Mode d’emploi DeWalt DW317 Scie sauteuse

Mode d’emploi

OPERATION

WARNING: To reduce the risk of serious personal injury, turn tool off and disconnect

tool from power source before making any adjustments or removing/installing

attachments or accessories.

Trigger Switch (Fig. 1)

To start the jig saw, squeeze the trigger switch (A).

To slow and stop the jig saw, release the trigger switch.

For continuous operation, squeeze the trigger switch then depress the lock button (B). Once

lock button is depressed, release the trigger switch.

To release from continuous operation, squeeze the trigger and the lock will disengage.

Variable Speed Switch (Fig. 1, 2)

The variable speed is controlled in two ways: speed control dial (C) and the trigger switch

(A).

SPEED CONTROL DIAL

By rotating the speed control dial (C) in either direction, the maximum speed or strokes-per-

minute at which the blade will cut is adjusted. The speed control dial adjusts the speed that

the blade will cut from approximately 500 SPM to approximately 3,100 SPM.

TRIGGER SWITCH

As the trigger switch is pressed in, the strokes-per-minute continue to increase, but not to

exceed the maximum setting on the speed control dial. As the trigger is released, the blade

strokes-per-minute reduce.

Blade Installation and Removal (Fig. 3)

TO INSTALL A BLADE

1. Lift the keyless blade lever (D).

2. Insert the blade into the clamp mechanism (F) while guiding the back of the blade into the

groove of the guide rollers (G).

3. The shank should be completely inside the clamp mechanism as shown in Figure 4.

4. Release the keyless blade lever.

TO REMOVE A BLADE

1. Lift the keyless blade lever (D).

2. With a slight shake the blade will drop out.

CAUTION: Do not touch used blades, they may be hot. Personal injury may result.

Bevel Cutting Adjustment (Fig. 5)

Bevel cuts may be made at any angle between 0° and 45°. The shoe is adjusted by loosening

the screw (H) on the bottom of the tool and rotating the shoe to the desired angle. After setting

the shoe, tighten the screw firmly and use saw in the normal manner.

Cutting Action – Orbital or Straight (Fig. 6)

CAUTION: Check that the tool is not locked ON before connecting it to a power supply. If

the trigger switch is locked ON when the tool is connected to the power supply, it will start

immediately. Damage to your tool or personal injury may result.

This jig saw is equipped with four cutting actions, three orbital and one straight. Orbital action

has a more aggressive blade motion and is designed for cutting in soft materials like wood

or plastic. Orbital action provides a faster cut, but with a rougher cut across the material. In

orbital action, the blade moves forward during the cutting stroke in addition to the up and down

motion.

NOTE: Metal or hardwoods should never be cut in orbital action.

To adjust the cutting action, move the cutting action lever (I) between the four cutting

positions: 0, 1, 2, and 3. Position 0 is straight cutting. Positions 1, 2, and 3 are orbital cutting.

The aggressiveness of the cut increase as the lever is adjusted from one to three, with three

being the most aggressive cut.

Adjustment For 90° Cuts

1. The 0° mark on the quadrant plate should line up with mark on shoe.

2. If adjustment is necessary, loosen screw on quadrant plate and adjust as necessary.

Place a right angle against the blade and the shoe and adjust the shoe to 90°.

Anti-Splintering (Fig. 7)

This jig saw has a special double-ended shoe with a wide opening at one end for general

cutting and bevel cutting and a very narrow slot at the other end for use only with hollow

ground blades.This narrow slot acts as an anti-splintering device (J) particularly useful when

cutting plywood.

Reversing Shoe Position (Fig. 7)

To reverse the shoe position remove the screw (H) from the bottom of the tool, as shown in

Figure 8, and remove the shoe from the jig saw. [Be careful to note the position of the clamp

(K). This clamp must be re-installed the same way or the shoe will not fit properly.] Turn the

shoe around and re-install noting carefully that, when the slot is forward, the screw goes

through the hole in the shoe and when the wide opening is forward, the screw passes through

the slot in the shoe.

Cutting

WARNING: The jig saw should not be operated with the shoe removed or serious personal

injury may result.

