Mode d’emploi Rosières RSHD 90 IN Hotte aspirante

Mode d’emploi

ENGLISH

DESCRIPTION

The hood may be in the filtering or the ducting version.

Filtering version (Fig. 1A or 1B): The hood aspirates the kitchen air saturated with fumes and odours, purifies it through

the grease filters and charcoal filter and returns clean air into the room. For constant efficiency, the charcoal filter must

be replaced periodically. The charcoal filter is not supplied.

Ducting version (Fig. 2): The hood aspirates the kitchen air saturated with fumes and odours, passes it through the

grease filters and expels it to the outside through an outlet pipe. With this version the charcoal filter is not required. Decide

from the outset on the type of installation (filtering or ducting). For greater efficiency, we recommend you install the hood

in the ducting version (if possible).

INSTALLATION

ATTENTION: Two persons are required for proper installation; the unit should be installed by a qualified

operator. Remove the grease filters before proceeding with the assembly instructions. This will make the appliance easier

to handle.

1. Removal of grease filters: Fig. 3: push the stop towards the rear of the appliance and turn the filter outwards.

INSTALLATION IN DUCTING VERSION: Before fixing, the outlet pipe for air evacuation to the outside must be

installed. Use an outlet pipe with: – minimum indispensable length; – minimum possible bends (maximum angle of bend:

90°); – certified material (according to the State); – an as smooth as possible inside. It is also advisable to avoid any

drastic changes in pipe cross-section (recommended diameter: 150 mm). For air evacuation to the outside, follow all the

other instructions given on the “Warnings” sheet. Prepare the power supply within the telescopic chimney (for the electrical

connection, follow all the other instructions on the “Warnings” sheet).

2. Fixing to the wall: Draw a line on the wall in vertical line with your hob. Mark the first 2 holes to be drilled in

the wall, respecting the distances indicated in Fig. 4. Drill the 2 holes and fit the screw anchors provided. As already specified

on the “Warnings” sheet, bear in mind that the distance between the lower edge of the hood and the hob must be min.

650 mm. Fix the metal bracket (A) to the wall using the 2 holes just drilled (Fig. 5); the screws for fixing the bracket are

provided. Use the 2 cut-out triangles on the bracket to position it exactly along the vertical axis of the hood. Hang the

hood on the bracket (Fig. 6). Adjust the horizontal position moving the hood to the right or left so that it is aligned with

the wall units. If you also need to adjust the hood in height, operate on the adjusting screws (B) provided. When adjustment

has been completed, without removing the hood, mark the other 4 holes to be drilled (C) in the wall. Remove the hood

and drill the holes marked (8 mm diameter). Then use the 4 screw anchors and the 4 screws provided for final fixing.

3. Flange assembly: set the flange (E) over the motor and press slightly (Fig. 7).

4. Mount the plate of the electrical system fixing it with 3 screws (Fig. 7V).

5. Fixing the telescopic flues:

5a - Adjust the width of the support bracket (D) of the telescopic flue by means of the screws (E) as shown in Fig.8; then,

by means of the screw anchors and screws (F) provided, fix the bracket to the ceiling in such a way that it is positioned

along the axis with your hood.

5b - Connect the air outlet pipe to the air vent of the hood. - Use a flexible pipe and lock it to the air vent of the hood

with a metal hose clamp - Fig. 9 (pipe and clamp are not provided). - For exhaust hoods, turn the upper flue over so that

the air exhaust grid is in the lower section (Fig. 10).

5c - Plug in the hood. Insert the extension flues setting them on the hood; extend the upper flue to the ceiling and secure

with the 2 screws (H) - Fig. 11.

INSTALLATION IN FILTERING VERSION: Prepare the power supply within the telescopic flues (for the electrical

connection, follow all the other instructions on the “Warnings” sheet).

Fixing to the wall: for fixing to the wall refer to the instructions for the ducting version (see points 2, 3, and 4), then

continue with the instructions below.

Fixing the telescopic flues: - Adjust the width of the support bracket (D) of the telescopic flue by means of the

screws (E) as shown in Fig. 8. - Then, by means of the screw anchors and screws (F) provided, fix the bracket to the

ceiling in such a way that it is positioned along the axis with your hood. - Mount the flange on the hood in correspondence

to the air outlet point (Fig. 12). – Take the air baffle and fit a flexible pipe to it (125 mm diameter) locking it with a metal

hose clamp (pipe and clamps are not provided). Fit the air baffle to the upper flue (Fig. 13) with 4 screws.

- Connect the flexible pipe to the flange on the air vent (Fig. 14). - Plug in the hood. Insert the extension flues setting

them on the hood; extend the upper flue to the ceiling and secure with the 2 screws H (Fig. 11). - Install the charcoal

filter fitting the two filter clips in their housings (Fig. 15) and turning the filter upward.

Évaluation

En savoir plus sur ce mode d’emploi

Nous comprenons qu’il est agréable d’avoir un mode d’emploi papier pour vos Rosières RSHD 90 IN Hotte aspirante. Vous pouvez toujours télécharger le mode d’emploi depuis notre site Web et l’imprimer vous-même. Si vous souhaitez disposer d’un mode d’emploi original, nous vous recommandons de contacter Rosieres. Ils pourront peut-être fournir un mode d’emploi original. Recherchez-vous le mode d’emploi de votre Rosières RSHD 90 IN Hotte aspirante dans une autre langue ? Choisissez votre langue préférée sur notre page d’accueil et recherchez le numéro de modèle pour voir si nous l’avons disponible.

Caractéristiques

Tous les modes d’emploi pour Rosières Hottes aspirantes
Plus de modes d’emploi de Hottes aspirantes

Foire aux questions sur Rosières RSHD 90 IN Hotte aspirante

Notre équipe d’assistance recherche des informations utiles sur les produits et des réponses aux questions fréquemment posées. Si vous trouvez une inexactitude dans notre foire aux questions, veuillez nous le faire savoir en utilisant notre formulaire de contact.

Produits connexes

Mode d’emploi

Rosières RDM 61 IN Hotte aspirante

Mode d’emploi

Rosières RHT 650 IN Hotte aspirante

Mode d’emploi

Rosières RDR 91 AV Hotte aspirante

Mode d’emploi

Rosières RHC 638 PN Hotte aspirante

Mode d’emploi

Rosières RHG 527 GR Hotte aspirante

Mode d’emploi

Rosières RHG 529 IN Hotte aspirante

Mode d’emploi

Rosières RDR 61 AV Hotte aspirante

Mode d’emploi

Rosières RDR 91 BMV Hotte aspirante

Catégories associées