Mode d’emploi Ryobi RMS18254X-0 Scie à onglet

Mode d’emploi

■ Maintain power tools and accessories. Check for

misalignment or binding of moving parts, breakage

of parts and any other condition that may affect the

power tool’s operation. If damaged, have the power

tool repaired before use. Many accidents are caused

by poorly maintained power tools.

■ Keep cutting tools sharp and clean. Properly

maintained cutting tools with sharp cutting edges are

less likely to bind and are easier to control.

■ Use the power tool, accessories and tool bits etc.

in accordance with these instructions, taking into

account the working conditions and the work to

be performed. Use of the power tool for operations

different from those intended could result in a hazardous

situation.

■ Keep handles and grasping surfaces dry, clean

and free from oil and grease. Slippery handles and

grasping surfaces do not allow for safe handling and

control of the tool in unexpected situations.

BATTERY TOOL USE AND CARE

■ Recharge only with the charger specified by the

manufacturer. A charger that is suitable for one type

of battery pack may create a risk of fire when used with

another battery pack.

■ Use power tools only with specifically designated

battery packs. Use of any other battery packs may

create a risk of injury and fire.

■ When battery pack is not in use, keep it away from

other metal objects, like paper clips, coins, keys,

nails, screws or other small metal objects, that can

make a connection from one terminal to another.

Shorting the battery terminals together may cause burns

or a fire.

■ Under abusive conditions, liquid may be ejected from

the battery; avoid contact. If contact accidentally

occurs, flush with water. If liquid contacts eyes,

additionally seek medical help. Liquid ejected from

the battery may cause irritation or burns.

■ Do not use a battery pack or tool that is damaged or

modified. Damaged or modified batteries may exhibit

unpredictable behaviour resulting in fire, explosion or

risk of injury.

■ Do not expose a battery pack or tool to fire or

excessive temperature. Exposure to fire or temperature

above 130°C may cause explosion.

■ Follow all charging instructions and do not charge

the battery pack or tool outside the temperature

range specified in the instructions. Charging

improperly or at temperatures outside the specified

range may damage the battery and increase the risk of

fire.

SERVICE

■ Have your power tool serviced by a qualified repair

person using only identical replacement parts. This

will ensure that the safety of the power tool is maintained.

■ Never service damaged battery packs. Service

of battery packs should only be performed by the

manufacturer or authorized service providers.

SAFETY INSTRUCTIONS FOR MITRE SAWS

■ Mitre saws are intended to cut wood or wood-like

products, they cannot be used with abrasive cut-off

wheels for cutting ferrous material such as bars,

rods, studs, etc. Abrasive dust causes moving parts

such as the lower guard to jam. Sparks from abrasive

cutting will burn the lower guard, the kerf insert and other

plastic parts.

■ Use clamps to support the workpiece whenever

possible. If supporting the workpiece by hand, you

must always keep your hand at least 100 mm from

either side of the saw blade. Do not use this saw to

cut pieces that are too small to be securely clamped

or held by hand. If your hand is placed too close to

the saw blade, there is an increased risk of injury from

blade contact.

■ The workpiece must be stationary and clamped or

held against both the fence and the table. Do not

feed the workpiece into the blade or cut “freehand”

in any way. Unrestrained or moving workpieces could

be thrown at high speeds, causing injury.

■ Push the saw through the workpiece. Do not pull the

saw through the workpiece. To make a cut, raise the

saw head and pull it out over the workpiece without

cutting, start the motor, press the saw head down

and push the saw through the workpiece. Cutting on

the pull stroke is likely to cause the saw blade to climb

on top of the workpiece and violently throw the blade

assembly towards the operator.

■ Never cross your hand over the intended line of

cutting either in front or behind the saw blade.

Supporting the workpiece “cross handed” i.e. holding

the workpiece to the right of the saw blade with your left

hand or vice versa is very dangerous.

■ Do not reach behind the fence with either hand

closer than 100 mm from either side of the saw

blade, to remove wood scraps, or for any other

reason while the blade is spinning. The proximity of

the spinning saw blade to your hand may not be obvious

and you may be seriously injured.

■ Inspect your workpiece before cutting. If the

workpiece is bowed or warped, clamp it with the

outside bowed face toward the fence. Always make

certain that there is no gap between the workpiece,

fence and table along the line of the cut. Bent or

warped workpieces can twist or shift and may cause

binding on the spinning saw blade while cutting. There

should be no nails or foreign objects in the workpiece.

■ Do not use the saw until the table is clear of all

tools, wood scraps, etc., except for the workpiece.

Small debris or loose pieces of wood or other objects

that contact the revolving blade can be thrown with high

speed.

■ Cut only one workpiece at a time. Stacked multiple

workpieces cannot be adequately clamped or braced

and may bind on the blade or shift during cutting.

■ Ensure the mitre saw is mounted or placed on a

level, firm work surface before use. A level and firm

work surface reduces the risk of the mitre saw becoming

unstable.

■ Plan your work. Every time you change the bevel or

mitre angle setting, make sure the adjustable fence

is set correctly to support the workpiece and will

not interfere with the blade or the guarding system.

Without turning the tool “ON” and with no workpiece

on the table, move the saw blade through a complete

simulated cut to assure there will be no interference or

danger of cutting the fence.

■ Provide adequate support such as table extensions,

saw horses, etc. for a workpiece that is wider or

4

Original Instructions

Évaluation

En savoir plus sur ce mode d’emploi

Nous comprenons qu’il est agréable d’avoir un mode d’emploi papier pour vos Ryobi RMS18254X-0 Scie à onglet. Vous pouvez toujours télécharger le mode d’emploi depuis notre site Web et l’imprimer vous-même. Si vous souhaitez disposer d’un mode d’emploi original, nous vous recommandons de contacter Ryobi. Ils pourront peut-être fournir un mode d’emploi original. Recherchez-vous le mode d’emploi de votre Ryobi RMS18254X-0 Scie à onglet dans une autre langue ? Choisissez votre langue préférée sur notre page d’accueil et recherchez le numéro de modèle pour voir si nous l’avons disponible.

Caractéristiques

Tous les modes d’emploi pour Ryobi Scies à onglets
Plus de modes d’emploi de Scies à onglets

Foire aux questions sur Ryobi RMS18254X-0 Scie à onglet

Notre équipe d’assistance recherche des informations utiles sur les produits et des réponses aux questions fréquemment posées. Si vous trouvez une inexactitude dans notre foire aux questions, veuillez nous le faire savoir en utilisant notre formulaire de contact.

Produits connexes

Mode d’emploi

Ryobi TS230 Scie à onglet

Mode d’emploi

Ryobi TS1300 Scie à onglet

Mode d’emploi

Ryobi ETMS1825 Scie à onglet

Mode d’emploi

Ryobi TSS701 Scie à onglet

Mode d’emploi

Ryobi EMS-2025SCL Scie à onglet

Mode d’emploi

Ryobi R18MS216-0 Scie à onglet

Mode d’emploi

Ryobi TS1352 Scie à onglet

Mode d’emploi

Ryobi EMS190DC Scie à onglet

Catégories associées