Mode d’emploi Worx WX420L Scie circulaire

Mode d’emploi

5

Mini Circular Saw EN

b) When blade is binding, or when interrupting

a cut for any reason, release the trigger and

hold the saw motionless in the material until

the blade comes to a complete stop. Never

attempt to remove the saw from the work

or pull the saw backward while the blade is

in motion or kickback may occur. Investigate

and take corrective actions to eliminate the cause

of blade binding.

c) When restarting a saw in the workpiece,

centre the saw blade in the kerf and check

that saw teeth are not engaged into the

material. If saw blade is binding, it may walk

up or kickback from the workpiece as the saw is

restarted.

d) Support large panels to minimise the risk

of blade pinching and kickback. Large panels

tend to sag under their own weight. Supports

must be placed under the panel on both sides,

near the line of cut and near the edge of the

panel.

e) Do not use dull or damaged blades.

Unsharpened or improperly set blades produce

narrow kerf causing excessive friction, blade

binding and kickback.

f) Blade depth and bevel adjusting locking

levers must be tight and secure before

making cut. If blade adjustment shifts while

cutting, it may cause binding and kickback.

g) Use extra caution when sawing into

existing walls or other blind areas. The

protruding blade may cut objects that can cause

kickback.

SAFETY INSTRUCTIONS

FOR PLUNGE TYPE SAW

Guard function

a) Check guard for proper closing before

each use. Do not operate the saw if guard

does not move freely and enclose the

blade instantly. Never clamp or tie the

guard so that the blade is exposed. If saw is

accidentally dropped, guard may be bent. Check

to make sure that guard moves freely and does

not touch the blade or any other part, in all angles

and depths of cut.

b) Check the operation and condition of the

guard return spring. If the guard and the

spring are not operating properly, they

must be serviced before use. Guard may

operate sluggishly due to damaged parts, gummy

deposits, or a build-up of debris.

c) Assure that the base plate of the saw will

not shift while performing the “plunge cut”

when the blade bevel setting is not at 90°.

Blade shifting sideways will cause binding and

likely kick back.

d) Always observe that the guard is covering

the blade before placing saw down on

bench or floor. An unprotected, coasting blade

will cause the saw to walk backwards, cutting

whatever is in its path. Be aware of the time it

takes for the blade to stop after switch is released.

ADDITIONAL SAFETY

RULES FOR YOUR

CIRCULAR SAW

1. Only use saw blades recommended in the

specification.

2. Do not use any abrasive wheels.

3. Use only blade diameter(s) in accordance with the

markings.

4. Identify the correct saw blade to be used for the

material to be cut.

5. Use only saw blades that are marked with a speed

equal or higher than the speed marked on the

tool.

CUT-OFF MACHINE SAFETY

WARNINGS

a) The guard provided with the tool must be

securely attached to the power tool and

positioned for maximum safety, so the least

amount of wheel is exposed towards the

operator. Position yourself and bystanders

away from the plane of the rotating wheel.

The guard helps to protect operator from broken

wheel fragments and accidental contact with

wheel.

b) Use only bonded reinforced or diamond cut-

off wheels for your power tool. Just because

an accessory can be attached to your power tool,

it does not assure safe operation.

c) The rated speed of the accessory must

be at least equal to the maximum speed

marked on the power tool. Accessories

running faster than their rated speed can break

and fly apart.

d) Wheels must be used only for recommended

applications. For example: do not grind with

the side of cut-off wheel. Abrasive cut-off

wheels are intended for peripheral grinding, side

forces applied to these wheels may cause them to

shatter.

e) Always use undamaged wheel flanges that

are of correct diameter for your selected

wheel. Proper wheel flanges support the wheel

thus reducing the possibility of wheel breakage.

f) Do not use worn down reinforced wheels

from larger power tools. Wheels intended for

a larger power tool are not suitable for the higher

speed of a smaller tool and may burst.

g) The outside diameter and the thickness of

your accessory must be within the capacity

rating of your power tool. Incorrectly sized

accessories cannot be adequately guarded or

Évaluation

En savoir plus sur ce mode d’emploi

Nous comprenons qu’il est agréable d’avoir un mode d’emploi papier pour vos Worx WX420L Scie circulaire. Vous pouvez toujours télécharger le mode d’emploi depuis notre site Web et l’imprimer vous-même. Si vous souhaitez disposer d’un mode d’emploi original, nous vous recommandons de contacter Worx. Ils pourront peut-être fournir un mode d’emploi original. Recherchez-vous le mode d’emploi de votre Worx WX420L Scie circulaire dans une autre langue ? Choisissez votre langue préférée sur notre page d’accueil et recherchez le numéro de modèle pour voir si nous l’avons disponible.

Caractéristiques

Tous les modes d’emploi pour Worx Scies circulaires
Plus de modes d’emploi de Scies circulaires

Foire aux questions sur Worx WX420L Scie circulaire

Notre équipe d’assistance recherche des informations utiles sur les produits et des réponses aux questions fréquemment posées. Si vous trouvez une inexactitude dans notre foire aux questions, veuillez nous le faire savoir en utilisant notre formulaire de contact.

Produits connexes

Mode d’emploi

Worx WX439L Scie circulaire

Mode d’emploi

Worx WX523.9 Scie circulaire

Mode d’emploi

Worx WX520L.9 Scie circulaire

Mode d’emploi

Worx WX429L Scie circulaire

Mode d’emploi

Worx WX530 Scie circulaire

Mode d’emploi

Worx WX529.9 Scie circulaire

Mode d’emploi

Worx WX531L Scie circulaire

Mode d’emploi

Worx WX531L.9 Scie circulaire

Catégories associées