, gearstick,

handbrake, sliding seat tracks, doors, or any of the

vehicle’s controls.



Do not route wires where they will be exposed to

high temperatures. If the insulation heats up, wires

may become damaged, resulting in a short circuit or

malfunction and permanent damage to the product.



Do not shorten any leads. If you do, the protection

circuit (fuse holder, fuse resistor or filter, etc.) may

fail to work properly.



Never feed power to other electronic products by

cutting the insulation of the power supply lead of

this product and tapping into the lead. The current

capacity of the lead will be exceeded, causing

overheating.

Before installing this product

 Use this product with a 12-volt battery and negative ground-

ing only. Failure to do so may result in a fire or malfunction.



To avoid shorts in the electrical system, be sure to discon-

nect the (–) battery cable before installation.

To prevent damage

WARNING

 Use speakers over 50 W (maximum input power) and

between 4 Ω to 8 Ω (impedance value). Do not use 1 Ω

to 3 Ω speakers for this product.

 The black lead is earth. Please earth this lead separately

from the earth of high-current products such as power

amps. Do not earth more than one product together with

the earth from another product. For example, you must

separately earth any amp unit away from the earth of this

product. Connecting grounds together can cause a fire

and/or damage the products if their grounds became

detached.



When replacing the fuse, be sure to only use a fuse of

the rating prescribed on this product.



This product cannot be installed in a vehicle without ACC

(accessory) position on the ignition switch.

A

C

C

O

N

S

T

A

R

T

O

F

F

O

N

S

T

A

R

T

O

F

F

ACC position No ACC position



To avoid short-circuiting, cover the disconnected lead with

insulating tape. It is especially important to insulate all

unused speaker leads, which if left uncovered may cause a

short circuit.



For connecting a power amp or other devices to this product,

refer to the manual for the product to be connected.

Notice for the blue/white lead

When the ignition switch is turned on (ACC ON), a control signal

is output through the blue/white lead. Connect to an external

power amp’s system remote control terminal, the auto-aerial

relay control terminal, or the aerial booster power control termi-

nal (max. 300 mA 12 V DC). The control signal is output through

the blue/white lead, even if the audio source is switched off.

Important

When this product is in “Power OFF” mode, the control signal

is also turned off. If “Power OFF” mode is cancelled, the

control signal is output again and the aerial is extended with

the auto aerial function (if the aerial is being used). Be careful

so that the extended aerial does not come into contact with

any obstacles.

Connection

2 < CRD4940-A >< CRD4940-A >

Connection Connection

Évaluation

En savoir plus sur ce mode d’emploi

Nous comprenons qu’il est agréable d’avoir un mode d’emploi papier pour vos Pioneer AVH-X8800BT Autoradio. Vous pouvez toujours télécharger le mode d’emploi depuis notre site Web et l’imprimer vous-même. Si vous souhaitez disposer d’un mode d’emploi original, nous vous recommandons de contacter Pioneer. Ils pourront peut-être fournir un mode d’emploi original. Recherchez-vous le mode d’emploi de votre Pioneer AVH-X8800BT Autoradio dans une autre langue ? Choisissez votre langue préférée sur notre page d’accueil et recherchez le numéro de modèle pour voir si nous l’avons disponible.

Caractéristiques

Tous les modes d’emploi pour Pioneer Autoradios
Plus de modes d’emploi de Autoradios

Foire aux questions sur Pioneer AVH-X8800BT Autoradio

Notre équipe d’assistance recherche des informations utiles sur les produits et des réponses aux questions fréquemment posées. Si vous trouvez une inexactitude dans notre foire aux questions, veuillez nous le faire savoir en utilisant notre formulaire de contact.

Produits connexes

Mode d’emploi

Pioneer DEH-P9100R Autoradio

Mode d’emploi

Pioneer DEH-915RDS Autoradio

Mode d’emploi

Pioneer MVH-280DAB Autoradio

Mode d’emploi

Pioneer DEH-X7800DAB Autoradio

Mode d’emploi

Pioneer DEH-S320BT Autoradio

Mode d’emploi

Pioneer DEH-S42BT Autoradio

Mode d’emploi

Pioneer DEH-2600UI Autoradio

Mode d’emploi

Pioneer DEH-1600UBG Autoradio

Catégories associées