Mode d’emploi Whirlpool WVW7336JS Hotte aspirante

Mode d’emploi

7

INSTALLATION INSTRUCTIONS

Prepare Location

■ It is recommended that the vent system be installed

beforehood is installed.

■ Before making cutouts, make sure there is proper

clearancewithin the ceiling or wall for exhaust vent.

■ Check your ceiling height and the hood height

maximumbefore you select your hood.

1. Disconnect power.

2. Determine which venting method to use: roof, wall, or

nonvented.

3. Select a at surface for assembling the range hood. Place

covering over that surface.

4. Using 2 or more people, lift range hood onto

coveredsurface.

Range Hood Mounting Screws Installation

1. Determine and mark the centerline on the wall where

thecanopy hood will be installed.

2. Select a mounting height between a minimum of 24" (61.0

cm) for an electric cooking surface, a minimum of 27" (68.6

cm) for a gas cooking surface, and a suggested maximum

of 36" (91.4 cm) above the range to the bottom of the hood.

Mark a reference line on the wall.

3. Tape template in place, aligning the template centerline and

bottom of template with hood bottom line and with the

centerline marked on the wall.

4. Mark centers of the fastener locations through the template

to the wall.

IMPORTANT: All canopy mounting screws must be installed

into wood where possible. If there is no wood to screw into,

additional wall framing supports may be required, or use

the (4) 10 x 60 mm wall anchors and 5.4 x 75 mm screws.

Remove the template.

5. For wood, drill

3

/

16

" (4.8 mm) pilot holes at all locations

wherescrews are being installed into wood.

For wall anchors, drill

7

/

16

" (10 mm) holes at all locations

where wall anchors are being used.

6. For wood, install (2) 5 x 45 mm mounting screws. Leave

a

1

/

4

" (6.4 mm) gap between the wall and the back of the

screw head to slide range hood into place.

For wall anchors, install the 10 x 60 mm wall anchors

andinstall the 5.4 x 75 mm screws into the wall anchors.

Tighten until the wall anchors are secure. Back the screws

out

1

/

4

" (6.4 mm).

Vent Cover Support Bracket Installation

Installations using telescoping upper and lower vent

coverassembly

1. Position vent cover bracket on wall about 1⁄8" (3.0 mm) away

from the ceiling.

2. Mark the hole locations.

3. Drill (2)

3

/

8

" (9.5 mm) holes for 8 x 40 mm wall anchors

andinsert anchors ush with the wall.

4. Attach vent cover support bracket to wall.

Complete Preparation

1. Determine and make all necessary cuts in the wall for the

vent system. Install the vent system before installing the

hood. See “Venting Requirements” section.

2. Determine the required height for the home power supply

cable and drill a 1

1

/

4

" (3.2 cm) hole at this location.

3. Run the home power supply cable according to the National

Electrical Code or CSA Standards and local codes and

ordinances. There must be enough ½" conduit and wires

from the fused disconnect (or circuit breaker) box to make

the connection in the hood’s electrical terminal box.

NOTE: Do not reconnect power until installation is complete.

4. Use caulk to seal all openings.

WARNING

Excessive Weight Hazard

Use two or more people to move and install

range hood.

Failure to do so can result in back or other injury.

Ver

tical Centerline

C

L

LLAW RAER

ETALPMET GNITNUOM

EGDE MOTTOB NGILA

ENIL LICNEP HTIW

MOTTOB GNITACIDNI

DOOH EHT FO

thgieH noitallatsnI

TROPPUS LLAW RAER RO SDUTS HGUORHT SELOH TOLIP "61/3 )OWT( 2 LLIRD

eniL latnoziroH

A

C

B

A. Centerline

B. Fastener locations

C. Mounting height reference

¹⁄₄"

(6.4 mm)

A

B

C

D

A. 8 x 40 mm wall anchors

B. Centerline on wall

C. Vent cover support bracket

D. 5 x 45 mm screws

Évaluation

En savoir plus sur ce mode d’emploi

Nous comprenons qu’il est agréable d’avoir un mode d’emploi papier pour vos Whirlpool WVW7336JS Hotte aspirante. Vous pouvez toujours télécharger le mode d’emploi depuis notre site Web et l’imprimer vous-même. Si vous souhaitez disposer d’un mode d’emploi original, nous vous recommandons de contacter Whirlpool. Ils pourront peut-être fournir un mode d’emploi original. Recherchez-vous le mode d’emploi de votre Whirlpool WVW7336JS Hotte aspirante dans une autre langue ? Choisissez votre langue préférée sur notre page d’accueil et recherchez le numéro de modèle pour voir si nous l’avons disponible.

Caractéristiques

Tous les modes d’emploi pour Whirlpool Hottes aspirantes
Plus de modes d’emploi de Hottes aspirantes

Foire aux questions sur Whirlpool WVW7336JS Hotte aspirante

Notre équipe d’assistance recherche des informations utiles sur les produits et des réponses aux questions fréquemment posées. Si vous trouvez une inexactitude dans notre foire aux questions, veuillez nous le faire savoir en utilisant notre formulaire de contact.

Produits connexes

Mode d’emploi

Whirlpool HOO 501-S Hotte aspirante

Mode d’emploi

Whirlpool AKR 987 IX-4 Hotte aspirante

Mode d’emploi

Whirlpool WHVS 93F LT BSS/1 Hotte aspirante

Mode d’emploi

Whirlpool WAG HID 53F LE X Hotte aspirante

Mode d’emploi

Whirlpool AKR 976 NB Hotte aspirante

Mode d’emploi

Whirlpool WVW51UC0HV Hotte aspirante

Mode d’emploi

Whirlpool WVU17UC0JW Hotte aspirante

Mode d’emploi

Whirlpool AKR 950 IX Hotte aspirante

Catégories associées