Mode d’emploi Skil 2036 AA Visseuse

Mode d’emploi

INTRODUCTION

● This tool with left/right rotation is intended for

screwdriving in wood

TECHNICAL SPECIFICATIONS 1

SAFETY

● Read and save this instruction manual (pay special

attention to the safety instructions at the back) 2

● Avoid damage that can be caused by screws, nails and

other elements in your workpiece; remove them before

you start working

● Always check that the supply voltage is the same as the

voltage indicated on the nameplate of the charger

(chargers with a rating of 230V or 240V can also be

connected to a 220V supply)

● In case of electrical or mechanical malfunction,

immediately switch off the tool or unplug charger from

power source

● SKIL can assure flawless functioning of the tool only

when original accessories are used

● This tool should not be used by people under the age of

16 years

● Be careful not to drive into areas where electrical wires

may be contacted

● Do not activate switch when changing accessories or

carrying the tool

CHARGING/BATTERIES

● Charge battery only with the charger that is supplied

with the tool

● Do not expose tool and charger to rain

● Never charge battery outdoors 3

● Store tool and charger in locations where temperature

will not exceed 40°C or drop below 0°C

● Batteries will explode in fire, so do not burn battery for

any reason

● When damaged, and under extreme usage and

temperature conditions, batteries may start to leak

- if liquid comes into contact with the skin, wash quickly

with soap and water, then with lemon juice or vinegar

- if liquid gets into the eyes, flush eyes with clean water

for a minimum of 10 minutes and seek immediately

medical attention

● Do not use tool or charger when damaged; take it to one

of the officially registered SKIL Service Stations for a

safety check

● Do not disassemble charger or battery

WHEN CONNECTING NEW 3-PIN PLUG (U.K. ONLY):

● Do not connect the blue (= neutral) or brown (= live) wire

in the cord of the charger to the earth terminal of the

plug

● If for any reason the old plug is cut off the cord of the

charger, it must be disposed of safely and not left

unattended

USE

● Charging battery 4

- battery of new tools is not fully charged

! unplug the charger from the tool after charging

period has ended thereby lengthening the service

life of the battery

IMPORTANT:

- while charging, the charger and the tool may become

warm to touch; this is normal and does not indicate a

problem

- do not charge at temperatures below 0°C and over

40°C; this will seriously damage the battery as well as

the charger

-when you charge the battery for the first time, it only

accepts 80% of its maximum capacity; after several

charges and discharges, however, the batteries should

be at full capacity and deliver maximum performance

- do not repeatedly recharge the battery after only a

few minutes of operation; this may result in a

reduction of operating time and battery efficiency

- the nickel-cadmium battery must be kept separate from

the natural environment and should not be disposed of

as normal domestic waste 5 (symbol 5a will remind

you of this when the need for disposing occurs)

! prior to disposal protect battery terminals with

heavy tape to prevent short-circuit

-if you anticipate long periods of non-use for the tool,

it is best to unplug the charger from its power source

● On/Off & Changing direction of rotation 6

● Changing bits 7

- push bit to end position in bit holder

! never use bits shorter than 30 mm

! do not use bits with a damaged shank

● Automatic spindle-lock

Allows you to manually tighten or loosen screws, when

necessary 8

APPLICATION ADVICE

● Use the appropriate bits 9

! do not use damaged bits

● When turning in a screw at/near the cross cut end or an

edge of wood one should pre-drill a hole in order to

avoid cracking of the wood

● For an optimal use of the tool a steady pressure on the

screw is required, especially while removing

● When screwdriving in hard wood one should pre-drill a

hole

● For more tips see www.skileurope.com

GUARANTEE / ENVIRONMENT

● Keep tool and charger clean

- clean charging contacts of charger with alcohol or

contact cleaner

! unplug charger from power source before cleaning

● This SKIL product is guaranteed in accordance with

statutory/country-specific regulations; damage due to

normal wear and tear, overload or improper handling will

be excluded from the guarantee

GB

5

XP SKIL IB 2036.2 05-12-2003 12:14 Pagina 5

Évaluation

En savoir plus sur ce mode d’emploi

Nous comprenons qu’il est agréable d’avoir un mode d’emploi papier pour vos Skil 2036 AA Visseuse. Vous pouvez toujours télécharger le mode d’emploi depuis notre site Web et l’imprimer vous-même. Si vous souhaitez disposer d’un mode d’emploi original, nous vous recommandons de contacter Skil. Ils pourront peut-être fournir un mode d’emploi original. Recherchez-vous le mode d’emploi de votre Skil 2036 AA Visseuse dans une autre langue ? Choisissez votre langue préférée sur notre page d’accueil et recherchez le numéro de modèle pour voir si nous l’avons disponible.

Caractéristiques

Tous les modes d’emploi pour Skil Visseuses
Plus de modes d’emploi de Visseuses

Foire aux questions sur Skil 2036 AA Visseuse

Notre équipe d’assistance recherche des informations utiles sur les produits et des réponses aux questions fréquemment posées. Si vous trouvez une inexactitude dans notre foire aux questions, veuillez nous le faire savoir en utilisant notre formulaire de contact.

Produits connexes

Mode d’emploi

Skil 2710 GA Visseuse

Mode d’emploi

Skil 2636 AD Visseuse

Mode d’emploi

Skil 2714 GA Visseuse

Mode d’emploi

Skil 2636 AA Visseuse

Mode d’emploi

Skil 2705 AA Visseuse

Mode d’emploi

Skil 2436 AC Visseuse

Mode d’emploi

Skil 2348 AA Visseuse

Mode d’emploi

Skil 6940 MA Visseuse

Catégories associées