Mode d’emploi RIDGID R41422 Tronçonneuse à métaux

Mode d’emploi

2 - English

GENERAL SAFETY RULES

WARNING:

Read and understand all instructions. Failure

to follow all instructions listed below, may result in

electric shock, fire and/or serious personal injury.

READ ALL INSTRUCTIONS

 KNOW YOUR POWER TOOL. Read the operator’s

manual carefully. Learn the applications and limitations

as well as the specific potential hazards related to this

tool.

 GUARD AGAINST ELECTRICAL SHOCK BY

PREVENTING BODY CONTACT WITH GROUNDED

SURFACES. For example: pipes, radiators, ranges,

refrigerator enclosures.

 KEEP GUARDS IN PLACE and in good working order.

 REMOVE ADJUSTING KEYS AND WRENCHES. Form

habit of checking to see that keys and adjusting wrenches

are removed from tool before turning it on.

 KEEP WORK AREA CLEAN. Cluttered areas and

benches invite accidents. DO NOT leave tools or pieces

of wood on the tool while it is in operation.

 DO NOT USE IN DANGEROUS ENVIRONMENTS. Do

not use power tools in damp or wet locations or expose

to rain. Keep the work area well lit.

 KEEP CHILDREN AND VISITORS AWAY. All visitors

should wear safety glasses and be kept a safe distance

from work area. Do not let visitors contact tool or extension

cord while operating.

 MAKE WORKSHOP CHILDPROOF with padlocks,

master switches, or by removing starter keys.

 DON’T FORCE THE TOOL. It will do the job better and

safer at the feed rate for which it was designed.

 USE THE RIGHT TOOL. Do not force the tool or

attachment to do a job for which it was not designed.

 USE THE PROPER EXTENSION CORD. Make sure

your extension cord is in good condition. Use only a

cord heavy enough to carry the current your product

will draw. An undersized cord will cause a drop in line

voltage resulting in loss of power and overheating. A wire

gauge size (A.W.G.) of at least 14 is recommended for an

extension cord 25 feet or less in length. If in doubt, use

the next heavier gauge. The smaller the gauge number,

the heavier the cord.





DRESS PROPERLY. Do not wear loose clothing, gloves,

neckties, or jewelry. They can get caught and draw you

into moving parts. Also wear protective hair covering to

contain long hair.

 ALWAYS WEAR EYE PROTECTION WITH SIDE

SHIELDS WHICH IS MARKED TO COMPLY WITH

ANSI Z87.1 WHEN USING THIS PRODUCT.

 SECURE WORK. Use clamps or a vise to hold work when

practical, it is safer than using your hand and frees both

hands to operate the tool.

 DO NOT OVERREACH. Keep proper footing and balance

at all times.

 MAINTAIN TOOLS WITH CARE. Keep tools sharp

and clean for better and safer performance. Follow

instructions for lubricating and changing accessories.

 DISCONNECT TOOLS. When not in use, before servicing,

or when changing attachments, wheels, bits, cutters, etc.

All tools should be disconnected from power source.

 AVOID ACCIDENTAL STARTING. Be sure switch is off

when plugging in any tool.

 USE RECOMMENDED ACCESSORIES. Consult the

operator’s manual for recommended accessories. The

use of improper accessories may result in injury.

 NEVER STAND ON TOOL. Serious injury could occur

if the tool is tipped.

 CHECK DAMAGED PARTS. Before further use of the

tool, a guard or other part that is damaged should be

carefully checked to determine that it will operate properly

and perform its intended function. Check for alignment

of moving parts, binding of moving parts, breakage of

parts, mounting and any other conditions that may affect

its operation. A guard or other part that is damaged must

be properly repaired or replaced by an authorized service

center to avoid risk of personal injury.

 NEVER LEAVE TOOL RUNNING UNATTENDED. TURN

THE POWER OFF. Don't leave tool until it comes to a

complete stop.

 PROTECT YOUR LUNGS. Wear a face or dust mask if

the cutting operation is dusty.

 PROTECT YOUR HEARING. Wear hearing protection

during extended periods of operation.

 DO NOT ABUSE CORD. Never carry tool by the cord or

yank it to disconnect from receptacle. Keep cord from

heat, oil, and sharp edges.

 USE OUTDOOR EXTENSION CORDS. When tool is

used outdoors, use only extension cords with approved

ground connection that are intended for use outdoors

and so marked.

WHEEL COASTS AFTER BEING TURNED OFF.

 NEVER USE IN AN EXPLOSIVE ATMOSPHERE. Normal

sparking of the motor could ignite fumes.

Évaluation

En savoir plus sur ce mode d’emploi

Nous comprenons qu’il est agréable d’avoir un mode d’emploi papier pour vos RIDGID R41422 Tronçonneuse à métaux. Vous pouvez toujours télécharger le mode d’emploi depuis notre site Web et l’imprimer vous-même. Si vous souhaitez disposer d’un mode d’emploi original, nous vous recommandons de contacter RIDGID. Ils pourront peut-être fournir un mode d’emploi original. Recherchez-vous le mode d’emploi de votre RIDGID R41422 Tronçonneuse à métaux dans une autre langue ? Choisissez votre langue préférée sur notre page d’accueil et recherchez le numéro de modèle pour voir si nous l’avons disponible.

Caractéristiques

Tous les modes d’emploi pour RIDGID Tronçonneuses à métaux
Plus de modes d’emploi de Tronçonneuses à métaux

Foire aux questions sur RIDGID R41422 Tronçonneuse à métaux

Notre équipe d’assistance recherche des informations utiles sur les produits et des réponses aux questions fréquemment posées. Si vous trouvez une inexactitude dans notre foire aux questions, veuillez nous le faire savoir en utilisant notre formulaire de contact.

Produits connexes

Mode d’emploi

Bosch GCO 200 Tronçonneuse à métaux

Mode d’emploi

Scheppach MT355s Tronçonneuse à métaux

Mode d’emploi

Evolution EVO355 Raptor Tronçonneuse à métaux

Mode d’emploi

Peugeot EnergyCut-180MC Tronçonneuse à métaux

Mode d’emploi

Kity MTC355 Tronçonneuse à métaux

Mode d’emploi

DeWalt D28730 Tronçonneuse à métaux

Mode d’emploi

Bosch GCO 240 Tronçonneuse à métaux

Mode d’emploi

Einhell TC-MC 355/1 Tronçonneuse à métaux

Catégories associées