Mode d’emploi Vonroc HA502AC Décapeur thermique

Mode d’emploi

EN

5

WWW.VONROC.COM

nore tool safety principles. A careless action can

cause severe injury within a fraction of a second.

4) Power tool use and care

a) Do not force the power tool. Use the correct

power tool for your application. The correct

power tool will do the job better and safer at the

rate for which it was designed.

b) Do not use the power tool if the switch does not

turn it on and off. Any power tool that cannot

be controlled with the switch is dangerous and

must be repaired.

c) Disconnect the plug from the power source

and/or the battery pack from the power tool be-

fore making any adjustments, changing acces-

sories, or storing power tools. Such preventive

safety measures reduce the risk of starting the

power tool accidentally.

d) Store idle power tools out of the reach of child-

ren and do not allow persons unfamiliar with

the power tool or these instructions to operate

the power tool. Power tools are dangerous in

the hands of untrained users.

e) Maintain power tools. Check for misalignment

or binding of moving parts, breakage of parts

and any other condition that may affect the

power tool’s operation. If damaged, have the

power tool repaired before use. Many accidents

are caused by poorly maintained power tools.

f)

Keep cutting tools sharp and clean. Properly

maintained cutting tools with sharp cutting edges

are less likely to bind and are easier to control.

g) Use the power tool, accessories and tool bits

etc. in accordance with these instructions,

taking into account the working conditions and

the work to be performed. Use of the power tool

for operations different from those intended

could result in a hazardous situation.

h)

Keep handles and grasping surfaces dry, clean

and free from oil and grease. Slippery handles and

grasping surfaces do not allow for safe handling

and control of the tool in unexpected situations.

5) Battery tool use and care

a) Recharge only with the charger specified by the

manufacturer. A charger that is suitable for one

type of battery pack may create a risk of fire

when used with another battery pack.

b) Use power tools only with specifically design-

ated battery packs. Use of any other battery

packs may create a risk of injury and fire.

c)

When battery pack is not in use, keep it away

from other metal objects, like paper clips, coins,

keys, nails, screws or other small metal objects

that can make a connection from one terminal to

another. Shorting the battery terminals together

may cause burns or a fire.

d)

Under abusive conditions, liquid may be ejected

from the battery; avoid contact. If contact

accidentally occurs, flush with water. If liquid

contacts eyes, additionally seek medical help.

Liquid ejected from the battery may cause

irritation or burns.

e) Do not use a battery pack or tool that is dama-

ged or modified. Damaged or modified batteries

may exhibit unpredictable behaviour resulting in

fire, explosion or risk of injury.

f)

Do not expose a battery pack or tool to fire

or excessive temperature. Exposure to fire or

temperature above 130 °C may cause explosion.

NOTE The temperature „130 °C“ can be replaced

by the temperature „265 °F“.

g)

Follow all charging instructions and do not

charge the battery pack or tool outside the

temperature range specified in the instructions.

Charging improperly or at temperatures outside

the specified range may damage the battery and

increase the risk of fire.

6) Service

a) Have your power tool serviced by a qualified

repair person using only identical replacement

parts. This will ensure that the safety of the

power tool is maintained.

b)

Never service damaged battery packs. Service

of battery packs should only be performed by the

manufacturer or authorized service providers.

ADDITIONAL SAFETY WARNINGS FOR HOT

AIR GUN

Before using the appliance check the following:

Make sure the voltage of the hot air gun

corresponds with the power voltage; Are

the mains lead and the mains plug in a

good state: strong, without ravels or

damages.

• Avoid the use of long extension cables;

• Do not use the appliance under moist circum-

stances;

• The metal mouthpiece gets hot. Watch out and

do not touch the metal mouthpiece;

Évaluation

En savoir plus sur ce mode d’emploi

Nous comprenons qu’il est agréable d’avoir un mode d’emploi papier pour vos Vonroc HA502AC Décapeur thermique. Vous pouvez toujours télécharger le mode d’emploi depuis notre site Web et l’imprimer vous-même. Si vous souhaitez disposer d’un mode d’emploi original, nous vous recommandons de contacter Vonroc. Ils pourront peut-être fournir un mode d’emploi original. Recherchez-vous le mode d’emploi de votre Vonroc HA502AC Décapeur thermique dans une autre langue ? Choisissez votre langue préférée sur notre page d’accueil et recherchez le numéro de modèle pour voir si nous l’avons disponible.

Caractéristiques

Tous les modes d’emploi pour Vonroc Décapeurs thermiques
Plus de modes d’emploi de Décapeurs thermiques

Foire aux questions sur Vonroc HA502AC Décapeur thermique

Notre équipe d’assistance recherche des informations utiles sur les produits et des réponses aux questions fréquemment posées. Si vous trouvez une inexactitude dans notre foire aux questions, veuillez nous le faire savoir en utilisant notre formulaire de contact.

Produits connexes

Mode d’emploi

Vonroc HA501AC Décapeur thermique

Mode d’emploi

Parkside IAN 46460 Décapeur thermique

Mode d’emploi

Einhell TC-HA 2000/1 Décapeur thermique

Mode d’emploi

Steinel HL 1820 S Décapeur thermique

Mode d’emploi

Weldy HG 530-S Décapeur thermique

Mode d’emploi

Hyundai HD2000 Décapeur thermique

Mode d’emploi

Cecotec Hell Gun 7500 Full Equip Décapeur thermique

Mode d’emploi

Parkside IAN 385161 Décapeur thermique

Catégories associées