Mode d’emploi Whirlpool WVW7336JS Hotte aspirante

Mode d’emploi

6

For Non-Vented (Recirculating) Installations

If it is not possible to vent cooking fumes and vapors to the

outside, the hood can be used in the non-vented (recirculating)

version, using a Recirculation Kit (which includes charcoal

lters and a deector). To order, see the “Assistance or Service”

section.

The ducting from this fan to the outside of the building has a

strong effect on the air ow, noise and energy use of the fan.

Use the shortest, straightest duct routing possible for best

performance, and avoid installing the fan with smaller ducts than

recommended.

Insulation around the ducts can reduce energy loss and inhibit

mold growth. Fans installed with existing ducts may not achieve

their rated airow.

*The recirculating version are neither Energy Star nor HVI certified.

Ensure duct joints and exterior penetrations are sealed with

caulk or other similar material to create an air-tight path and to

minimize building heat loss and gain and reduce the potential for

condensation.

Place/wrap insulation around duct and/or fan in order to

minimize possible condensation buildup within the duct, building

heat loss and gain.

Calculating Vent System Length

To calculate the length of the system you need, add the

equivalent feet (meters) for each vent piece used in the system.

Vent Piece 6" (15.2 cm) Round

45° elbow 2.5 ft (0.8 m)

90° elbow 5 ft (1.5 m)

Maximum equivalent vent length is 35 ft (10.7 m).

Example Vent System

The following example falls within the maximum

recommendedvent length of 35 ft (10.7 m).

1 - 90° Elbow = 5 ft (1.5 m)

1 - Wall cap = 0 ft (0 m)

8 ft (2.4 m) straight = 8 ft (2.4 m)

Length of system = 13 ft (3.9 m)

Electrical Requirements

Observe all governing codes and ordinances.

Ensure that the electrical installation is adequate and in

conformance with National Electrical Code, ANSI/NFPA 70

(latest edition), or CSA Standards C22.1-94, Canadian Electrical

Code, Part 1 and C22.2 No. 0-M91 (latest edition) and all local

codes and ordinances.

If codes permit and a separate ground wire is used, it is

recommended that a qualied electrician determine that the

ground path is adequate.

A copy of the above code standards can be obtained from:

National Fire Protection Association

1 Batterymarch Park

Quincy, MA 02169-7471

CSA International

8501 East Pleasant Valley Road

Cleveland, OH 44131-5575

■ A 120 volt, 60 Hz., AC only, 15-amp, fused electrical

circuitisrequired.

■ If the house has aluminum wiring, follow the

procedurebelow:

1. Connect a section of solid copper wire to the

pigtailleads.

2. Connect the aluminum wiring to the added section

of copper wire using special connectors and/or tools

designed and UL listed for joining copper to aluminum.

Follow the electrical connector manufacturer's

recommended procedure. Aluminum/copper connection

must conform with local codes and industry accepted wiring

practices.

■ Wire sizes and connections must conform with the rating of

the appliance as specied on the model/serial/rating plate.

The model/serial/rating plate is located behind the left lter

on the rear wall of the range hood.

■ Wire sizes must conform to the requirements of the National

Electrical Code, ANSI/NFPA 70 (latest edition), or CSA

Standards C22. 1-94, Canadian Electrical Code, Part 1 and

C22.2 No. 0-M91 (latest edition) and all local codes and

ordinances.

Non-Vented

(Recirculating)

Wall Venting

Roof Venting

C

B

A

C

B

A

C

B

A

A. Deflector

B. 6" (15.2 cm)

round vent

C Seal duct joints

with duct tape/

caulk

A. Wall cap

B. 6" (15.2 cm)

round vent

C Seal duct joints

with duct tape/

caulk

A. Roof cap

B. 6" (15.2 cm)

round vent

C Seal duct joints

with duct tape/

caulk

90 Elbo

w

6 ft (1.8 m)

2 ft

(0.6 m)

Wall cap

Évaluation

En savoir plus sur ce mode d’emploi

Nous comprenons qu’il est agréable d’avoir un mode d’emploi papier pour vos Whirlpool WVW7336JS Hotte aspirante. Vous pouvez toujours télécharger le mode d’emploi depuis notre site Web et l’imprimer vous-même. Si vous souhaitez disposer d’un mode d’emploi original, nous vous recommandons de contacter Whirlpool. Ils pourront peut-être fournir un mode d’emploi original. Recherchez-vous le mode d’emploi de votre Whirlpool WVW7336JS Hotte aspirante dans une autre langue ? Choisissez votre langue préférée sur notre page d’accueil et recherchez le numéro de modèle pour voir si nous l’avons disponible.

Caractéristiques

Tous les modes d’emploi pour Whirlpool Hottes aspirantes
Plus de modes d’emploi de Hottes aspirantes

Foire aux questions sur Whirlpool WVW7336JS Hotte aspirante

Notre équipe d’assistance recherche des informations utiles sur les produits et des réponses aux questions fréquemment posées. Si vous trouvez une inexactitude dans notre foire aux questions, veuillez nous le faire savoir en utilisant notre formulaire de contact.

Produits connexes

Mode d’emploi

Whirlpool HOO 501-S Hotte aspirante

Mode d’emploi

Whirlpool AKR 987 IX-4 Hotte aspirante

Mode d’emploi

Whirlpool WHVS 93F LT BSS/1 Hotte aspirante

Mode d’emploi

Whirlpool WAG HID 53F LE X Hotte aspirante

Mode d’emploi

Whirlpool AKR 976 NB Hotte aspirante

Mode d’emploi

Whirlpool WVW51UC0HV Hotte aspirante

Mode d’emploi

Whirlpool WVU17UC0JW Hotte aspirante

Mode d’emploi

Whirlpool AKR 950 IX Hotte aspirante

Catégories associées