Mode d’emploi Ryobi AG4031G Meuleuse angulaire

Mode d’emploi

3 - English

ANGLE GRINDER SAFETY WARNINGS

SAFETY WARNINGS COMMON FOR GRIND-

ING, SANDING, WIRE BRUSHING AND POLISH-

ING OPERATIONS

 This power tool is intended to function as a grinder,

sander, wire brush, or polisher. Read all safety warn-

ings, instructions, illustrations and specifications

provided with this power tool. Failure to follow all in-

structions listed below may result in electric shock, fire

and/or serious injury.

 Operations such as cutting-off are not recommended

to be performed with this power tool. Operations for

which the power tool was not designed may create a

hazard and cause personal injury.

 Do not use accessories which are not specifically

designed and recommended by the tool manufacturer.

Just because the accessory can be attached to your

power tool, it does not assure safe operation.

The rated speed of the accessory must be at least

equal to the maximum speed marked on the power

tool. Accessories running faster than their rated speed

can break and fly apart.

 The outside diameter and the thickness of your acces-

sory must be within the capacity rating of your power

tool. Incorrectly sized accessories cannot be adequately

guarded or controlled.

 Threaded mounting of accessories must match the

grinder spindle thread. For accessories mounted by

flanges, the arbour hole of the accessory must fit the

locating diameter of the flange. Accessories that do not

match the mounting hardware of the power tool will run

out of balance, vibrate excessively and may cause loss

of control.

 Do not use a damaged accessory. Before each use in-

spect the accessory such as abrasive wheels for chips

and cracks, backing pad for cracks, tear or excess

wear, wire brush for loose or cracked wires. If power

tool or accessory is dropped, inspect for damage or

install an undamaged accessory. After inspecting and

installing an accessory, position yourself and bystand-

ers away from the plane of the rotating accessory and

run the power tool at maximum no-load speed for one

minute. Damaged accessories will normally break apart

during this test time.

 Wear personal protective equipment. Depending on

application, use face shield, safety goggles or safety

glasses. As appropriate, wear dust mask, hearing

protectors, gloves and workshop apron capable of

stopping small abrasive or workpiece fragments.

The eye protection must be capable of stopping

flying debris generated by various operations. The

eye protection must be capable of stopping flying debris

generated by various operations. The dust mask or

respirator must be capable of filtrating particles generated

by your operation. Prolonged exposure to high intensity

noise may cause hearing loss.

 Keep bystanders a safe distance away from work area.

Anyone entering the work area must wear personal

protective equipment. Fragments of workpiece or of a

broken accessory may fly away and cause injury beyond

immediate area of operation.

Hold the power tool by insulated gripping surfaces

only, when performing an operation where the cutting

accessory may contact hidden wiring or its own cord.

Cutting accessory contacting a “live” wire may make

exposed metal parts of the power tool “live” and shock

the operator.

 Position the cord clear of the spinning accessory. If

you lose control, the cord may be cut or snagged and your

hand or arm may be pulled into the spinning accessory.

 Never lay the power tool down until the accessory

has come to a complete stop. The spinning accessory

may grab the surface and pull the power tool out of your

control.

 Do not run the power tool while carrying it at your

side. Accidental contact with the spinning accessory

could snag your clothing, pulling the accessory into your

body.

 Regularly clean the power tool’s air vents. The motor’s

fan will draw the dust inside the housing and excessive

GENERAL POWER TOOL SAFETY WARNINGS

Use the power tool, accessories and tool bits etc.

in accordance with these instructions, taking into

account the working conditions and the work to be

performed. Use of the power tool for operations different

from those intended could result in a hazardous situation.

SERVICE

Have your power tool serviced by a qualified repair

person using only identical replacement parts. This will

ensure that the safety of the power tool is maintained.

When servicing a power tool, use only identical re-

placement parts. Follow instructions in the Mainte-

nance section of this manual. Use of unauthorized parts

or failure to follow Maintenance instructions may create

a risk of shock or injury.

Évaluation

En savoir plus sur ce mode d’emploi

Nous comprenons qu’il est agréable d’avoir un mode d’emploi papier pour vos Ryobi AG4031G Meuleuse angulaire. Vous pouvez toujours télécharger le mode d’emploi depuis notre site Web et l’imprimer vous-même. Si vous souhaitez disposer d’un mode d’emploi original, nous vous recommandons de contacter Ryobi. Ils pourront peut-être fournir un mode d’emploi original. Recherchez-vous le mode d’emploi de votre Ryobi AG4031G Meuleuse angulaire dans une autre langue ? Choisissez votre langue préférée sur notre page d’accueil et recherchez le numéro de modèle pour voir si nous l’avons disponible.

Caractéristiques

Tous les modes d’emploi pour Ryobi Meuleuses angulaires
Plus de modes d’emploi de Meuleuses angulaires

Foire aux questions sur Ryobi AG4031G Meuleuse angulaire

Notre équipe d’assistance recherche des informations utiles sur les produits et des réponses aux questions fréquemment posées. Si vous trouvez une inexactitude dans notre foire aux questions, veuillez nous le faire savoir en utilisant notre formulaire de contact.

Produits connexes

Mode d’emploi

Ryobi EAG-8512R Meuleuse angulaire

Mode d’emploi

Ryobi EAG750RS Meuleuse angulaire

Mode d’emploi

Ryobi R18AG-0 Meuleuse angulaire

Mode d’emploi

Ryobi RAG18X-0 Meuleuse angulaire

Mode d’emploi

Ryobi CAG180M Meuleuse angulaire

Mode d’emploi

Ryobi RAG18115-0 Meuleuse angulaire

Mode d’emploi

Ryobi RAG18125-0 Meuleuse angulaire

Mode d’emploi

Ryobi EAG750RB Meuleuse angulaire

Catégories associées