Mode d’emploi Renkforce 1207926 Dual SD Lecteur de cartes

Mode d’emploi

Inserting/Removing the Memory Card

Important! In order to use SDXC memory cards with Windows XP, an update

of Windows XP is required. Only then will the „exFat“ file system of SDXC

memory cards be supported. You can download the update at www.micro-

soft.com. To find the update, e.g. enter the search terms „exfat windows xp“

in the search bar of your internet browser. In Windows Vista, you have to

install the service pack 1 to enable the card reader to support SDXC cards.

Insert a memory card into the appropriate slot in the card reader (as printed on the

card reader). Pay attention to the correct orientation when inserting the memory card;

do not use force!

If you wish to remove the memory card from the card reader (or to disconnect the

card reader from the computer), wait until all read/write accesses to the memory card

are completed. Only then you should remove the memory card from the card reader.

If the memory card is removed during a read/write access (or the card

reader disconnected from the computer), the data on the memory card can

be damaged. The memory card may possibly even require subsequent re-

formatting.

Reading/Writing to Memory Cards

A memory card inserted into the card reader will be integrated in the same way as a

conventional removable media drive. With the Windows File Manager you can now

read the data on the memory card (or store data on the memory card) in the same way

as you use a USB hard drive or a USB stick.

The maximum speed attainable when reading / writing a memory card depends on

your memory card. Therefore, with slower memory cards or while writing onto the

memory card it is normal that the data transfer rate does not increase if you use the

card reader on a USB3.0 port instead of a conventional USB2.0 port.

Disposal

Electronic devices are recyclable waste and must not be disposed of in the

household waste.

At the end of its service life, dispose of the product according to the relevant

statutory regulations.

G

Operating Instructions

Dual SD Card Reader USB 3.0

Item no. 1207926

Intended use

The product can be plugged into a computer’s USB port and it is designed for reading

and writing to appropriate memory cards. All names of companies and products are

the trademarks of the respective owners. All rights reserved.

For safety and approval purposes (CE), you must not rebuild and/or modify this product.

If you use the product for purposes other than those described above, the product may

be damaged. In addition, improper use can cause hazards such as short circuiting,

fire, electric shock etc. Read the instructions carefully and keep them. Make this prod-

uct available to third parties only together with its operating instructions.

Delivery content

• Card reader

• Operating instructions

Safety instructions

Read the operating instructions carefully and especially observe the safety

information. If you do not follow the safety instructions and information on

proper handling in this manual, we assume no liability for any resulting

personal injury or damage to property. Such cases will invalidate the war-

ranty/guarantee.

Persons / Product

• The product is not a toy. Keep it out of the reach of children and pets.

• Protect the product from extreme temperatures, direct sunlight, strong jolts, high

humidity, moisture, flammable gases, vapours and solvents.

• Handle the product carefully. Jolts, impacts or a fall even from a low height can

damage the product.

• Also observe the safety and operating instructions of any other devices which are

connected to the product.

Miscellaneous

• Consult an expert when in doubt about operation, safety or connection of the de-

vice.

• Maintenance, modifications and repairs are to be performed exclusively by an ex-

pert or at a qualified shop.

• If you have questions which remain unanswered by these operating instructions,

contact our technical support service or other technical personnel.

Connection

Switch on your computer and wait until the operating system has booted completely.

Connect the card reader to a free USB3.0 port on your computer. During the initial

connection, Windows recognises the new hardware; the drivers are already included

in Windows. The card reader can also be connected to a USB2.0/1.1 port, if your com-

puter does not yet have a USB3.0 port. However, this does not result in faster data

transmission.

This is a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com).

All rights including translation reserved. Reproduction by any method, e.g. photocopy, microfilming, or the capture in electronic data

processing systems require the prior written approval by the editor. Reprinting, also in part, is prohibited. This publication represent

the technical status at the time of printing.

© Copyright 2014 by Conrad Electronic SE.

Évaluation

En savoir plus sur ce mode d’emploi

Nous comprenons qu’il est agréable d’avoir un mode d’emploi papier pour vos Renkforce 1207926 Dual SD Lecteur de cartes. Vous pouvez toujours télécharger le mode d’emploi depuis notre site Web et l’imprimer vous-même. Si vous souhaitez disposer d’un mode d’emploi original, nous vous recommandons de contacter Renkforce. Ils pourront peut-être fournir un mode d’emploi original. Recherchez-vous le mode d’emploi de votre Renkforce 1207926 Dual SD Lecteur de cartes dans une autre langue ? Choisissez votre langue préférée sur notre page d’accueil et recherchez le numéro de modèle pour voir si nous l’avons disponible.

Caractéristiques

Tous les modes d’emploi pour Renkforce Lecteurs de cartes
Plus de modes d’emploi de Lecteurs de cartes

Foire aux questions sur Renkforce 1207926 Dual SD Lecteur de cartes

Notre équipe d’assistance recherche des informations utiles sur les produits et des réponses aux questions fréquemment posées. Si vous trouvez une inexactitude dans notre foire aux questions, veuillez nous le faire savoir en utilisant notre formulaire de contact.

Produits connexes

Mode d’emploi

Renkforce 809339 All in One Lecteur de cartes

Mode d’emploi

Renkforce 1095095 CR09E Lecteur de cartes

Mode d’emploi

Renkforce 1198497 USB 2.0 Lecteur de cartes

Mode d’emploi

Renkforce 1507156 USB 2.0 Lecteur de cartes

Mode d’emploi

Renkforce 1218046 CR25E Lecteur de cartes

Mode d’emploi

Renkforce 1095094 USB 2.0 Lecteur de cartes

Mode d’emploi

Renkforce 1095091 Stick 3.0 Lecteur de cartes

Mode d’emploi

Lexar Mediamove Lecteur de cartes

Catégories associées