Mode d’emploi Ryobi AG4031G Meuleuse angulaire

Mode d’emploi

4 - English

accumulation of powdered metal may cause electrical

hazards.

 Do not operate the power tool near flammable

materials. Sparks could ignite these materials.

 Do not use accessories that require liquid coolants.

Using water or other liquid coolants may result in

electrocution or shock.

KICKBACK AND RELATED WARNINGS

Kickback is a sudden reaction to a pinched or snagged

rotating wheel, backing pad, brush or any other accessory.

Pinching or snagging causes rapid stalling of the rotating

accessory which in turn causes the uncontrolled power tool

to be forced in the direction opposite of the accessory’s

rotation at the point of the binding.

For example, if an abrasive wheel is snagged or pinched by

the workpiece, the edge of the wheel that is entering into the

pinch point can dig into the surface of the material causing

the wheel to climb out or kick out. The wheel may either jump

toward or away from the operator, depending on direction

of the wheel’s movement at the point of pinching. Abrasive

wheels may also break under these conditions.

Kickback is the result of power tool misuse and/or incorrect

operating procedures or conditions and can be avoided by

taking proper precautions as given below.

 Maintain a firm grip on the power tool and position

your body and arm to allow you to resist kickback

forces. Always use auxiliary handle, if provided, for

maximum control over kickback or torque reaction

during start-up. The operator can control torque

reactions or kickback forces, if proper precautions

are taken.

 Never place your hand near the rotating accessory.

Accessory may kickback over your hand.

 Do not position your body in the area where power

tool will move if kickback occurs. Kickback will propel

the tool in direction opposite to the wheel’s movement

at the point of snagging.

 Use special care when working corners, sharp edges

etc. Avoid bouncing and snagging the accessory.

Corners, sharp edges or bouncing have a tendency to

snag the rotating accessory and cause loss of control or

kickback.

 Do not attach a saw chain woodcarving blade or

toothed saw blade. Such blades create frequent

kickback and loss of control.

SAFETY WARNINGS SPECIFIC FOR GRINDING

OPERATIONS

 Use only wheel types that are recommended for your

power tool and the specific guard designed for the

selected wheel. Wheels for which the power tool was not

designed cannot be adequately guarded and are unsafe.

 The grinding surface of centre depressed wheels

must be mounted below the plane of the guard lip.

An improperly mounted wheel that projects through the

plane of the guard lip cannot be adequately protected.

 The guard must be securely attached to the power

tool and positioned for maximum safety, so the least

amount of wheel is exposed towards the operator.

The guard helps to protect operator from broken wheel

fragments and accidental contact with wheel.

 Wheels must be used only for recommended

applications. For example: do not grind with the side

of cut-off wheel. Abrasive cut-off wheels are intended for

peripheral grinding, side forces applied to these wheels

may cause them to shatter.

 Always use undamaged wheel flanges that are of

correct size and shape for your selected wheel.

Proper wheel flanges support the wheel thus reducing the

possibility of wheel breakage. Flanges for cut-off wheels

may be different from grinding wheel flanges.

 Do not use worn down wheels from larger power tools.

Wheel intended for larger power tool is not suitable for

the higher speed of a smaller tool and may burst.

SAFETY WARNINGS SPECIFIC FOR

SANDING OPERATIONS

 Do not use excessively oversized sanding disc

paper. Follow manufacturers recommendations,

when selecting sanding paper. Larger sanding paper

extending beyond the sanding pad presents a laceration

hazard and may cause snagging, tearing of the disc or

kickback.

SAFETY WARNINGS SPECIFIC FOR

POLISHING OPERATIONS

 Do not allow any loose portion of the polishing bonnet

or its attachment strings to spin freely. Tuck away or

trim any loose attachment strings. Loose and spinning

attachment strings can entangle your fingers or snag on

the workpiece.

SAFETY WARNINGS SPECIFIC FOR WIRE

BRUSHING OPERATIONS

 Be aware that wire bristles are thrown by the brush

even during ordinary operation. Do not overstress the

wires by applying excessive load to the brush. The wire

bristles can easily penetrate light clothing and/or skin.

 If the use of a guard is recommended for wire

brushing, do not allow any interference of the wire

wheel or brush with the guard. Wire wheel or brush

may expand in diameter due to work load and centrifugal

forces.

ANGLE GRINDER SAFETY WARNINGS

Évaluation

En savoir plus sur ce mode d’emploi

Nous comprenons qu’il est agréable d’avoir un mode d’emploi papier pour vos Ryobi AG4031G Meuleuse angulaire. Vous pouvez toujours télécharger le mode d’emploi depuis notre site Web et l’imprimer vous-même. Si vous souhaitez disposer d’un mode d’emploi original, nous vous recommandons de contacter Ryobi. Ils pourront peut-être fournir un mode d’emploi original. Recherchez-vous le mode d’emploi de votre Ryobi AG4031G Meuleuse angulaire dans une autre langue ? Choisissez votre langue préférée sur notre page d’accueil et recherchez le numéro de modèle pour voir si nous l’avons disponible.

Caractéristiques

Tous les modes d’emploi pour Ryobi Meuleuses angulaires
Plus de modes d’emploi de Meuleuses angulaires

Foire aux questions sur Ryobi AG4031G Meuleuse angulaire

Notre équipe d’assistance recherche des informations utiles sur les produits et des réponses aux questions fréquemment posées. Si vous trouvez une inexactitude dans notre foire aux questions, veuillez nous le faire savoir en utilisant notre formulaire de contact.

Produits connexes

Mode d’emploi

Ryobi EAG-8512R Meuleuse angulaire

Mode d’emploi

Ryobi EAG750RS Meuleuse angulaire

Mode d’emploi

Ryobi R18AG-0 Meuleuse angulaire

Mode d’emploi

Ryobi RAG18X-0 Meuleuse angulaire

Mode d’emploi

Ryobi CAG180M Meuleuse angulaire

Mode d’emploi

Ryobi RAG18115-0 Meuleuse angulaire

Mode d’emploi

Ryobi RAG18125-0 Meuleuse angulaire

Mode d’emploi

Ryobi EAG750RB Meuleuse angulaire

Catégories associées