Mode d’emploi Tefal FV7010K0 Fer à repasser

Mode d’emploi

For your safety

• Read these instructions carefully before using your appliance for the first time. If the product is not used

according to the instructions this will negate any guarantee and TEFAL cannot be held responsible.

• This appliance complies with the technical rules and standards for safety currently in force (Electromagnetic

Compatibility, Low Voltage, environment).

• This appliance is not intended for use by: children; or persons who may suffer from a mental and/or physical

impairment - unless they are adequately supervised in its operation and use.

Persons who have a limited or no understanding in the operation and use of this appliance must first read and

fully understand the contents of this instruction booklet, and where appropriate seek additional guidance on its

operation and use from the person responsible for their safety..

• Warning ! The voltage of your electrical installation must correspond to that of the iron (220V-240V). Connecting

to the wrong voltage may cause irreversible damage to the iron and will invalidate the guarantee.

• This iron must always be plugged into an earthed socket. If using a mains extension lead, ensure that it is

correctly rated (10A), with an earth.

• If the electrical cord becomes damaged, it must be immediately replaced by an Approved Service Centre to avoid

any danger.

• The appliance should not be used if it has fallen, if it has obvious damage, if it leaks or has functional anomalies.

Never dismantle your appliance: have it inspected by an Approved Service Centre, so as to avoid any danger.

• Never immerse your iron in water !

• Before being filled up or rinsed or before the water compartment is emptied or cleaned, the iron must always be

in the Cordless position and removed from its base.

• Do not unplug your appliance by pulling on the cord. Always unplug your appliance: before filling or rinsing the

water tank, before cleaning it, after each use.

• Never leave the appliance unattended when it is connected to a power source; nor if it has not cooled down for

approximately 1 hour.

• Your appliance gives off steam, which may cause burns, especially when you are ironing on a corner or at the

edge of your ironing board. Never direct the steam towards people or animals.

• Your iron should be used and placed on flat, stable, heat-resistant surface. When you put your iron onto its iron

rest, make sure that the surface on which you put it is stable.

• Never leave your appliance plugged in underneath its storage case (depending on the model)..

• Always remove the storage case (depending on the model) before using the appliance.

• Wait until the iron has cooled down before putting it away in its storage case.

• This product has been designed for domestic use only. Any commercial use, inappropriate use or failure to

comply with the instructions, the manufacturer accepts no responsibility and the guarantee will not apply.

• The iron must only be used with the supplied iron rest.

Preparation

• Remove the storage case (depending on the model). To do so, press down on the

top part of the locking hooks then lift up the lid –

fig.A.

•

Unravel the power cord.

• Put the switch into the Corded position –

fig.1 and remove the iron from

its base.

• You can use the attachment system – fig.2 to attach the base to one side of

your table– fig.3.

Before first use

• Before using your iron with the steam function for the first time, we recommend that

you operate it in a horizontal position for a few moments, away from your linen.

Under the same conditions, press the Boost of steam button a few times –

fig.4.

Description

1.

Spray nozzle

2. Anti-scale valve

3. Steam control

4. Filling inlet

5. Spray Button

6. Boost of steam button

7. Ergonomic grip

8. Temperature indicator light and

temperature setting indicator

9. Thermostat dial

10. Water tank max indicator

11. Soleplate

12. Storage case

(depending on model)

13. Carrying handle

14. Storage case locking and unlocking hooks

15. Base

16. System for attaching the base to your table

17. Connection block

18. Power cord clip

19. Electric power cord

20. 3-position switch:

a. Locking

for the transport and storage of your iron

b. With power cord to iron with the flex

c. Without power cord to iron without the flex

Please read these

instructions carefully.

Remove any labels

from the soleplate

before heating up the

iron.

4

1800113565_FV7XXX 7/04/08 17:11 Page 4

Évaluation

En savoir plus sur ce mode d’emploi

Nous comprenons qu’il est agréable d’avoir un mode d’emploi papier pour vos Tefal FV7010K0 Fer à repasser. Vous pouvez toujours télécharger le mode d’emploi depuis notre site Web et l’imprimer vous-même. Si vous souhaitez disposer d’un mode d’emploi original, nous vous recommandons de contacter Tefal. Ils pourront peut-être fournir un mode d’emploi original. Recherchez-vous le mode d’emploi de votre Tefal FV7010K0 Fer à repasser dans une autre langue ? Choisissez votre langue préférée sur notre page d’accueil et recherchez le numéro de modèle pour voir si nous l’avons disponible.

Caractéristiques

Tous les modes d’emploi pour Tefal Fers à repasser
Plus de modes d’emploi de Fers à repasser

Foire aux questions sur Tefal FV7010K0 Fer à repasser

Notre équipe d’assistance recherche des informations utiles sur les produits et des réponses aux questions fréquemment posées. Si vous trouvez une inexactitude dans notre foire aux questions, veuillez nous le faire savoir en utilisant notre formulaire de contact.

Produits connexes

Mode d’emploi

Tefal SV9203G0 Express Protect Fer à repasser

Mode d’emploi

Tefal GV9721E0 Fer à repasser

Mode d’emploi

Tefal FV2845T0 Fer à repasser

Mode d’emploi

Tefal SV6112E1 Fer à repasser

Mode d’emploi

Tefal SV6111E1 Fer à repasser

Mode d’emploi

Tefal FV8064G0 Fer à repasser

Mode d’emploi

Tefal FV2882G0 Fer à repasser

Mode d’emploi

Tefal GV9711E0 Fer à repasser

Catégories associées