Mode d’emploi Rossmax SB100 Oxymètre de pouls

Mode d’emploi

Introduction

Error code for your reference

Rossmax Fingertip Pulse Oximeter SB100 is used

to measure arterial oxygen saturation (% SpO2)

of hemoglobin and pulse rate, an important

indicator of your respiratory function. It is non-

invasive device intended for spot-check of adult

and pediatric whose age is over 3 at home,

hospital and clinics.

Attention: Consult the accompanying

documents. Please read this manual

carefully before use. Please be sure to keep

this manual.

SENSOR ERROR:

Sensor cannot be de-

tected, return the device

to your local distributor or

service centre.

MEASURE ERROR:

Signals cannot be detect-

ed, turn the device off and

measure again.

Installing Batteries

1. Use thumb to slide battery cover out

2. Insert or replace 2 “AAA” sized batteries down

with the correct electrical polarity.

You need to replace the batteries when

1. Battery icon is blinking on display.

2. The function button is pressed and nothing

appears on display.

Caution: Batteries may leak or explode if used

or disposed of improperly. Remove

batteries if the device will be stored for

long time. Do not use different types

or brands of batteries at the same time.

Do not mix fully charged and partially

charged batteries at the same time.

Attaching the lanyard

1. Insert the narrow end of the

lanyard through the holder.

2. Draw the other end of the

lanyard through the loop at

the narrow end and tighten.

How to use

1. Open the clip; press the Power On button as .

2. Information of software version appears; insert

one finger, nail side up, into the finger opening

of the pulse oximeter.

Note: if no finger insert, the device will auto shut

off after 8 seconds.

3. The pulse strength indication shows “ ”, pulse

oximeter begins its measurement as .

Note: make sure the finger is lying flat, Do not shake

and keep body steady during measurement

as .

4. Your SpO2 and pulse rate values will appear on

the screen after few seconds as .

Note: 1. Don’t remove your finger until the

measurement is completed.

2. If SpO2 and pulse rate cannot be detected, “

“ will appear on the screen as .

3. While pulse strength is low, the reading

will flicker.

Note:

1. The SpO2 sensor and photoelectric receiving

tube should be arranged in a way with the

subject’s arteriole in a position there between.

2. Make sure the optical path is free from any

optical obstacles like rubberized fabric.

3. Excessive ambient light may affect the measuring

result. It includes fluorescent lamp, dual ruby

light, infrared heater, direct sunlight and etc.

4. Strenuous action of the subject or extreme

electrosurgical interference may also affect the

accuracy.

Cautionary Notes

- This device is to be operated by trained person-

nel only.

- This device has no audible and it intended only

for spot-checking, but not medical result evalu-

ation.

- This device is designed to determine the per-

centage of arterial oxygen saturation of func-

tional hemoglobin. Factors that may degrade

pulse oximeter performance or aect the accu-

racy of the measurement include the following:

• Do not apply the pulse oximeter on the same

arm as a blood pressure cu, arterial catheter or

infusion line(s)

• Excessive light, such as sunlight or direct home

lighting.

• Not steady at the site of application (e.g. trem-

bling)

• Moisture in the device

• Improperly applied device

• Finger is too large or too small to t into the

device.

• Poor pulse quality

• Venous pulsations

• Anemia or low hemoglobin concentrations.

• Cardiogreen and other intravascular dyes

• Carboxyhemoglobin

• Methemoglobin

• Dysfunctional hemoglobin

• Articial nails or ngernail polish

• On ngers with anatomical changes, oedemas,

scars or burns.

- Using the device for long periods may cause

pain for people with circulatory disorders. Repo-

sition the device at least once every 4 hours to

allow the patient’s skin to breath and to check

patient’s condition regularly.

- Do not use the device near ammable or explo-

sive gas mixtures.

- Do not use the device during an MRI or CT scan.

- The device may not work when circulation is

reduced. Warm or rub the nger, or re-position

the device.

- This device is a precision electronic instrument

and must be repaired by qualied technical pro-

fessionals. Field repair of the device is not pos-

sible. Do no attempt to open the case or repair

the electronics. Opening the case may damage

the device and void the warranty.

- Do not overextend the device’s spring.

1. SpO2 icon

2. Pulse strength

indication

3. Pulse rate icon

7

1

2

3

4

5

6

4. Beats per minute

5. Power On Button

6. Battery icon

7. Battery compartment

Name/ Functions of each part

Évaluation

En savoir plus sur ce mode d’emploi

Nous comprenons qu’il est agréable d’avoir un mode d’emploi papier pour vos Rossmax SB100 Oxymètre de pouls. Vous pouvez toujours télécharger le mode d’emploi depuis notre site Web et l’imprimer vous-même. Si vous souhaitez disposer d’un mode d’emploi original, nous vous recommandons de contacter Rossmax. Ils pourront peut-être fournir un mode d’emploi original. Recherchez-vous le mode d’emploi de votre Rossmax SB100 Oxymètre de pouls dans une autre langue ? Choisissez votre langue préférée sur notre page d’accueil et recherchez le numéro de modèle pour voir si nous l’avons disponible.

Caractéristiques

Tous les modes d’emploi pour Rossmax Oxymètres de pouls
Plus de modes d’emploi de Oxymètres de pouls

Produits connexes

Mode d’emploi

SilverCrest IAN 322246 Oxymètre de pouls

Mode d’emploi

1byOne 704NA-0004 Oxymètre de pouls

Mode d’emploi

SilverCrest IAN 290989 Oxymètre de pouls

Mode d’emploi

Medisana PM A10 Oxymètre de pouls

Mode d’emploi

Homedics PX-130 Oxymètre de pouls

Mode d’emploi

Medisana PM 100 Oxymètre de pouls

Mode d’emploi

Beper P303MED050 Oxymètre de pouls

Mode d’emploi

Gima OXY-5 Oxymètre de pouls

Catégories associées