Mode d’emploi Worx WX420L Scie circulaire

Mode d’emploi

4

Mini Circular Saw EN

use of tools allow you to become

complacent and ignore tool safety

principles. A careless action can cause severe

injury within a fraction of a second.

4) Power tool use and care

a) Do not force the power tool. Use the

correct power tool for your application. The

correct power tool will do the job better and safer

at the rate for which it was designed.

b) Do not use the power tool if the switch

does not turn it on and off. Any power tool

that cannot be controlled with the switch is

dangerous and must be repaired.

c) Disconnect the plug from the power

source and/or remove the battery pack,

if detachable, from the power tool before

making any adjustments, changing

accessories, or storing power tools. Such

preventive safety measures reduce the risk of

starting the power tool accidentally.

d) Store idle power tools out of the reach of

children and do not allow persons unfamiliar

with the power tool or these instructions

to operate the power tool. Power tools are

dangerous in the hands of untrained users.

e) Maintain power tools and accessories.

Check for misalignment or binding of

moving parts, breakage of parts and any

other condition that may affect the power

tool’s operation. If damaged, have the

power tool repaired before use. Many

accidents are caused by poorly maintained power

tools.

f) Keep cutting tools sharp and clean. Properly

maintained cutting tools with sharp cutting edges

are less likely to bind and are easier to control.

g) Use the power tool, accessories and

tool bits etc. in accordance with these

instructions, taking into account the

working conditions and the work to be

performed. Use of the power tool for operations

different from those intended could result in a

hazardous situation.

h) Keep handles and grasping surfaces dry,

clean and free from oil and grease. Slippery

handles and grasping surfaces do not allow

for safe handling and control of the tool in

unexpected situations.

5) Service

a) Have your power tool serviced by a

qualified repair person using only identical

replacement parts. This will ensure that the

safety of the power tool is maintained.

SAFETY INSTRUCTIONS

FOR ALL SAWS

CUTTING PROCEDURES

a) DANGER: Keep hands away from

cutting area and the blade. If both

hands are holding the saw, they cannot be cut by

the blade.

b) Do not reach underneath the workpiece. The

guard cannot protect you from the blade below

the workpiece.

c) Adjust the cutting depth to the thickness

of the workpiece. Less than a full tooth of

the blade teeth should be visible below the

workpiece.

d) Never hold workpiece in your hands or

across your leg while cutting. Secure the

workpiece to a stable platform. It is important

to support the work properly to minimise body

exposure, blade binding, or loss of control.

e) Hold the power tool by insulated gripping

surfaces only, when performing an

operation where the cutting tool may

contact hidden wiring or its own cord.

Contact with a “live” wire will also make exposed

metal parts of the power tool “live” and could

give the operator an electric shock.

f) When ripping always use a rip fence or

straight edge guide. This improves the accuracy

of cut and reduces the chance of blade binding.

g) Always use blades with correct size and

shape (diamond versus round) of arbour

holes. Blades that do not match the mounting

hardware of the saw will run off-centre, causing

loss of control.

h) Never use damaged or incorrect blade

washers or bolt. The blade washers and

bolt were specially designed for your saw, for

optimum performance and safety of operation.

FURTHER SAFETY

INSTRUCTIONS FOR ALL

SAWS

Kickback causes and related warnings

— kickback is a sudden reaction to a pinched, bound

or misaligned saw blade, causing an uncontrolled

saw to lift up and out of the workpiece toward the

operator;

— when the blade is pinched or bound tightly by the

kerf closing down, the blade stalls and the motor

reaction drives the unit rapidly back toward the

operator;

— if the blade becomes twisted or misaligned in the

cut, the teeth at the back edge of the blade can dig

into the top surface of the wood causing the blade

to climb out of the kerf and jump back toward the

operator.

Kickback is the result of saw misuse and/or incorrect

operating procedures or conditions and can be

avoided by taking proper precautions as given below.

a) Maintain a firm grip on the saw and position

your arms to resist kickback forces.

Position your body to either side of the

blade, but not in line with the blade. Kickback

could cause the saw to jump backwards, but

kickback forces can be controlled by the operator,

if proper precautions are taken.

Évaluation

En savoir plus sur ce mode d’emploi

Nous comprenons qu’il est agréable d’avoir un mode d’emploi papier pour vos Worx WX420L Scie circulaire. Vous pouvez toujours télécharger le mode d’emploi depuis notre site Web et l’imprimer vous-même. Si vous souhaitez disposer d’un mode d’emploi original, nous vous recommandons de contacter Worx. Ils pourront peut-être fournir un mode d’emploi original. Recherchez-vous le mode d’emploi de votre Worx WX420L Scie circulaire dans une autre langue ? Choisissez votre langue préférée sur notre page d’accueil et recherchez le numéro de modèle pour voir si nous l’avons disponible.

Caractéristiques

Tous les modes d’emploi pour Worx Scies circulaires
Plus de modes d’emploi de Scies circulaires

Foire aux questions sur Worx WX420L Scie circulaire

Notre équipe d’assistance recherche des informations utiles sur les produits et des réponses aux questions fréquemment posées. Si vous trouvez une inexactitude dans notre foire aux questions, veuillez nous le faire savoir en utilisant notre formulaire de contact.

Produits connexes

Mode d’emploi

Worx WX439L Scie circulaire

Mode d’emploi

Worx WX523.9 Scie circulaire

Mode d’emploi

Worx WX520L.9 Scie circulaire

Mode d’emploi

Worx WX429L Scie circulaire

Mode d’emploi

Worx WX530 Scie circulaire

Mode d’emploi

Worx WX529.9 Scie circulaire

Mode d’emploi

Worx WX531L Scie circulaire

Mode d’emploi

Worx WX531L.9 Scie circulaire

Catégories associées