POCKET CUTTING (FIG. 8, 9)

A pocket cut is an easy method of making an inside cut. The saw can be inserted directly

into a panel or board without first drilling a lead or pilot hole. In pocket cutting, measure the

surface to be cut and mark clearly with a pencil. Next tip the saw forward until the front end of

the shoe sits firmly on the work surface and the blade clears the work through its full stroke.

Switch the tool on and allow it to attain maximum speed. Grip the saw firmly and lower the

back edge of tool slowly until the blade reaches its complete depth. Hold the shoe flat against

the wood and begin cutting. Do not remove blade from cut while it is still moving. Blade must

come to a complete stop.

WOOD CUTTING

Support the workpiece adequately at all times. Use the higher speed setting for cutting wood.

Do not attempt to turn the tool on when blade is against material to be cut. This could stall

the motor. Place the front of shoe on the material to be cut and hold the jig saw shoe firmly

against the wood while cutting. Don’t force the tool; let the blade cut at its own speed. When

the cut is complete, turn the jig saw off. Let blade come to a complete stop and then lay the

saw aside before loosening the work.

METAL CUTTING

In cutting thin gauge sheet metals, it is best to clamp wood to the bottom of sheet metal; this

will insure a clean cut without the risk of vibration or tearing of metal. Always remember to use

a finer blade for ferrous metals (for those that have a high iron content); and use a coarser

blade for non-ferrous metals (those that do not have an iron content). Use a high speed setting

for cutting soft metals (aluminum, copper, brass, mild steel, galvanized pipe, conduit sheet

metal, etc.). Use lower speed to cut plastics, tile, laminate, hard metals, and cast iron.

MAINTENANCE

WARNING: To reduce the risk of serious personal injury, turn tool off and disconnect

tool from power source before making any adjustments or removing/installing

attachments or accessories.

Cleaning

WARNING: Blow dirt and dust out of all air vents with clean, dry air at least once a week.

To minimize the risk of eye injury, always wear ANSI Z87.1 approved eye protection when

performing this.

WARNING: Never use solvents or other harsh chemicals for cleaning the non-metallic parts

of the tool. These chemicals may weaken the plastic materials used in these parts. Use a cloth

dampened only with water and mild soap. Never let any liquid get inside the tool; never

immerse any part of the tool into a liquid.

Lubrication

NOTE: NEVER spray or in any other way apply lubricants or cleaning solvents inside the tool.

This can seriously affect the life and performance of the tool.

FIG. 2

C

FIG. 6

I

FIG. 5

15°

30°

45°

FIG. 8

FIG. 9

FIG. 1 B

A

I

C

D

E

FIG. 3

FIG. 7

FIG. 4

J

G

F

D

D

F

H

H

K

E

Évaluation

En savoir plus sur ce mode d’emploi

Nous comprenons qu’il est agréable d’avoir un mode d’emploi papier pour vos DeWalt DW317 Scie sauteuse. Vous pouvez toujours télécharger le mode d’emploi depuis notre site Web et l’imprimer vous-même. Si vous souhaitez disposer d’un mode d’emploi original, nous vous recommandons de contacter DeWalt. Ils pourront peut-être fournir un mode d’emploi original. Recherchez-vous le mode d’emploi de votre DeWalt DW317 Scie sauteuse dans une autre langue ? Choisissez votre langue préférée sur notre page d’accueil et recherchez le numéro de modèle pour voir si nous l’avons disponible.

Caractéristiques

Tous les modes d’emploi pour DeWalt Scies sauteuses
Plus de modes d’emploi de Scies sauteuses

Foire aux questions sur DeWalt DW317 Scie sauteuse

Notre équipe d’assistance recherche des informations utiles sur les produits et des réponses aux questions fréquemment posées. Si vous trouvez une inexactitude dans notre foire aux questions, veuillez nous le faire savoir en utilisant notre formulaire de contact.

Produits connexes

Mode d’emploi

DeWalt DW318 Scie sauteuse

Mode d’emploi

DeWalt DCS331 Scie sauteuse

Mode d’emploi

DeWalt DW323 Scie sauteuse

Mode d’emploi

DeWalt DW313 Scie sauteuse

Mode d’emploi

DeWalt DW320K Scie sauteuse

Mode d’emploi

DeWalt DC330 Scie sauteuse

Mode d’emploi

DeWalt DW318G Scie sauteuse

Mode d’emploi

DeWalt DC308K Scie sauteuse

Catégories associées