Mode d’emploi Sunbeam 3946 Steam Master Deluxe Fer à repasser

Mode d’emploi

5

4

BEFORE THE FIRST USE

• When turned on for the first time, your new iron may give off a slight odor for up

to ten minutes. This is due to the initial heating of the materials used. It is safe,

not detrimental to the performance of the product, and will not recur.

• Prior to first use, clean steam vents using the SHOT OF STEAM

®

feature.

After cleaning vents, run iron over an all-cotton cloth to remove any residue.

• When not ironing, always have steam dial turned to “0” No steam .

INSTRUCTIONS FOR USE

DRY IRONING

• Plug the cord into a 230 volt AC outlet. On units with automatic shut-off,

the auto off light will iluminate.

• Turn the temperature dial to the desired setting (refer to Ironing Guide for

recommended settings). While iron is heating, place iron on heel rest on a stable,

protected surface.

• Set the steam dial on ( ) to prevent steam flow if water is in the tank.

STEAM IRONING

• Make sure the plug is removed from the wall socket before filling the iron with water.

• Turn the steam dial to no steam icon area.

• Place the iron on its heel and open the water reservoir cover. Pour water slowly into

the water reservoir. Fill up to the maximum water level.

To prevent the risk of

burns, use caution when filling a hot iron with water. Burns can

occur from touching hot metal parts, hot water or steam.

Push firmly

to close the cover.

N

OTE

:

Tap water may be used due to the special design of this iron.

However, in areas with very hard water, distilled or demineralized water is recommended.

• Turn the temperature dial to any of the temperatures within the steam band and allow

the iron to heat for approximately 2 minutes before ironing. While heating, place iron

on heel rest on a stable, protected surface.

• Adjust Steam Dial to desired level of steaming.

SHOT OF STEAM

®

FEATURE

• The SHOT OF STEAM

®

feature provides an extra burst of steam for deep penetration

of stubborn wrinkles. The SHOT OF STEAM

®

feature can be used with dry or steam

ironing provided the tank is at least 1/2 full of water and the Temperature Dial is set

within the steam band.

• Allow the iron to heat for approximately 2 minutes.

• Press the SHOT OF STEAM

®

button several times to prime the pump.

• Pump SHOT OF STEAM

®

button another three to four times in order to clean the unit.

The SHOT OF STEAM

®

feature is now ready for use. The SHOT OF STEAM

®

feature

can be used continously with just a short pause between shots. The SHOT OF STEAM

®

feature is most effective with the iron held in a horizontal position just above the fabric

being ironed.

• If the tank runs dry, unplug the iron and refill with water. The iron may be filled with

water while it is hot.

N

OTE

:

It may be necessary to re-prime the pump before using

the SHOT OF STEAM

®

feature again.

SPRAY

MIST

®

FEATURE

• Use the SPRAY MIST

®

feature to dampen fabrics with stubborn wrinkles.

• Press the gray SPRAY MIST

®

button firmly to produce spray.

SAFETY S

MART

®

FEATURE

AUTO SHUT-OFF

• When the iron is plugged into 230 volt AC electrical outlet, the steady red light signals

that the iron is powered in and is ready to be used.

• If the iron is left on the heel rest unmoved the iron will stop heating in 15 minutes.

The light on the handle will blink to indicate the iron has automatically

shut off and will continue blinking until the iron is restarted or unplugged.

• If the iron is left unmoved in the ironing position or accidentally tipped over, the iron

will stop heating in 30 seconds.

Again, the light on the handle will blink to

indicate the iron has automatically shut off and will continue blinking

until the iron is restarted or unplugged.

•

N

OTE

:

If the Temperature Dial is turned to the Off position, light will continue

blinking and then go off.

• To restart the iron move the iron back and forth. Allow the iron to heat and continue

ironing as normal.

•

N

OTE

:

Although heat is no longer generated once the iron has automatically shut off,

allow sufficient time for the iron to cool before touching the soleplate or storing

the iron.

NON-STICK FINISH

• Non-Stick coating prevents sticking of fabrics and starch residue to the soleplate.

• To clean the soleplate, allow iron to cool and wipe with a soft cloth using

a mild vinegar solution.

• Do not use scouring pads, abrasives or chemical cleaning solvents as they

may damage the finish.

•

N

OTE

:

Scratches in the non-stick soleplate do not affect the performance of the iron.

Évaluation

En savoir plus sur ce mode d’emploi

Nous comprenons qu’il est agréable d’avoir un mode d’emploi papier pour vos Sunbeam 3946 Steam Master Deluxe Fer à repasser. Vous pouvez toujours télécharger le mode d’emploi depuis notre site Web et l’imprimer vous-même. Si vous souhaitez disposer d’un mode d’emploi original, nous vous recommandons de contacter Sunbeam. Ils pourront peut-être fournir un mode d’emploi original. Recherchez-vous le mode d’emploi de votre Sunbeam 3946 Steam Master Deluxe Fer à repasser dans une autre langue ? Choisissez votre langue préférée sur notre page d’accueil et recherchez le numéro de modèle pour voir si nous l’avons disponible.

Caractéristiques

Tous les modes d’emploi pour Sunbeam Fers à repasser
Plus de modes d’emploi de Fers à repasser

Foire aux questions sur Sunbeam 3946 Steam Master Deluxe Fer à repasser

Notre équipe d’assistance recherche des informations utiles sur les produits et des réponses aux questions fréquemment posées. Si vous trouvez une inexactitude dans notre foire aux questions, veuillez nous le faire savoir en utilisant notre formulaire de contact.

Produits connexes

Mode d’emploi

Sunbeam 4215 Steam Master Fer à repasser

Mode d’emploi

Sunbeam IR5272 Fer à repasser

Mode d’emploi

Sunbeam 3964-099 Classic Fer à repasser

Mode d’emploi

Sunbeam 3965-099 Classic Fer à repasser

Mode d’emploi

Sunbeam 3051 Simple Press Fer à repasser

Mode d’emploi

Sunbeam 3062 Simple Press Fer à repasser

Mode d’emploi

Sunbeam GCSBBV-102 Fer à repasser

Mode d’emploi

Sunbeam 4212 Steam Master Fer à repasser

Catégories associées