Mode d’emploi Mellerware 20800A Tondeuse

Mode d’emploi

3.4. Adjusting the blade lever:

3.4.1. The lever is conveniently located above the on/

off switch so it can easily be adjusted while the clipper

is in your hand.

3.4.2. The lever adds versatility to the clipper by allow-

ing a gradual change to the length of a cut without an

attachment comb.

3.4.3. When the lever is in the uppermost position, the

blades will give the closest cut leaving the hair very

short. Pushing the lever gradually downward increases

the cutting length.

3.4.4. In its lowest position, the lever will leave the hair

approximately the same length as a #1 comb.

3.4.5. The lever will also extend the blade’s life as a

longer cut requires less work from the blades.

3.4.6. While the clipper is running, move the Lever

from “close cut” to “longer cut” a number of times.

This will help keep cut hair away from the blades. If the

clipper stops cutting, and the method above does not

help, then the blades are blunt and need to be replaced.

3.5. Guide combs:

3.5.1. Each comb attachment is marked accordingly on

the outside surface.

3.5.2. To attach a comb, hold the comb with the teeth

showing upward and slide it onto and along the clipper

blade until the front of the comb firmly clicks into the

clipper blade.

3.5.3. To remove the comb, simply pull the comb

upward and away from the clipper blade.

• Attachment Comb #1 leaves 3mm hair length.

• Attachment Comb #2 leaves 6mm hair length.

• Attachment Comb #3 leaves 9mm hair length.

• Attachment Comb #4 leaves 12mm hair length.

blade.

3.6. Preparation for the hair cut:

3.6.1. Inspect the clipper, making sure that it is free

of oil between the cutting blade teeth. Switch on the

unit to distribute the oil and to ensure that it is running

smoothly. Wipe off any excess oil. (This should be

done after each use). Unwind and straighten the cord

during use in order to avoid tangling.

3.6.2. Ensure that the person that is going to have their

hair cut is properly seated and that the hair to be cut

is at eye level. This allows visibility while cutting and

control of the clipper.

3.6.3. Make sure that hair is dry for using the clipper.

3.6.4. Before cutting hair, brush/comb the hair so that it

is straight & tangle free.

3.6.5. Place a towel around the neck and shoulders of

the person having the haircut.

3.6.6. NB: Cutting hair requires practice. When cutting

for the first time, always use a longer comb and then

change combs to cut hair shorter if required/ preferred.

3.7. Cutting the hair:

3.7.1.Nape of the neck

1. Attach guide comb attachment #1 or #2.

2. Hold the clipper cutting edge pointing upwards and

begin the haircut, starting in the middle of the base of

the neck (see diagram 1).

3. Hold the clipper comfortably in your hand and hold

lightly against the head with the comb teeth pointing

upward. Gradually and slowly lift the clipper working

upwards and outwards, through the hair, trimming just

a little at a time.

4. As you cut, gradually lift the clipper head towards

you. Continue to cut the back area from the bottom of

the neck upwards to the top of the ears.

3.7.2. Back of the head

1. Change to the next longest guide comb attachment

#3 or #4 and cut the hair on the back of the head (see

diagram 2).

Close cut

Longer cut

DIAGRAM 1

DIAGRAM 2

Évaluation

En savoir plus sur ce mode d’emploi

Nous comprenons qu’il est agréable d’avoir un mode d’emploi papier pour vos Mellerware 20800A Tondeuse. Vous pouvez toujours télécharger le mode d’emploi depuis notre site Web et l’imprimer vous-même. Si vous souhaitez disposer d’un mode d’emploi original, nous vous recommandons de contacter Mellerware. Ils pourront peut-être fournir un mode d’emploi original. Recherchez-vous le mode d’emploi de votre Mellerware 20800A Tondeuse dans une autre langue ? Choisissez votre langue préférée sur notre page d’accueil et recherchez le numéro de modèle pour voir si nous l’avons disponible.

Caractéristiques

Tous les modes d’emploi pour Mellerware Tondeuses
Plus de modes d’emploi de Tondeuses

Foire aux questions sur Mellerware 20800A Tondeuse

Notre équipe d’assistance recherche des informations utiles sur les produits et des réponses aux questions fréquemment posées. Si vous trouvez une inexactitude dans notre foire aux questions, veuillez nous le faire savoir en utilisant notre formulaire de contact.

Produits connexes

Mode d’emploi

SilverCrest IAN 377184 Tondeuse

Mode d’emploi

Taurus HC-0150 Tondeuse

Mode d’emploi

Camry CR 2844 Tondeuse

Mode d’emploi

Ufesa MB6000 Skipper Tondeuse

Mode d’emploi

Cecotec PrecisionCare AllDrive Pro Tondeuse

Mode d’emploi

Livoo DOS229N Tondeuse

Mode d’emploi

Tristar TR-2572 Tondeuse

Mode d’emploi

G3 Ferrari G30038 Appeal Tondeuse

Catégories associées